Prior to suspending the system, we need to ensure that certain
clock source and gate registers are unmasked.

while at it, add these clks to save/restore list also.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

Array of struct of_device_id may be be const as expected by
of_match_table field and of_find_matching_node_and_match() function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

Enable ARMCLK down feature on Exynos3250 SoC. The frequency of
ARMCLK will be reduced upon entering idle mode (WFI or WFE).

The feature behaves like very fast cpufreq ondemand governor.

The patch uses simillar settings as Exynos5250 (clk-exynos5250.c),
except it disables clock up feature.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

Enable ARMCLK down feature on all Exynos4 SoCs. The frequency of
ARMCLK will be reduced upon entering idle mode (WFI or WFE).

The feature behaves like very fast cpufreq ondemand governor. In idle
mode this reduces energy consumption on full frequency chosen by
cpufreq governor by approximately:
 - Trats2:  6.5% (153 mA -> 143 mA)
 - Trats:  33.0% (180 mA -> 120 mA)
 - Gear1:  27.0% (180 mA -> 130 mA)

The patch uses simillar settings as Exynos5250 (clk-exynos5250.c),
except it disables clock up feature and on Exynos4412 ARMCLK down is
enabled for all 4 cores.

Tested on Trats board (Exynos4210), Trats2 board (Exynos4412) and
Samsung Gear 1 (Exynos4212).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

This patch extends nodes of PMU system controller on Exynos4210, 4x12,
5250 and 5420 SoCs with newly defined properties used by Exynos CLKOUT
driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

This patch introduces a driver that handles configuration of CLKOUT pin
of Exynos SoCs that can be used to output certain clocks from inside of
the SoC to a dedicated output pin.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

This patch adds definitions of clocks that are used to drive clock
output signals of particular CMU sub-blocks that are then fed to PMU and
handled by Exynos CLKOUT driver added in further patch.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

This patch adds missing definitions of clocks from CPU and DMC clock
domains, which are necessary to properly represent CLKOUT clock hierarchy
added in further patch.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

Exynos4 has saveral PPMUs and each of them has operation clock which
can be gated through CMU's SFR control.

New clocks are listed below. All clocks are added as a gate-typed clock.

CLK_PPMULEFT, CLK_PPMURIGHT, CLK_PPMUCAMIF, CLK_PPMUTV, CLK_PPMUMFC_L,
CLK_PPMUMFC_R, CLK_G3D, CLK_PPMUIMAGE, CLK_PPMULCD0, CLK_PPMULCD1,
CLK_PPMUFILE, CLK_PPMUGPS, CLK_PPMUDMC0, CLK_PPMUDMC1, CLK_PPMUCPU,
CLK_PPMUACP,
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

Ensure the clock provider is not registered until after all its related
clocks were created and are ready to use. Currently there are races
possible and any (of_)clk_get() call right after a clock provider's
clk_init_cb callback call may fail.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

The "aclk66_peric" clock is a gate clock with a whole bunch of gates
underneath it.  This big gate isn't very useful to include in our
clock tree.  If any of the children need to be turned on then the big
gate will need to be on anyway.  ...and there are plenty of other "big
gates" that aren't described in our clock tree, some of which shut off
collections of clocks that have no relationship in the hierarchy so
are hard to model.

"aclk66_peric" is causing earlyprintk problems since it gets disabled
as part of the boot process, so let's just remove it.

Strangely (and for no good reason) this clock is exported as part of
the common clock bindings.  Remove it since there are no in-kernel
device trees using it and no reason anyone out of tree should refer to
it either.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

Change bit from 2 to 9 for tv (mixer) sysmmu clock.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

In the move to this clock driver the hookups for the SPI clocks were
dropped, which causes my system Cragganmore (s3c6410 based) to be unable
to locate any spibus clocks. This patch adds them back in.

When taking the clock from the epll clock (SCLK) the rates on the SPI
bus are incorrect, this needs further debugging but the hookup here
should be correct and the problem should be else where.

