Current commit 0775f9f9
"mac80211: remove spurious BSSID change flag" exposed bug on iwlegacy,
that we do not set BSSID address correctly and then device was not able
to receive frames after successful associate.

On the way fix scan canceling comment. Apparently ->post_associate()
do cancel scan itself, but scan cancel on BSS_CHANGED_BSSID is needed.
I'm not sure why, but when I removed it, I had frequent auth failures:

 wlan4: send auth to 54:e6:fc:98:63:fe (try 1/3)
 wlan4: send auth to 54:e6:fc:98:63:fe (try 2/3)
 wlan4: send auth to 54:e6:fc:98:63:fe (try 3/3)
 wlan4: authentication with 54:e6:fc:98:63:fe timed out
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently the maximum noise floor limit is set as too high (-60dB). The
assumption of having a higher threshold limit is that it would help
de-sensitize the receiver (reduce phy errors) from continuous
interference. But when we have a bursty interference where there are
collisions and then free air time and if the receiver is desensitized too
much, it will miss the normal packets too. Lets make use of chips
specific min, nom and max limits always. This patch helps to improve the
connection stability in congested networks.

Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@google.com>
Tested-by: Gary Morain <gmorain@google.com>
Signed-off-by: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This il->vif is dereferenced in different part of iwlegacy code, so do
not nullify it. This should fix random crashes observed in companion
with microcode errors i.e. crash in il3945_config_ap().

Additionally this should address also
WARNING: at drivers/net/wireless/iwlegacy/common.c:4656 il_mac_remove_interface
at least one of the possible reasons of that warning.

Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

usbnet should centrally handle busy reporting in the rx path
so subdrivers need not worry. This hurts use cases which do
rx only or predominantly.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following patch aimed to resolve an issue where secondary, tertiary,
etc. addresses added to bond interfaces could overwrite the
bond->master_ip and vlan_ip values.

        commit 917fbdb3
        Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
        Date:   Wed Nov 23 23:37:15 2011 +0000

            bonding: only use primary address for ARP

That patch was good because it prevented bonds using ARP monitoring from
sending frames with an invalid source IP address.  Unfortunately, it
didn't always work as expected.

When using an ioctl (like ifconfig does) to set the IP address and
netmask, 2 separate ioctls are actually called to set the IP and netmask
if the mask chosen doesn't match the standard mask for that class of
address.  The first ioctl did not have a mask that matched the one in
the primary address and would still cause the device address to be
overwritten.  The second ioctl that was called to set the mask would
then detect as secondary and ignored, but the damage was already done.

This was not an issue when using an application that used netlink
sockets as the setting of IP and netmask came down at once.  The
inconsistent behavior between those two interfaces was something that
needed to be resolved.

While I was thinking about how I wanted to resolve this, Ralf Zeidler
came with a patch that resolved this on a RHEL kernel by keeping a full
shadow of the entries in dev->ifa_list for the bonding device and vlan
devices in the bonding driver.  I didn't like the duplication of the
list as I want to see the 'bonding' struct and code shrink rather than
grow, but liked the general idea.

As the Subject indicates this patch drops the master_ip and vlan_ip
elements from the 'bonding' and 'vlan_entry' structs, respectively.
This can be done because a device's address-list is now traversed to
determine the optimal source IP address for ARP requests and for checks
to see if the bonding device has a particular IP address.  This code
could have all be contained inside the bonding driver, but it made more
sense to me to EXPORT and call inet_confirm_addr since it did exactly
what was needed.

I tested this and a backported patch and everything works as expected.
Ralf also helped with verification of the backported patch.

Thanks to Ralf for all his help on this.

v2: Whitespace and organizational changes based on suggestions from Jay
Vosburgh and Dave Miller.

v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's
suggestion.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Ralf Zeidler <ralf.zeidler@nsn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It used to be an int, and it got changed to a bool parameter at least
7 years ago.  It happens that NF_ACCEPT and NF_DROP are 0 and 1, so
this works, but it's unclear, and the check that it's in range is not
required.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

URB unlinking is always racing with its completion and tx_complete
may be called before or during running usb_unlink_urb, so tx_complete
must not clear urb->dev since it will be used in unlink path,
otherwise invalid memory accesses or usb device leak may be caused
inside usb_unlink_urb.

