Skip to content

L
linux
Switch branch/tag
  1. 13 Sep, 2019 30 commits
  3. 12 Sep, 2019 5 commits
  5. 11 Sep, 2019 5 commits
    • Dirk van der Merwe's avatar
      nfp: read chip model from the PluDevice register · 421bceb2
      Dirk van der Merwe authored 
      The PluDevice register provides the authoritative chip model/revision.

Since the model number is purely used for reporting purposes, follow
the hardware team convention of subtracting 0x10 from the PluDevice
register to obtain the chip model/revision number.
Suggested-by: default avatarFrancois H. Theron <francois.theron@netronome.com>
Signed-off-by: default avatarDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: default avatarSimon Horman <simon.horman@netronome.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      421bceb2
    • Eric Dumazet's avatar
      tcp: force a PSH flag on TSO packets · 051ba674
      Eric Dumazet authored 
      When tcp sends a TSO packet, adding a PSH flag on it
reduces the sojourn time of GRO packet in GRO receivers.

This is particularly the case under pressure, since RX queues
receive packets for many concurrent flows.

A sender can give a hint to GRO engines when it is
appropriate to flush a super-packet, especially when pacing
is in the picture, since next packet is probably delayed by
one ms.

Having less packets in GRO engine reduces chance
of LRU eviction or inflated RTT, and reduces GRO cost.

We found recently that we must not set the PSH flag on
individual full-size MSS segments [1] :

 Under pressure (CWR state), we better let the packet sit
 for a small delay (depending on NAPI logic) so that the
 ACK packet is delayed, and thus next packet we send is
 also delayed a bit. Eventually the bottleneck queue can
 be drained. DCTCP flows with CWND=1 have demonstrated
 the issue.

This patch allows to slowdown the aggregate traffic without
involving high resolution timers on senders and/or
receivers.

It has been used at Google for about four years,
and has been discussed at various networking conferences.

[1] segments smaller than MSS already have PSH flag set
    by tcp_sendmsg() / tcp_mark_push(), unless MSG_MORE
    has been requested by the user.
Signed-off-by: default avatarEric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tariq Toukan <tariqt@mellanox.com>
Acked-by: default avatarSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: default avatarNeal Cardwell <ncardwell@google.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      051ba674
    • Stefano Brivio's avatar
      ipv6: Don't use dst gateway directly in ip6_confirm_neigh() · cbfd6891
      Stefano Brivio authored 
      This is the equivalent of commit 2c6b55f4 ("ipv6: fix neighbour
resolution with raw socket") for ip6_confirm_neigh(): we can send a
packet with MSG_CONFIRM on a raw socket for a connected route, so the
gateway would be :: here, and we should pick the next hop using
rt6_nexthop() instead.

This was found by code review and, to the best of my knowledge, doesn't
actually fix a practical issue: the destination address from the packet
is not considered while confirming a neighbour, as ip6_confirm_neigh()
calls choose_neigh_daddr() without passing the packet, so there are no
similar issues as the one fixed by said commit.

A possible source of issues with the existing implementation might come
from the fact that, if we have a cached dst, we won't consider it,
while rt6_nexthop() takes care of that. I might just not be creative
enough to find a practical problem here: the only way to affect this
with cached routes is to have one coming from an ICMPv6 redirect, but
if the next hop is a directly connected host, there should be no
topology for which a redirect applies here, and tests with redirected
routes show no differences for MSG_CONFIRM (and MSG_PROBE) packets on
raw sockets destined to a directly connected host.

However, directly using the dst gateway here is not consistent anymore
with neighbour resolution, and, in general, as we want the next hop,
using rt6_nexthop() looks like the only sane way to fetch it.
Reported-by: default avatarGuillaume Nault <gnault@redhat.com>
Signed-off-by: default avatarStefano Brivio <sbrivio@redhat.com>
Acked-by: default avatarGuillaume Nault <gnault@redhat.com>
Acked-by: default avatarNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      cbfd6891
    • Jose Abreu's avatar
      net: stmmac: pci: Add HAPS support using GMAC5 · ebecb860
      Jose Abreu authored 
      Add the support for Synopsys HAPS board that uses GMAC5.
Signed-off-by: default avatarJose Abreu <joabreu@synopsys.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      ebecb860
    • Vitaly Gaiduk's avatar
      net: phy: dp83867: Add SGMII mode type switching · 507ddd5c
      Vitaly Gaiduk authored 
      This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Signed-off-by: default avatarVitaly Gaiduk <vitaly.gaiduk@cloudbear.ru>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      507ddd5c
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7