The USBCLK case has been dropped because this requires the USB PHY to be
enabled.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

ISP special clocks have dedicated gating registers and so MUX SRC_MASK
register should not be used. This patch fixes the problem of
Exynos4x12-based boards freezing on system suspend, because those
mux outputs need not to be masked while suspending.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>

Without these aliases clock lookup fails in s3c2410fb,
s3cmci, s3c2410-nand, s3c24xx-i2s, and i2c-s3c2410 drivers.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

There's a several typos in a driver: 2410 instead of S3C2410
and wrong argument to ARRAY_SIZE(). They prevent s3c2410
from properly booting.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>

This patch flattens the clk tree in CCF debugfs. Instead of representing the
clocks and their hierarchy as a directory structure under
/sys/kernel/debug/clk, each clock gets a single directory directly under
/sys/kernel/debug/clk. The orphans directory is replaced by a file called
clk_orphan_summary.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

This error message can spam the logs if you have lots of probe
deferals due to missing clocks. Just silence the error in this
case because the driver should try again later.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

Pull i2c new drivers from Wolfram Sang:
 "Here is a pull request from i2c hoping for the "new driver" rule.

  Originally, I wanted to send this request during the merge window, but
  code checkers with very recent additions complained, so a few fixups
  were needed.  So, some more time went by and I merged rc1 to get a
  stable base"

So the "new driver" rule is really about drivers that people absolutely
need for the kernel to work on new hardware, which is not so much the
case for i2c.  So I considered not pulling this, but eventually
relented.

Just for FYI: the whole (and only) point of "new drivers" is not that
new drivers cannot regress things (they can, and they have - by
triggering badly tested code on machines that never triggered that code
before), but because they can bring to life machines that otherwise
wouldn't be useful at all without the drivers.

So the new driver rule is for essential things that actual consumers
would care about, ie devices like networking or disk drivers that matter
to normal people (not server people - they run old kernels anyway, so
mainlining new drivers is irrelevant for them).

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: sun6-p2wi: fix call to snprintf
  i2c: rk3x: add NULL entry to the end of_device_id array
  i2c: sun6i-p2wi: use proper return value in probe
  i2c: sunxi: add P2WI (Push/Pull 2 Wire Interface) controller support
  i2c: sunxi: add P2WI DT bindings documentation
  i2c: rk3x: add driver for Rockchip RK3xxx SoC I2C adapter

Pull file locking fixes from Jeff Layton:
 "File locking related bugfixes

  Nothing too earth-shattering here.  A fix for a potential regression
  due to a patch in pile #1, and the addition of a memory barrier to
  prevent a race condition between break_deleg and generic_add_lease"

* tag 'locks-v3.16-2' of git://git.samba.org/jlayton/linux:
  locks: set fl_owner for leases back to current->files
  locks: add missing memory barrier in break_deleg

Pull kbuild fixes from Michal Marek:
 "There are three fixes for regressions caused by the relative paths
  series: deb-pkg, tar-pkg and *docs did not work with O=.

  Plus, there is a fix for the linux-headers deb package and a fixed
  typo.  These are not regression fixes but are safe enough"

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kbuild: fix a typo in a kbuild document
  builddeb: fix missing headers in linux-headers package
  Documentation: Fix DocBook build with relative $(srctree)
  kbuild: Fix tar-pkg with relative $(objtree)
  deb-pkg: Fix for relative paths

Pull btrfs fixes from Chris Mason:
 "This fixes some lockups in btrfs reported with rc1.  It probably has
  some performance impact because it is backing off our spinning locks
  more often and switching to a blocking lock.  I'll be able to nail
  that down next week, but for now I want to get the lockups taken care
  of.

  Otherwise some more stack reduction and assorted fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix wrong error handle when the device is missing or is not writeable
  Btrfs: fix deadlock when mounting a degraded fs
  Btrfs: use bio_endio_nodec instead of open code
  Btrfs: fix NULL pointer crash when running balance and scrub concurrently
  btrfs: Skip scrubbing removed chunks to avoid -ENOENT.
  Btrfs: fix broken free space cache after the system crashed
  Btrfs: make free space cache write out functions more readable
  Btrfs: remove unused wait queue in struct extent_buffer
  Btrfs: fix deadlocks with trylock on tree nodes

Pull nfsd bugfixes from Bruce Fields:
 "Fixes for a new regression from the xdr encoding rewrite, and a
  delegation problem we've had for a while (made somewhat more annoying
  by the vfs delegation support added in 3.13)"

* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
  NFSD: fix bug for readdir of pseudofs
  NFSD: Don't hand out delegations for 30 seconds after recalling them.