Cc: stable@kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 4231d47e(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock, but it makes usb_unlink_urb
racing with defer_bh, and the URB to being unlinked may be freed before
or during calling usb_unlink_urb, so use-after-free problem may be
triggerd inside usb_unlink_urb.

The patch fixes the use-after-free problem by increasing URB
reference count with skb queue lock held before calling
usb_unlink_urb, so the URB won't be freed until return from
usb_unlink_urb.

Cc: stable@kernel.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We call the wrong replay notify function when we use ESN replay
handling. This leads to the fact that we don't send notifications
if we use ESN. Fix this by calling the registered callbacks instead
of xfrm_replay_notify().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The xfrm_state argument is unused in this function, so remove it.
Also the name xfrm_state_check_space does not really match what this
function does. It actually checks if we have enough head and tailroom
on the skb. So we rename the function to xfrm_skb_check_space.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should be using the gfp flags the caller specified here, instead of
GFP_KERNEL.  I think this might be a bugfix, depending on the value of
"sock->sk->sk_allocation" when we call rds_conn_create_outgoing() in
rds_sendmsg().  Otherwise, it's just a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function takes a GFP flags as a parameter, but they are never used.
We don't take a lock in this function so there is no reason to prefer
GFP_ATOMIC over the caller's GFP flags.

There is only one caller, cipso_v4_map_cat_rng_ntoh(), and it passes
GFP_ATOMIC as the GFP flags so this doesn't change how the code works.
It's just a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When L2TP is configured as a module, requests for L2TP sockets do not result
in the l2tp_ppp module being loaded.  Fix this by adding the appropriate
MODULE_ALIAS to be recognized by pppox's request_module() call.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The recently added parity error handling used an error code that was
already defined for a different error.  This could lead to bnx2x
firmware assert.  We need to fix this with new error codes that are
defined for parity error only.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RSS feature in tg3 hardware has only one rx producer ring for all
RSS rings.  NAPI vector 1 is special and handles the refilling of the
rx producer ring on behalf of all RSS rings.  There is a race condition
between these RSS NAPIs and the NAPI[1].  If NAPI[1] finishes checking
for refill and then another RSS ring empties the rx producer ring
before NAPI[1] exits NAPI, the chip will be completely out of SKBs in
the rx producer ring.

We fix this by adding a flag tp->rx_refill and rely on napi_schedule()/
napi_complete() to help synchronize it to close the race condition.

Update driver version to 3.123.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some BIOS's don't setup power management correctly (what else is
new) and don't allow use of PCI Express power control. Add a special
exception module parameter to allow working around this issue.
Based on slightly different patch by Knut Petersen.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi->skb is allocated in napi_get_frags() using
netdev_alloc_skb_ip_align(), with a reserve of NET_SKB_PAD +
NET_IP_ALIGN bytes.

However, when such skb is recycled in napi_reuse_skb(), it ends with a
reserve of NET_IP_ALIGN which is suboptimal.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull security subsystem updates for 3.4 from James Morris:
 "The main addition here is the new Yama security module from Kees Cook,
  which was discussed at the Linux Security Summit last year.  Its
  purpose is to collect miscellaneous DAC security enhancements in one
  place.  This also marks a departure in policy for LSM modules, which
  were previously limited to being standalone access control systems.
  Chromium OS is using Yama, and I believe there are plans for Ubuntu,
  at least.

  This patchset also includes maintenance updates for AppArmor, TOMOYO
  and others."

Fix trivial conflict in <net/sock.h> due to the jumo_label->static_key
rename.

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (38 commits)
  AppArmor: Fix location of const qualifier on generated string tables
  TOMOYO: Return error if fails to delete a domain
  AppArmor: add const qualifiers to string arrays
  AppArmor: Add ability to load extended policy
  TOMOYO: Return appropriate value to poll().
  AppArmor: Move path failure information into aa_get_name and rename
  AppArmor: Update dfa matching routines.
  AppArmor: Minor cleanup of d_namespace_path to consolidate error handling
  AppArmor: Retrieve the dentry_path for error reporting when path lookup fails
  AppArmor: Add const qualifiers to generated string tables
  AppArmor: Fix oops in policy unpack auditing
  AppArmor: Fix error returned when a path lookup is disconnected
  KEYS: testing wrong bit for KEY_FLAG_REVOKED
  TOMOYO: Fix mount flags checking order.
  security: fix ima kconfig warning
  AppArmor: Fix the error case for chroot relative path name lookup
  AppArmor: fix mapping of META_READ to audit and quiet flags
  AppArmor: Fix underflow in xindex calculation
  AppArmor: Fix dropping of allowed operations that are force audited
  AppArmor: Add mising end of structure test to caps unpacking
  ...

