Merge tag 'renesas-multiplatform-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

From Simon Horman:
Renesas ARM based SoC multiplatform updates for v3.12

Move Renesas ARM based SoCs a little closer to using
multiplatform by adding ARCH_SHMOBILE_MULTI and only
building clocks when COMMON_CLK=n.

* tag 'renesas-multiplatform-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: Allow ARCH_SHMOBILE_MULTI timer configuration
  ARM: shmobile: Add EMEV2 and KZM9D to ARCH_SHMOBILE_MULTI
  ARM: shmobile: Introduce ARCH_SHMOBILE_MULTI
  ARM: shmobile: Only build clocks when COMMON_CLK=n
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-pinmux-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

From Simon Horman:
Renesas ARM based SoC pinmux updates for v3.12

SH Mobile pinctrl DT support

* tag 'renesas-pinmux-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: kzm9g-reference: Add LED1-LED4 to the device tree
  ARM: shmobile: kzm9g-reference: Move SDHI regulators to DT
  ARM: shmobile: kzm9g-reference: Move pinctrl mappings to device tree
  ARM: shmobile: marzen-reference: Add LED2-LED4 to the device tree
  ARM: shmobile: marzen-reference: Move pinctrl mappings to device tree
  ARM: shmobile: armadillo-reference: Add LED1-LED4 to the device tree
  ARM: shmobile: armadillo-reference: Move st1232 reset GPIO to DT
  ARM: shmobile: armadillo-reference: Add st1232 pin mappings
  ARM: shmobile: armadillo-reference: Move pinctrl mappings to device tree
  ARM: shmobile: sh73a0: Add pin control device to device tree
  ARM: shmobile: sh7372: Add pin control device to device tree
  ARM: shmobile: r8a7790: Add GPIO controller devices to device tree
  ARM: shmobile: r8a7790: Add pin control device to device tree
  ARM: shmobile: r8a7779: Add GPIO controller devices to device tree
  ARM: shmobile: r8a7779: Add pin control device to device tree
  ARM: shmobile: r8a7778: Add GPIO controller devices to device tree
  ARM: shmobile: r8a7778: Add pin control device to device tree
  ARM: shmobile: r8a7740: Add pin control device to device tree
  ARM: shmobile: r8a73a4: Add pin control device to device tree
Signed-off-by: Olof Johansson <olof@lixom.net>

Conflicts:
	arch/arm/boot/dts/r8a73a4.dtsi
	arch/arm/boot/dts/r8a7790.dtsi

From: Haojian Zhuang <haojian.zhuang@gmail.com>:
* pxa/dt:
  ARM: pxa: DTS: override gpio node in pxa3xx.dtsi
  ARM: pxa: fix DT auxdata for pxa3xx-gpio
Signed-off-by: Kevin Hilman <khilman@linaro.org>

The gpio controller node inherited from pxa2xx.dtsi won't work for
pxa3xx SoCs, so let's override it in pxa3xx.dtsi.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>

Commit f8731174 ("ARM: mmp: add more compatible names in gpio driver")
changed the DT match string for pxa3xx-gpio, but left the auxdata table
unchanged.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-dt-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

From Simon Horman:
Renesas ARM-based SoC DT updates for v3.12

* Reference implementation for kzm9d board
* Add MMCIF and SDHI DT templates for r8a7790 and r8a73a4 SoCs
* Use DT for SMP and GIC initialisation on emev2 SoC and kzm9d board
* Add GIO to dtsi of emev2 SoC
* Update dts command line of kzm9d board
* Add CPUFreq support to ape6evm board
* Add I2C controller DT nodes to r8a73a4 SoC

* tag 'renesas-dt-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (33 commits)
  ARM: shmobile: Add SMSC ethernet chip to KZM9D DT reference
  ARM: shmobile: KZM9D DT reference implementation
  ARM: shmobile: r8a7790: add MMCIF and SDHI DT templates
  ARM: shmobile: r8a73a4: add MMCIF and SDHI DT templates
  ARM: shmobile: EMEV2 map_io update
  ARM: shmobile: Use DT for SMP on EMEV2 and KZM9D
  ARM: shmobile: Use DT for GIC on EMEV2 and KZM9D
  ARM: shmobile: Add GIO to EMEV2 dtsi
  ARM: shmobile: Update KZM9D dts command line
  ARM: shmobile: ape6evm: add CPUFreq support
  ARM: shmobile: r8a73a4: add I2C controller DT nodes
  ARM: shmobile: Remove unused mach/dma.h
  ARM: shmobile: r8a7778: remove r8a7778_init_irq()
  ARM: shmobile: Fix EMEV2 clock comment typo
  ARM: shmobile: Make EMEV2 platform devices more compact
  ARM: shmobile: Remove unused EMEV2/KZM9D early console
  ARM: shmobile: Remove redundant r8a7790 callback
  ARM: shmobile: Remove unused sh73a0 auxdata table
  ARM: shmobile: Remove unused sh7372 auxdata table
  ARM: shmobile: Remove unused r8a7779 auxdata table
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Move the timer configuration bits to allow use in
case of ARCH_SHMOBILE or ARCH_SHMOBILE_MULTI.

