If we make all UART addressing consistent across all ColdFire family members
then we will be able to remove the duplicated plaform data and use a single
setup for all.

So modify the ColdFire 5249 UART addressing so that:

. UARTs are numbered from 0 up
. base addresses are absolute (not relative to MBAR peripheral register)
. use a common name for IRQs used
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

If we make all UART addressing consistent across all ColdFire family members
then we will be able to remove the duplicated plaform data and use a single
setup for all.

So modify the ColdFire 523x UART addressing so that:

. UARTs are numbered from 0 up
. use a common name for IRQs used
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

If we make all UART addressing consistent across all ColdFire family members
then we will be able to remove the duplicated plaform data and use a single
setup for all.

So modify the ColdFire 520x UART addressing so that:

. UARTs are numbered from 0 up
. use a common name for IRQs used
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

If we make all UART addressing consistent across all ColdFire family members
then we will be able to remove the duplicated plaform data and use a single
setup for all.

So modify the ColdFire 5206 UART addressing so that:

. UARTs are numbered from 0 up
. base addresses are absolute (not relative to MBAR peripheral register)
. use a common name for IRQs used
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

The MMU and non-MMU varients of the m68k arch process.c code are pretty
much the same. Only a few minor details differ between the two. The
majority of the difference is to deal with having or wanting hardware FPU
support. So merge them back into a single process.c file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>

The classic m68k code has always supported an FPU (although it may have
been a software emulated one). The non-MMU m68k code has never supported FPU
hardware. To help in merging common code create a configation setting that
signifies if we are builing in FPU support or not.

This switch, CONFIG_FPU, is set as per the current use cases. So it is
always enabled if CONFIG_MMU is set, and disabled otherwise. With a little
extra code it will be possible to disable it on the classic m68k platforms
as well, and to enable it on non-MMU platforms that do have hardware FPU.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>

Most of the code in the non-mmu ptrace_no.c file is the same as the mmu
version ptrace_mm.c. So merge them back into a single file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>

The set_rtc_mmss() function is defined "static inline" but is never used
in this file. Remove it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>

There is only trivial differences between the mmu time_mm.c and non-mmu
time_no.c files. Merge them back into a single time.c.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>

The CONFIG_GENERIC_CMOS_UPDATE switch is always enabled for the non-MMU
m68k case. But the underlying code to support it, update_persistent_clock(),
doesn't end up doing anything on the currently supported non-MMU platforms.
No platforms supply the necessary function support for writing back the RTC.

So lets remove this option and support code. This also brings m68knommu
in line with the m68k, which doesn't enabled this switch either.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

With a few small changes we can make the m68knommu timer init code the
same as the m68k code. By using the mach_sched_init function pointer
and reworking the current timer initializers to keep track of the common
m68k timer_interrupt() handler we end up with almost identical code for
m68knommu.

This will allow us to more easily merge the mmu and non-mmu m68k time.c
in future patches.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

The read_persistent_clock() code is different on m68knommu, for really no
reason. With a few changes to support function names and some code
re-organization the code can be made the same.

This will make it easier to merge the arch/m68k/kernel/time.c for m68k and
m68knommu in a future patch.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

The base of the real RAM resident hardware vectors, _ramvec, is declared in
our asm/traps.h. No need to have local declarations spread around in other
files that use this. So remove them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

There is a lot of years of collected cruft in the m68knommu linker script.
Clean it all up and use the well defined linker script support macros.

Support is maintained for building both ROM/FLASH based and RAM based setups.
No major changes to section layouts, though the rodata section is now lumped
in with the read/write data section.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

The ColdFire MBAR register that holds the mapping of the peripheral region
on some ColdFire CPUs is configurable. It can be configured at some address
different to that of the bootloader that loaded the kernel. So hard set
the MBAR register mapping at kernel startup time.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>

SCSI fixes from James Bottomley:
 "There's just a single fix in here: the osd max device number fix."

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] osd_uld: Bump MAX_OSD_DEVICES from 64 to 1,048,576

PARISC fixes from James Bottomley:
 "This is a set of build fixes to get the cross compiled architecture
  testbeds building again"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] don't unconditionally override CROSS_COMPILE for 64 bit.
  [PARISC] include <linux/prefetch.h> in drivers/parisc/iommu-helpers.h
  [PARISC] fix compile break caused by iomap: make IOPORT/PCI mapping functions conditional

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/kvm: Fix Host-Only/Guest-Only counting with SVM disabled

Pull from Herbert Xu:
  "This push fixes a bug in mv_cesa that causes all hash operations
   that supply data on a final operation to fail."