Pull crypto update from Herbert Xu:
 "* sha512 bug fixes (already in your tree).
  * SHA224/SHA384 AEAD support in caam.
  * X86-64 optimised version of Camellia.
  * Tegra AES support.
  * Bulk algorithm registration interface to make driver registration easier.
  * padata race fixes.
  * Misc fixes."

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (31 commits)
  padata: Fix race on sequence number wrap
  padata: Fix race in the serialization path
  crypto: camellia - add assembler implementation for x86_64
  crypto: camellia - rename camellia.c to camellia_generic.c
  crypto: camellia - fix checkpatch warnings
  crypto: camellia - rename camellia module to camellia_generic
  crypto: tcrypt - add more camellia tests
  crypto: testmgr - add more camellia test vectors
  crypto: camellia - simplify key setup and CAMELLIA_ROUNDSM macro
  crypto: twofish-x86_64/i586 - set alignmask to zero
  crypto: blowfish-x86_64 - set alignmask to zero
  crypto: serpent-sse2 - combine ablk_*_init functions
  crypto: blowfish-x86_64 - use crypto_[un]register_algs
  crypto: twofish-x86_64-3way - use crypto_[un]register_algs
  crypto: serpent-sse2 - use crypto_[un]register_algs
  crypto: serpent-sse2 - remove dead code from serpent_sse2_glue.c::serpent_sse2_init()
  crypto: twofish-x86 - Remove dead code from twofish_glue_3way.c::init()
  crypto: In crypto_add_alg(), 'exact' wants to be initialized to 0
  crypto: caam - fix gcc 4.6 warning
  crypto: Add bulk algorithm registration interface
  ...

Pull hwmon changes for v3.4 from Guenter Roeck:
 "Mostly cleanup.  No new drivers this time around, but support for
  several chips added to existing drivers: TPS40400, TPS40422, MTD040,
  MAX34446, ZL9101M, ZL9117M, and LM96080.  Also, added watchdog support
  for SCH56xx, and additional attributes for a couple of drivers."

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (137 commits)
  hwmon: (sch56xx) Add support for the integrated watchdog (v2)
  hwmon: (w83627ehf) Add support for temperature offset registers
  hwmon: (jc42) Remove unnecessary device IDs
  hwmon: (zl6100) Add support for ZL9101M and ZL9117M
  hwmon: (adm1275) Add support for ADM1075
  hwmon: (max34440) Add support for MAX34446
  hwmon: (pmbus) Add more virtual registers
  hwmon: (pmbus) Add support for Lineage Power MDT040
  hwmon: (pmbus) Add support for TI TPS40400 and TPS40422
  hwmon: (max34440) Add support for 'lowest' output voltage attribute
  hwmon: (jc42) Convert to use devm_kzalloc
  hwmon: (max16065) Convert to use devm_kzalloc
  hwmon: (smm665) Convert to use devm_kzalloc
  hwmon: (ltc4261) Convert to use devm_kzalloc
  hwmon: (pmbus) Simplify remove functions
  hwmon: (pmbus) Convert pmbus drivers to use devm_kzalloc
  hwmon: (lineage-pem) Convert to use devm_kzalloc
  hwmon: (hwmon-vid) Fix checkpatch issues
  hwmon: (hwmon-vid) Add new entries to VRM model table
  hwmon: (lm80) Add detection of NatSemi/TI LM96080
  ...

Pull regulator updates for 3.4 from Mark Brown:
 "This has been a fairly quiet release from a regulator point of view,
  the only real framework features added were devm support and a
  convenience helper for setting up fixed voltage regulators.

  We also added a couple of drivers (but will drop the BQ240022 driver
  via the arm-soc tree as it's been replaced by the more generic
  gpio-regulator driver) and Axel Lin continued his relentless and
  generally awesome stream of fixes and cleanups."

* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (93 commits)
  regulator: Fix up a confusing dev_warn when DT lookup fails
  regulator: Convert tps6507x to set_voltage_sel
  regulator: Refactor tps6507x to use one tps6507x_pmic_ops for all LDOs and DCDCs
  regulator: Make s5m8767_get_voltage_register always return correct register
  regulator: s5m8767: Check pdata->buck[2|3|4]_gpiodvs earlier
  regulator: tps65910: Provide settling time for DCDC voltage change
  regulator: Add Anatop regulator driver
  regulator: Simplify implementation of tps65912_get_voltage_dcdc
  regulator: Use tps65912_set_voltage_sel for both DCDCx and LDOx
  regulator: tps65910: Provide settling time for enabling rails
  regulator: max8925: Use DIV_ROUND_UP macro
  regulator: tps65912: Use simple equations to get register address
  regulator: Fix the logic of tps65910_get_mode
  regulator: Merge tps65217_pmic_ldo234_ops and tps65217_pmic_dcdc_ops to tps65217_pmic_ops
  regulator: Use DIV_ROUND_CLOSEST in wm8350_isink_get_current
  regulator: Use array to store dcdc_range settings for tps65912
  regulator: Rename s5m8767_convert_voltage to s5m8767_convert_voltage_to_sel
  regulator: tps6524x: Remove unneeded comment for N_REGULATORS
  regulator: Rename set_voltage_sel callback function name to *_sel
  regulator: Fix s5m8767_set_voltage_time_sel calculation value
  ...

Pull InfiniBand/RDMA changes for the 3.4 merge window from Roland Dreier:
 "Nothing big really stands out; by patch count lots of fixes to the
  mlx4 driver plus some cleanups and fixes to the core and other
  drivers."

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (28 commits)
  mlx4_core: Scale size of MTT table with system RAM
  mlx4_core: Allow dynamic MTU configuration for IB ports
  IB/mlx4: Fix info returned when querying IBoE ports
  IB/mlx4: Fix possible missed completion event
  mlx4_core: Report thermal error events
  mlx4_core: Fix one more static exported function
  IB: Change CQE "csum_ok" field to a bit flag
  RDMA/iwcm: Reject connect requests if cmid is not in LISTEN state
  RDMA/cxgb3: Don't pass irq flags to flush_qp()
  mlx4_core: Get rid of redundant ext_port_cap flags
  RDMA/ucma: Fix AB-BA deadlock
  IB/ehca: Fix ilog2() compile failure
  IB: Use central enum for speed instead of hard-coded values
  IB/iser: Post initial receive buffers before sending the final login request
  IB/iser: Free IB connection resources in the proper place
  IB/srp: Consolidate repetitive sysfs code
  IB/srp: Use pr_fmt() and pr_err()/pr_warn()
  IB/core: Fix SDR rates in sysfs
  mlx4: Enforce device max FMR maps in FMR alloc
  IB/mlx4: Set bad_wr for invalid send opcode
  ...

Pull SPI changes for v3.4 from Grant Likely:
 "Mostly a bunch of new drivers and driver bug fixes; but this also
  includes a few patches that create a core message queue infrastructure
  for the spi subsystem instead of making each driver open code it."

* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
  spi/fsl-espi: Make sure pm is within 2..32
  spi/fsl-espi: make the clock computation easier to read
  spi: sh-hspi: modify write/read method
  spi: sh-hspi: control spi clock more correctly
  spi: sh-hspi: convert to using core message queue
  spi: s3c64xx: Fix build
  spi: s3c64xx: remove unnecessary callback msg->complete
  spi: remove redundant variable assignment
  spi: release lock on error path in spi_pump_messages()
  spi: Compatibility with direction which is used in samsung DMA operation
  spi-topcliff-pch: add recovery processing in case wait-event timeout
  spi-topcliff-pch: supports a spi mode setup and bit order setup by IO control
  spi-topcliff-pch: Fix issue for transmitting over 4KByte
  spi-topcliff-pch: Modify pci-bus number dynamically to get DMA device info
  spi/imx: simplify error handling to free gpios
  spi: Convert to DEFINE_PCI_DEVICE_TABLE
  spi: add Broadcom BCM63xx SPI controller driver
  SPI: add CSR SiRFprimaII SPI controller driver
  spi-topcliff-pch: fix -Wuninitialized warning
  spi: Mark spi_register_board_info() __devinit
  ...