Pull perf fixes from Ingo Molnar:
 "This is larger than usual: the main reason are the ARM symbol lookup
  speedups that came in late and were hard to resist.

  There's also a kprobes fix and various tooling fixes, plus the minimal
  re-enablement of the mmap2 support interface"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
  x86/kprobes: Fix build errors and blacklist context_track_user
  perf tests: Add test for closing dso objects on EMFILE error
  perf tests: Add test for caching dso file descriptors
  perf tests: Allow reuse of test_file function
  perf tests: Spawn child for each test
  perf tools: Add dso__data_* interface descriptons
  perf tools: Allow to close dso fd in case of open failure
  perf tools: Add file size check and factor dso__data_read_offset
  perf tools: Cache dso data file descriptor
  perf tools: Add global count of opened dso objects
  perf tools: Add global list of opened dso objects
  perf tools: Add data_fd into dso object
  perf tools: Separate dso data related variables
  perf tools: Cache register accesses for unwind processing
  perf record: Fix to honor user freq/interval properly
  perf timechart: Reflow documentation
  perf probe: Improve error messages in --line option
  perf probe: Improve an error message of perf probe --vars mode
  perf probe: Show error code and description in verbose mode
  perf probe: Improve error message for unknown member of data structure
  ...

Merge branch 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull rtmutex fixes from Thomas Gleixner:
 "Another three patches to make the rtmutex code more robust.  That's
  the last urgent fallout from the big futex/rtmutex investigation"

* 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rtmutex: Plug slow unlock race
  rtmutex: Detect changes in the pi lock chain
  rtmutex: Handle deadlock detection smarter

Pull s390 patches from Martin Schwidefsky:
 "A couple of bug fixes, a debug change for qdio, an update for the
  default config, and one small extension.

  The watchdog module based on diagnose 0x288 is converted to the
  watchdog API and it now works under LPAR as well"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/ccwgroup: use ccwgroup_ungroup wrapper
  s390/ccwgroup: fix an uninitialized return code
  s390/ccwgroup: obtain extra reference for asynchronous processing
  qdio: Keep device-specific dbf entries
  s390/compat: correct ucontext layout for high gprs
  s390/cio: set device name as early as possible
  s390: update default configuration
  s390: avoid format strings leaking into names
  s390/airq: silence lockdep warning
  s390/watchdog: add support for LPAR operation (diag288)
  s390/watchdog: use watchdog API
  s390/sclp_vt220: Enable ASCII console per default
  s390/qdio: replace shift loop by ilog2
  s390/cio: silence lockdep warning
  s390/uaccess: always load the kernel ASCE after task switch
  s390/ap_bus: Make modules parameters visible in sysfs

Pull UniCore32 bug fixes from Guan Xuetao:
 "This includes bugfixes to make unicore32 successfully build under
  defconfig, and some changes for allmodconfig (though not finished)"

* tag 'for-linus' of git://github.com/gxt/linux:
  unicore32: Remove ARCH_HAS_CPUFREQ config option
  UniCore32: Change git tree location information in MAINTAINERS
  arch: unicore32: ksyms: export '__cpuc_coherent_kern_range' to avoid compiling failure
  arch: unicore32: ksyms: export 'pm_power_off' to avoid compiling failure.
  arch: unicore32: ksyms: export additional find_first_*() to avoid compiling failure
  arch:unicore32:mm: add devmem_is_allowed() to support STRICT_DEVMEM
  unicore32: include: asm: add missing ')' for PAGE_* macros in pgtable.h
  arch/unicore32/kernel/setup.c: add generic 'screen_info' to avoid compiling failure
  drivers: scsi: mvsas: fix compiling issue by adding 'MVS_' for "enum pci_interrupt_cause"
  arch: unicore32: kernel: ksyms: remove 'bswapsi2' and 'muldi3' to avoid compiling failure
  arch/unicore32/kernel/ksyms.c: remove 2 export symbols to avoid compiling failure
  drivers/rtc/rtc-puv3.c: remove "&dev->" for typo issue MIME-Version: 1.0
  drivers/rtc/rtc-puv3.c: use dev_dbg() instead of dev_debug() for typo issue
  arch/unicore32/include/asm/io.h: add readl_relaxed() generic definition
  arch/unicore32/include/asm/ptrace.h: add generic definition for profile_pc()
  arch/unicore32/mm/alignment.c: include "asm/pgtable.h" to avoid compiling error
  arch/unicore32/kernel/clock.c: add readl() and writel() for 'PM_' macros
  arch/unicore32/kernel/module.c: use __vmalloc_node_range() instead of __vmalloc_area()
  arch/unicore32/kernel/ksyms.c: remove several undefined exported symbols