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: mv_cesa - fix final callback not ignoring input data

Commit 5707c87f "vfs: uninline full_name_hash()" broke the modular
build, because it needs exporting now that it isn't inlined any more.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

hhwmon fixes for 3.3-rc6 from Guenter Roeck:

These patches are necessary for correct operation and management of
F75387.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (f75375s) Catch some attempts to write to r/o registers
  hwmon: (f75375s) Properly map the F75387 automatic modes to pwm_enable
  hwmon: (f75375s) Make pwm*_mode writable for the F75387
  hwmon: (f75375s) Fix writes to the pwm* attribute for the F75387

fbdev fixes for 3.3 from Florian Tobias Schandinat

It includes:
 - two fixes for OMAP HDMI
 - one fix to make new OMAP functions behave as they are supposed to
 - one Kconfig dependency fix
 - two fixes for viafb for modesetting on VX900 hardware

* tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6:
  OMAPDSS: APPLY: make ovl_enable/disable synchronous
  OMAPDSS: panel-dvi: Add Kconfig dependency on I2C
  viafb: fix IGA1 modesetting on VX900
  viafb: select HW scaling on VX900 for IGA2
  OMAPDSS: HDMI: hot plug detect fix
  OMAPDSS: HACK: Ensure DSS clock domain gets out of idle when HDMI is enabled

sound fixes for 3.3-rc6 from Takashi Iwai

This contains again regression fixes for various HD-audio and ASoC
regarding SSI and dapm shutdown path.  In addition, a minor azt3328
fix and the correction of the new jack-notification strings in HD-audio.

* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Kill hyphenated names
  ALSA: hda - Add a fake mute feature
  ALSA: hda - Always set HP pin in unsol handler for STAC/IDT codecs
  ALSA: azt3328 - Fix NULL ptr dereference on cards without OPL3
  ALSA: hda/realtek - Fix resume of multiple input sources
  ASoC: i.MX SSI: Fix DSP_A format.
  ASoC: dapm: Check for bias level when powering down

The code in link_path_walk() that finds out the length and the hash of
the next path component is some of the hottest code in the kernel.  And
I have a version of it that does things at the full width of the CPU
wordsize at a time, but that means that we *really* want to split it up
into a separate helper function.

So this re-organizes the code a bit and splits the hashing part into a
helper function called "hash_name()".  It returns the length of the
pathname component, while at the same time computing and writing the
hash to the appropriate location.

The code generation is slightly changed by this patch, but generally for
the better - and the added abstraction actually makes the code easier to
read too.  And the new interface is well suited for replacing just the
"hash_name()" function with alternative implementations.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It did some odd things for unclear reasons.  As this is one of the
functions that gets changed when doing word-at-a-time compares, this is
yet another of the "don't change any semantics, but clean things up so
that subsequent patches don't get obscured by the cleanups".
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

.. and also use it in lookup_one_len() rather than open-coding it.

There aren't any performance-critical users, so inlining it is silly.
But it wouldn't matter if it wasn't for the fact that the word-at-a-time
dentry name patches want to conditionally replace the function, and
uninlining it sets the stage for that.

So again, this is a preparatory patch that doesn't change any semantics,
and only prepares for a much cleaner and testable word-at-a-time dentry
name accessor patch.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

These don't change any semantics, but they clean up the code a bit and
mark some arguments appropriately 'const'.

They came up as I was doing the word-at-a-time dcache name accessor
code, and cleaning this up now allows me to send out a smaller relevant
interesting patch for the experimental stuff.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It makes no sense to attempt to manually configure the fan in auto mode,
or set the duty cycle directly in closed loop mode.  The corresponding
registers are then read-only.  If the user tries it nonetheless, error out
with EINVAL instead of silently doing nothing.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Minor formatting cleanup]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

The F75387 supports automatic fan control using either PWM duty cycle or
RPM speed values.  Make the driver detect the latter mode, and expose the
different modes in sysfs as per pwm_enable, so that the user can switch
between them.

The interpretation of the pwm_enable attribute for the F75387 is adjusted
to be a superset of those values used for similar Fintek chips which do
not support automatic duty mode, with 2 mapping to automatic speed mode,
and moving automatic duty mode to the new value 4.

Toggling the duty mode via pwm_enable is currently denied for the F75387,
as the chip then simply reinterprets the fan configuration register values
according to the new mode, switching between RPM and PWM units, which
makes this a dangerous operation.