Pull core device tree changes for Linux v3.4 from Grant Likely:
 "This branch contains a minor documentation addition, a utility
  function for parsing string properties needed by some of the new ARM
  platforms, disables dynamic DT code that isn't used anywhere but on a
  few PPC machines, and exports DT node compatible data to userspace via
  UEVENT properties.  Nothing earth shattering here."

* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  of: Only compile OF_DYNAMIC on PowerPC pseries and iseries
  arm/dts: OMAP3: Add omap3evm and am335xevm support
  drivercore: Output common devicetree information in uevent
  of: Add of_property_match_string() to find index into a string list

Pull irq_domain support for all architectures from Grant Likely:
 "Generialize powerpc's irq_host as irq_domain

  This branch takes the PowerPC irq_host infrastructure (reverse mapping
  from Linux IRQ numbers to hardware irq numbering), generalizes it,
  renames it to irq_domain, and makes it available to all architectures.

  Originally the plan has been to create an all-new irq_domain
  implementation which addresses some of the powerpc shortcomings such
  as not handling 1:1 mappings well, but doing that proved to be far
  more difficult and invasive than generalizing the working code and
  refactoring it in-place.  So, this branch rips out the 'new'
  irq_domain and replaces it with the modified powerpc version (in a
  fully bisectable way of course).  It converts all users over to the
  new API and makes irq_domain selectable on any architecture.

  No architecture is forced to enable irq_domain, but the infrastructure
  is required for doing OpenFirmware style irq translations.  It will
  even work on SPARC even though SPARC has it's own mechanism for
  translating irqs at boot time.  MIPS, microblaze, embedded x86 and c6x
  are converted too.

  The resulting irq_domain code is probably still too verbose and can be
  optimized more, but that can be done incrementally and is a task for
  follow-on patches."

* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
  dt: fix twl4030 for non-dt compile on x86
  mfd: twl-core: Add IRQ_DOMAIN dependency
  devicetree: Add empty of_platform_populate() for !CONFIG_OF_ADDRESS (sparc)
  irq_domain: Centralize definition of irq_dispose_mapping()
  irq_domain/mips: Allow irq_domain on MIPS
  irq_domain/x86: Convert x86 (embedded) to use common irq_domain
  ppc-6xx: fix build failure in flipper-pic.c and hlwd-pic.c
  irq_domain/microblaze: Convert microblaze to use irq_domains
  irq_domain/powerpc: Replace custom xlate functions with library functions
  irq_domain/powerpc: constify irq_domain_ops
  irq_domain/c6x: Use library of xlate functions
  irq_domain/c6x: constify irq_domain structures
  irq_domain/c6x: Convert c6x to use generic irq_domain support.
  irq_domain: constify irq_domain_ops
  irq_domain: Create common xlate functions that device drivers can use
  irq_domain: Remove irq_domain_add_simple()
  irq_domain: Remove 'new' irq_domain in favour of the ppc one
  mfd: twl-core.c: Fix the number of interrupts managed by twl4030
  of/address: add empty static inlines for !CONFIG_OF
  irq_domain: Add support for base irq and hwirq in legacy mappings
  ...

Pull power management updates for 3.4 from Rafael Wysocki:
 "Assorted extensions and fixes including:

  * Introduction of early/late suspend/hibernation device callbacks.
  * Generic PM domains extensions and fixes.
  * devfreq updates from Axel Lin and MyungJoo Ham.
  * Device PM QoS updates.
  * Fixes of concurrency problems with wakeup sources.
  * System suspend and hibernation fixes."

* tag 'pm-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (43 commits)
  PM / Domains: Check domain status during hibernation restore of devices
  PM / devfreq: add relation of recommended frequency.
  PM / shmobile: Make MTU2 driver use pm_genpd_dev_always_on()
  PM / shmobile: Make CMT driver use pm_genpd_dev_always_on()
  PM / shmobile: Make TMU driver use pm_genpd_dev_always_on()
  PM / Domains: Introduce "always on" device flag
  PM / Domains: Fix hibernation restore of devices, v2
  PM / Domains: Fix handling of wakeup devices during system resume
  sh_mmcif / PM: Use PM QoS latency constraint
  tmio_mmc / PM: Use PM QoS latency constraint
  PM / QoS: Make it possible to expose PM QoS latency constraints
  PM / Sleep: JBD and JBD2 missing set_freezable()
  PM / Domains: Fix include for PM_GENERIC_DOMAINS=n case
  PM / Freezer: Remove references to TIF_FREEZE in comments
  PM / Sleep: Add more wakeup source initialization routines
  PM / Hibernate: Enable usermodehelpers in hibernate() error path
  PM / Sleep: Make __pm_stay_awake() delete wakeup source timers
  PM / Sleep: Fix race conditions related to wakeup source timer function
  PM / Sleep: Fix possible infinite loop during wakeup source destruction
  PM / Hibernate: print physical addresses consistently with other parts of kernel
  ...