Pull char / misc driver fixes from Greg KH:
 "Here are 3 patches, one a revert of the UIO patch you objected to in
  3.16-rc1 and that no one wanted to defend, a w1 driver bugfix, and a
  MAINTAINERS update for the vmware balloon driver.

  All of these, except for the MAINTAINERS update which just got added,
  have been in linux-next just fine"

* tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  MAINTAINERS: add entry for VMware Balloon driver
  w1: mxc_w1: Fix incorrect "presence" status
  Revert "uio: fix vma io range check in mmap"

Pull staging driver fixes from Greg KH:
 "Here are a few fixes for staging and iio drivers that resolve issues
  reported in 3.16-rc1.

  All have been in linux-next just fine"

* tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  imx-drm: parallel-display: Fix DPMS default state.
  staging: android: timed_output: fix use after free of dev
  staging: comedi: addi_apci_1564: add addi_watchdog dependency
  staging: rtl8723au: Reference correct firmwarefiles with MODULE_FIRMWARE()
  staging: rtl8723au: Request correct firmware file for A-cut parts
  iio: adc: checking for NULL instead of IS_ERR() in probe
  iio: adc: at91: signedness bug in at91_adc_get_trigger_value_by_name()
  iio: mxs-lradc: fix divider
  iio: Fix endianness issue in ak8975_read_axis()
  staging/iio: IIO_SIMPLE_DUMMY_BUFFER neds IIO_BUFFER
  twl4030-madc: Request processed values in twl4030_get_madc_conversion
  staging: iio: tsl2x7x_core: fix proximity treshold
  iio: Fix two mpl3115 issues in measurement conversion
  iio: hid-sensors: Get feature report from sensor hub after changing power state

Pull tty/serial bugfixes from Greg KH:
 "Here are some tty / serial driver bugfixes for 3.16-rc2 that resolve
  some reported issues.  The samsung driver build error itself has been
  reported by a bunch of people, sorry about that one.  The others are
  all tiny and everyone seems to like them in linux-next so far"

* tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty/serial: fix 8250 early console option passing to regular console
  tty: Correct INPCK handling
  serial: Fix IGNBRK handling
  serial: samsung: Fix build error

Pull USB fixes from Greg KH:
 "Here are some USB fixes for 3.16-rc2 that resolve some reported
  issues.  All of these have been in linux-next for a while with no
  problems"

* tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: usbtest: add a timeout for scatter-gather tests
  USB: EHCI: avoid BIOS handover on the HASEE E200
  usb: fix hub-port pm_runtime_enable() vs runtime pm transitions
  usb: quiet peer failure warning, disable poweroff
  usb: improve "not suspended yet" message in hub_suspend()
  xhci: Fix sleeping with IRQs disabled in xhci_stop_device()
  usb: fix ->update_hub_device() vs hdev->maxchild

Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ACPI and power management fixes from Rafael Wysocki:
 "These are fixes mostly (ia64 regression related to the ACPI
  enumeration of devices, cpufreq regressions, fix for I2C controllers
  included in Intel SoCs, mvebu cpuidle driver fix related to sysfs)
  plus additional kernel command line arguments from Kees to make it
  possible to build kernel images with hibernation and the kernel
  address space randomization included simultaneously, a new ACPI
  battery driver quirk for a system with a broken BIOS and a couple of
  ACPI core cleanups.

  Specifics:

   - Fix for an ia64 regression introduced during the 3.11 cycle by a
     commit that modified the hardware initialization ordering and made
     device discovery fail on some systems.

   - Fix for a build problem on systems where the cpufreq-cpu0 driver is
     built-in and the cpu-thermal driver is modular from Arnd Bergmann.