This patch introduces a new pwm mode into the driver. This is necessary
because the new mode (automatic pwm mode, 4) may already be enabled by the
BIOS, and the driver should not break existing functionality. This was seen
on at least one board.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

Merge branches 'core-urgent-for-linus', 'perf-urgent-for-linus' and 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pulling latest branches from Ingo:

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  memblock: Fix size aligning of memblock_alloc_base_nid()

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf probe: Ensure offset provided is not greater than function length without DWARF info too
  perf tools: Ensure comm string is properly terminated
  perf probe: Ensure offset provided is not greater than function length
  perf evlist: Return first evsel for non-sample event on old kernel
  perf/hwbp: Fix a possible memory leak

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  CPU hotplug, cpusets, suspend: Don't touch cpusets during suspend/resume

There is only one error code to return for a bad user-space buffer
pointer passed to a system call in the same address space as the
system call is executed, and that is EFAULT.  Furthermore, the
low-level access routines, which catch most of the faults, return
EFAULT already.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The regset common infrastructure assumed that regsets would always
have .get and .set methods, but not necessarily .active methods.
Unfortunately people have since written regsets without .set methods.

Rather than putting in stub functions everywhere, handle regsets with
null .get or .set methods explicitly.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It turned out that a performance counter on AMD does not
count at all when the GO or HO bit is set in the control
register and SVM is disabled in EFER.

This patch works around this issue by masking out the HO bit
in the performance counter control register when SVM is not
enabled.

The GO bit is not touched because it is only set when the
user wants to count in guest-mode only. So when SVM is
disabled the counter should not run at all and the
not-counting is the intended behaviour.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Avi Kivity <avi@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: stable@vger.kernel.org # v3.2
Link: http://lkml.kernel.org/r/1330523852-19566-1-git-send-email-joerg.roedel@amd.comSigned-off-by: Ingo Molnar <mingo@elte.hu>

Kill hyphens from "Line-Out" name strings, as suggested by Mark Brown.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'perf-urgent-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent

Various smaller perf/urgent fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Watchdog updates from Wim Van Sebroeck:

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: fix GETTIMEOUT ioctl in booke_wdt
  watchdog: update maintainers git entry
  watchdog: Fix typo in pnx4008_wdt.c
  watchdog: Fix typo in Kconfig
  watchdog: fix error in probe() of s3c2410_wdt (reset at booting)
  watchdog: hpwdt: clean up set_memory_x call for 32 bit

Pull from Mark Brown:
 "A simple, driver specific fix.  This device isn't widely used outside
  of Marvell reference boards most of which are probably used with their
  BSPs rather than with mainline so low risk."

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: fix the ldo configure according to 88pm860x spec

i2c bugfix from Wolfram Sang:
  "This patch fixes a wrong assumption in the mxs-i2c-driver about a
   command queue being done.  Without it, we have seen races when the
   bus was under load."

* 'i2c-embedded/for-3.3' of git://git.pengutronix.de/git/wsa/linux-2.6:
  i2c: mxs: only flag completion when queue is completely done

DRM fixes from Dave Airlie:
  intel: fixes for output regression on 965GM, an oops and a machine
  hang

  radeon: uninitialised var (that gcc didn't warn about for some reason)
  + a couple of correctness fixes.

  exynos: fixes for various things, drop some chunks of unused code.

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms/vm: fix possible bug in radeon_vm_bo_rmv()
  drm/radeon: fix uninitialized variable
  drm/radeon/kms: fix radeon_dp_get_modes for LVDS bridges (v2)
  drm/i915: Remove use of the autoreported ringbuffer HEAD position
  drm/i915: Prevent a machine hang by checking crtc->active before loading lut
  drm/i915: fix operator precedence when enabling RC6p
  drm/i915: fix a sprite watermark computation to avoid divide by zero if xpos<0
  drm/i915: fix mode set on load pipe. (v2)
  drm/exynos: exynos_drm.h header file fixes
  drm/exynos: added panel physical size.
  drm/exynos: added postclose to release resource.
  drm/exynos: removed exynos_drm_fbdev_recreate function.
  drm/exynos: fixed page flip issue.
  drm/exynos: added possible_clones setup function.
  drm/exynos: removed pageflip_event_list init code when closed.
  drm/exynos: changed priority of mixer layers.
  drm/exynos: Fix typo in exynos_mixer.c