Pull kmap_atomic cleanup from Cong Wang.

It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().

Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.

* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
  feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
  highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
  drbd: remove the second argument of k[un]map_atomic()
  zcache: remove the second argument of k[un]map_atomic()
  gma500: remove the second argument of k[un]map_atomic()
  dm: remove the second argument of k[un]map_atomic()
  tomoyo: remove the second argument of k[un]map_atomic()
  sunrpc: remove the second argument of k[un]map_atomic()
  rds: remove the second argument of k[un]map_atomic()
  net: remove the second argument of k[un]map_atomic()
  mm: remove the second argument of k[un]map_atomic()
  lib: remove the second argument of k[un]map_atomic()
  power: remove the second argument of k[un]map_atomic()
  kdb: remove the second argument of k[un]map_atomic()
  udf: remove the second argument of k[un]map_atomic()
  ubifs: remove the second argument of k[un]map_atomic()
  squashfs: remove the second argument of k[un]map_atomic()
  reiserfs: remove the second argument of k[un]map_atomic()
  ocfs2: remove the second argument of k[un]map_atomic()
  ntfs: remove the second argument of k[un]map_atomic()
  ...

Pull trivial tree from Jiri Kosina:
 "It's indeed trivial -- mostly documentation updates and a bunch of
  typo fixes from Masanari.

  There are also several linux/version.h include removals from Jesper."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
  kcore: fix spelling in read_kcore() comment
  constify struct pci_dev * in obvious cases
  Revert "char: Fix typo in viotape.c"
  init: fix wording error in mm_init comment
  usb: gadget: Kconfig: fix typo for 'different'
  Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
  writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
  writeback: fix typo in the writeback_control comment
  Documentation: Fix multiple typo in Documentation
  tpm_tis: fix tis_lock with respect to RCU
  Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
  Doc: Update numastat.txt
  qla4xxx: Add missing spaces to error messages
  compiler.h: Fix typo
  security: struct security_operations kerneldoc fix
  Documentation: broken URL in libata.tmpl
  Documentation: broken URL in filesystems.tmpl
  mtd: simplify return logic in do_map_probe()
  mm: fix comment typo of truncate_inode_pages_range
  power: bq27x00: Fix typos in comment
  ...

Pull HID updates from Jiri Kosina:
 "It contains HID driver updates all over the place -- a lot of new
  hardware support especially in the multitouch area, including generic
  handling of all multitouch devices by the hid-multitiouch driver
  automatically."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (42 commits)
  HID: multitouch: add PID for Fructel product
  HID: wacom: Add reporting of wheel for Intuos4 WL
  HID: wacom: Replace __set_bit with input_set_capability
  HID: tivo: add support for BT-version (0x1200)
  HID: wacom: Reset stylus buttons - Intuos4 WL
  HID: multitouch: detect serial protocol
  HID: handle all multitouch devices through hid-multitouch
  HID: multitouch: fix handling of buggy reports descriptors for Dell ST2220T
  HID: make it possible to force hid-core claim the device
  HID: multitouch: add support for eGalax 0x722a
  HID: usbhid: add quirk no_get for quanta 3008 devices
  HID: multitouch: add more eGalax devices
  HID: multitouch: add new PID from Ideacom
  HID: multitouch: add support for Atmel maXTouch 03eb:2118
  HID: waltop: Add support for tablet with PID 0038
  HID: waltop: Replace original rdescs with links
  HID: uclogic: Replace original rdescs with links
  HID: wacom: Add pad buttons reporting on Intuos4 WL
  HID: wacom: report distance for Intuos4 WL
  HID: kye: Add support for 3 tablets
  ...

Pull networking merge from David Miller:
 "1) Move ixgbe driver over to purely page based buffering on receive.
     From Alexander Duyck.