The timers all make use of the regular driver model
so they are safe to enable for ARCH_MULTIPLATFORM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable build of EMEV2 and KZM9D DT Reference in
case of ARCH_MULTIPLATFORM and ARCH_SHMOBILE_MULTI.

IS_ENABLED() is leaves the clock-emev2.c file out
in case of COMMON_CLK=y.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add ARCH_SHMOBILE_MULTI to mach-shmobile that can be used
to enable ARCH_MULTIPLATFORM on selected SoCs and boards.

The headers stay under arch/arm/mach-shmobile/include/mach/
for now, they can and will be migrated independently over time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Move shared clock.c file and per-SoC clock-xxx.c files
to only build when CONFIG_COMMON_CLK != y.

The regular ARCH_SHMOBILE case with legacy SH clock framework
will build just as before with this patch applied, however
the case when COMMON_CLK=y will exclude all the clock files.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

LED1 to LED4 are GPIO LEDs. Add corresponding DT nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Create two GPIO-controlled fixed-voltage regulators in the
kzm9g-reference DT and remove manual configuration of the corresponding
GPIOs from board code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Replace the pinctrl mappings in board code by device tree mappings.
For devices that are still instantiated from board code reference the
mappings as the default pin controller state to apply them at boot time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

LED2 to LED4 are GPIO LEDs. Add corresponding DT nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Replace the pinctrl mappings in board code by device tree mappings.
For devices that are still instantiated from board code reference the
mappings as the default pin controller state to apply them at boot time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

LED1 to LED4 are GPIO LEDs. Add corresponding DT nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Reference the st1232 reset GPIO from the device tree and remove it from
board code.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add pin mappings for the st1232 device to the device tree and reference
them as the default state for the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Replace the pinctrl mappings in board code by device tree mappings.
For devices that are still instantiated from board code reference the
mappings as the default pin controller state to apply them at boot time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a pfc node to the sh73a0 device tree and remove manual pinmux
initialization from the corresponding board files.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a pfc node to the sh7372 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add GPIO controller nodes to the r8a7790 core device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a pfc node to the r8a7790 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add GPIO controller nodes to the r8a7779 core device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a pfc node to the r8a7779 device tree and remove manual pinmux
initialization from the corresponding board files.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add GPIO controller nodes to the r8a7778 core device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a pfc node to the r8a7778 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a pfc node to the r8a7740 device tree and remove manual pinmux
initialization from the corresponding board files.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a pfc node to the r8a73a4 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[g.liakhovetski+renesas@gmail.com use 2 nodes for address and size]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add support for the SMSC ethernet controller found
on the KZM9D board to the KZM9D DT Reference code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a DT reference implementation for the KZM9D board.

Only DT devices are used in this case. UART, STI, GPIO
and SMP / GIC are all provided by emev2.dtsi.

There is still a board specific C file used for enabling
legacy SH clocks. This file will be removed after we have
moved over to common clocks.
Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: Do not include trailing blank line in
 board-kzm9d-reference.c ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This adds DT templates for all MMCIF and SDHI controllers on r8a7790.
They are added with status="disabled". To use them platform-specific
DTs have to enable the required ones.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This adds DT templates for all MMCIF and SDHI controllers on r8a73a4.
They are added with status="disabled". To use them platform-specific
DTs have to enable the required ones.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Update the EMEV2 struct map_desc to exclude the SMU
and also include the ->map_io() callback in the DT
version of EMEV2 board support.

The EMEV2 SMP code can these days perform ioremap()
early on without the SMU information in the io_desc[].

To correctly support SMP in case of DT-only board
support then the ->map_io() callback is needed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Rework the EMEV2 SMP code to rely on DT for CPU information
instead of reading out number of CPU cores from the SCU.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Remove the C version of the EMEV2 GIC setup code,
instead rely on GIC information provided by DT.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add GIO0->GIO4 device nodes to the EMEV2 dtsi file.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Update the KZM9D DTS command line to remove following cruft:
 - console=tty0 - no graphic support upstream anyway
 - earlyprintk= - not supported by the 8250-em driver anyway
 - mem= - this is provided via DT anyway
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds OPPs to the CA15 DT node and a max8973 DT node to support
clock and voltage scaling, using the cpufreq-cpu0 CPUFreq driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add Device Tree nodes for the 9 I2C controllers on r8a73a4, compatible with
the i2c-sh_mobile.c driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>