  2) Add receive packet steering support to e1000e, from Bruce Allan.

  3) Convert TCP MD5 support over to RCU, from Eric Dumazet.

  4) Reduce cpu usage in handling out-of-order TCP packets on modern
     systems, also from Eric Dumazet.

  5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
     folks happy, from Erich Hoover.

  6) Support VLAN trunking from guests in hyperv driver, from Haiyang
     Zhang.

  7) Support byte-queue-limtis in r8169, from Igor Maravic.

  8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
     was never properly implemented, Jiri Benc fixed that.

  9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.

  10) Support kernel side dump filtering by ctmark in netfilter
      ctnetlink, from Pablo Neira Ayuso.

  11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.

  12) Add new peek socket options to assist with socket migration, from
      Pavel Emelyanov.

  13) Add sch_plug packet scheduler whose queue is controlled by
      userland daemons using explicit freeze and release commands.  From
      Shriram Rajagopalan.

  14) Fix FCOE checksum offload handling on transmit, from Yi Zou."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
  Fix pppol2tp getsockname()
  Remove printk from rds_sendmsg
  ipv6: fix incorrent ipv6 ipsec packet fragment
  cpsw: Hook up default ndo_change_mtu.
  net: qmi_wwan: fix build error due to cdc-wdm dependecy
  netdev: driver: ethernet: Add TI CPSW driver
  netdev: driver: ethernet: add cpsw address lookup engine support
  phy: add am79c874 PHY support
  mlx4_core: fix race on comm channel
  bonding: send igmp report for its master
  fs_enet: Add MPC5125 FEC support and PHY interface selection
  net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
  net: update the usage of CHECKSUM_UNNECESSARY
  fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
  net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
  ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
  net/hyperv: Fix the code handling tx busy
  ixgbe: fix namespace issues when FCoE/DCB is not enabled
  rtlwifi: Remove unused ETH_ADDR_LEN defines
  igbvf: Use ETH_ALEN
  ...

Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.

Pull workqueue changes from Tejun Heo:
 "This contains only one commit which cleans up UP allocation path a
  bit."

* 'for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: use percpu allocator for cwq on UP

Pull cgroup changes from Tejun Heo:
 "Out of the 8 commits, one fixes a long-standing locking issue around
  tasklist walking and others are cleanups."

* 'for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: Walk task list under tasklist_lock in cgroup_enable_task_cg_list
  cgroup: Remove wrong comment on cgroup_enable_task_cg_list()
  cgroup: remove cgroup_subsys argument from callbacks
  cgroup: remove extra calls to find_existing_css_set
  cgroup: replace tasklist_lock with rcu_read_lock
  cgroup: simplify double-check locking in cgroup_attach_proc
  cgroup: move struct cgroup_pidlist out from the header file
  cgroup: remove cgroup_attach_task_current_cg()

Minor cleanup. de_thread()->setmax_mm_hiwater_rss() looks a bit
strange, move it into exec_mmap() which plays with old_mm.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exit_notify() changes ->exit_signal if the parent already did exec.
This doesn't really work, we are not going to send the signal now
if there is another live thread or the exiting task is traced. The
parent can exec before the last dies or the tracer detaches.

Move this check into do_notify_parent() which actually sends the
signal.

The user-visible change is that we do not change ->exit_signal,
and thus the exiting task is still "clone children" for
do_wait()->eligible_child(__WCLONE). Hopefully this is fine, the
current logic is racy anyway.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exit_notify() checks "tsk->self_exec_id != tsk->parent_exec_id"
to handle the "we have changed execution domain" case.

We can change do_thread() to always set ->exit_signal = SIGCHLD
and remove this check to simplify the code.

We could change setup_new_exec() instead, this looks more logical
because it increments ->self_exec_id. But note that de_thread()
already resets ->exit_signal if it changes the leader, let's keep
both changes close to each other.

Note that we change ->exit_signal lockless, this changes the rules.
Thereafter ->exit_signal is not stable under tasklist but this is
fine, the only possible change is OLDSIG -> SIGCHLD. This can race
with eligible_child() but the race is harmless. We can race with
reparent_leader() which changes our ->exit_signal in parallel, but
it does the same change to SIGCHLD.

The noticeable user-visible change is that the execing task is not
"visible" to do_wait()->eligible_child(__WCLONE) right after exec.
To me this looks more logical, and this is consistent with mt case.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The child must not control its ->exit_signal, it is the parent who
decides which signal the child should use for notification.

This means that CLONE_PARENT should not use "clone_flags & CSIGNAL",
the forking task is the sibling of the new process and their parent
doesn't control exit_signal in this case.

This patch uses ->exit_signal of the forking process, but perhaps
we should simply use SIGCHLD.

We read group_leader->exit_signal lockless, this can race with the
ORIGINAL_SIGNAL -> SIGCHLD transition, but this is fine.

Potentially this change allows to kill self_exec_id/parent_exec_id.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

While testing L2TP functionality, I came across a bug in getsockname().  The
IP address returned within the pppol2tp_addr's addr memember was not being
set to the IP  address in use.  This bug is caused by using inet_sk() on the
wrong socket (the L2TP socket rather than the underlying UDP socket), and was
likely introduced during the addition of L2TPv3 support.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

no socket layer outputs a message for this error and neither should rds.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull USB merge for 3.4-rc1 from Greg KH:
 "Here's the big USB merge for the 3.4-rc1 merge window.

  Lots of gadget driver reworks here, driver updates, xhci changes, some
  new drivers added, usb-serial core reworking to fix some bugs, and
  other various minor things.

  There are some patches touching arch code, but they have all been
  acked by the various arch maintainers."

* tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (302 commits)
  net: qmi_wwan: add support for ZTE MF820D
  USB: option: add ZTE MF820D
  usb: gadget: f_fs: Remove lock is held before freeing checks
  USB: option: make interface blacklist work again
  usb/ub: deprecate & schedule for removal the "Low Performance USB Block" driver
  USB: ohci-pxa27x: add clk_prepare/clk_unprepare calls
  USB: use generic platform driver on ath79
  USB: EHCI: Add a generic platform device driver
  USB: OHCI: Add a generic platform device driver
  USB: ftdi_sio: new PID: LUMEL PD12
  USB: ftdi_sio: add support for FT-X series devices
  USB: serial: mos7840: Fixed MCS7820 device attach problem
  usb: Don't make USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.
  usb gadget: fix a section mismatch when compiling g_ffs with CONFIG_USB_FUNCTIONFS_ETH
  USB: ohci-nxp: Remove i2c_write(), use smbus
  USB: ohci-nxp: Support for LPC32xx
  USB: ohci-nxp: Rename symbols from pnx4008 to nxp
  USB: OHCI-HCD: Rename ohci-pnx4008 to ohci-nxp
  usb: gadget: Kconfig: fix typo for 'different'
  usb: dwc3: pci: fix another failure path in dwc3_pci_probe()
  ...

Pull TTY/serial patches from Greg KH:
 "tty and serial merge for 3.4-rc1

  Here's the big serial and tty merge for the 3.4-rc1 tree.

  There's loads of fixes and reworks in here from Jiri for the tty
  layer, and a number of patches from Alan to help try to wrestle the vt
  layer into a sane model.

  Other than that, lots of driver updates and fixes, and other minor
  stuff, all detailed in the shortlog."

* tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (132 commits)
  serial: pxa: add clk_prepare/clk_unprepare calls
  TTY: Wrong unicode value copied in con_set_unimap()
  serial: PL011: clear pending interrupts
  serial: bfin-uart: Don't access tty circular buffer in TX DMA interrupt after it is reset.
  vt: NULL dereference in vt_do_kdsk_ioctl()
  tty: serial: vt8500: fix annotations for probe/remove
  serial: remove back and forth conversions in serial_out_sync
  serial: use serial_port_in/out vs serial_in/out in 8250
  serial: introduce generic port in/out helpers
  serial: reduce number of indirections in 8250 code
  serial: delete useless void casts in 8250.c
  serial: make 8250's serial_in shareable to other drivers.
  serial: delete last unused traces of pausing I/O in 8250
  pch_uart: Add module parameter descriptions
  pch_uart: Use existing default_baud in setup_console
  pch_uart: Add user_uartclk parameter
  pch_uart: Add Fish River Island II uart clock quirks
  pch_uart: Use uartclk instead of base_baud
  mpc5200b/uart: select more tolerant uart prescaler on low baudrates
  tty: moxa: fix bit test in moxa_start()
  ...