   - Fix for a recently introduced computational mistake in the
     intel_pstate driver that leads to excessive rounding errors from
     Doug Smythies.

   - Fix for a failure code path in cpufreq_update_policy() that fails
     to unlock the locks acquired previously from Aaron Plattner.

   - Fix for the cpuidle mvebu driver to use shorter state names which
     will prevent the sysfs interface from returning mangled strings.
     From Gregory Clement.

   - ACPI LPSS driver fix to make sure that the I2C controllers included
     in BayTrail SoCs are not held in the reset state while they are
     being probed from Mika Westerberg.

   - New kernel command line arguments making it possible to build
     kernel images with hibernation and kASLR included at the same time
     and to select which of them will be used via the command line (they
     are still functionally mutually exclusive, though).  From Kees
     Cook.

   - ACPI battery driver quirk for Acer Aspire V5-573G that fails to
     send battery status change notifications timely from Alexander
     Mezin.

   - Two ACPI core cleanups from Christoph Jaeger and Fabian Frederick"

* tag 'pm+acpi-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: mvebu: Fix the name of the states
  cpufreq: unlock when failing cpufreq_update_policy()
  intel_pstate: Correct rounding in busy calculation
  ACPI: use kstrto*() instead of simple_strto*()
  ACPI / processor replace __attribute__((packed)) by __packed
  ACPI / battery: add quirk for Acer Aspire V5-573G
  ACPI / battery: use callback for setting up quirks
  ACPI / LPSS: Take I2C host controllers out of reset
  x86, kaslr: boot-time selectable with hibernation
  PM / hibernate: introduce "nohibernate" boot parameter
  cpufreq: cpufreq-cpu0: fix CPU_THERMAL dependency
  ACPI / ia64 / sba_iommu: Restore the working initialization ordering

Pull sound fixes from Takashi Iwai:
 "The significant part here is a few security fixes for ALSA core
  control API by Lars.  Besides that, there are a few fixes for ASoC
  sigmadsp (again by Lars) for building properly, and small fixes for
  ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
  i915/HD-audio binding"

* tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: control: Make sure that id->index does not overflow
  ALSA: control: Handle numid overflow
  ALSA: control: Don't access controls outside of protected regions
  ALSA: control: Fix replacing user controls
  ALSA: control: Protect user controls against concurrent access
  drm/i915, HD-audio: Don't continue probing when nomodeset is given
  ASoC: fsl: Fix build problem
  ASoC: rsnd: fixup index of src/dst mod when capture
  ASoC: fsl_spdif: Fix integer overflow when calculating divisors
  ASoC: fsl_spdif: Fix incorrect usage of regmap_read()
  ASoC: dapm: Make sure register value is in sync with DAPM kcontrol state
  ASoC: sigmadsp: Split regmap and I2C support into separate modules
  ASoC: MMP audio needs sram support
  ASoC: pxa: add I2C dependencies as needed

Pull drm fixes from Dave Airlie:
 "This looks bigger than it is, as one of the nouveau firmware fixes
  ("drm/gf100-/gr: report class data to host on fwmthd failure")
  regenerates a bunch of the firmware files after changing the assembly
  by a few lines, without that, its more of a

    36 files changed, 370 insertions(+), 129 deletions(-)

  It contains some vt.c fixes acked by Greg, for rare hard hangs on i915
  loading, that also fixes hangs on reload and spurious register write
  errors.

  drm core: one fix for uninit memory

  nouveau: displayport rework caused a few regressions, Ben has been
     fixing them as the appear, along with some other fixes

  radeon: pageflipping regression fix, deep color fix, mode validation
     fixes

  i915: fbc disable, vga console kick off, backlight fix, divide-by-zero
     fix"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
  drm: fix uninitialized acquire_ctx fields (v2)
  drm/radeon: Fix radeon_irq_kms_pflip_irq_get/put() imbalance
  Revert "drm/radeon: remove drm_vblank_get|put from pflip handling"
  drm/radeon: improve dvi_mode_valid
  drm/radeon: update mode_valid testing for DP
  drm/radeon: Use dce5/6 hdmi deep color clock setup also on dce8+
  drm/nouveau/disp: fix oops in destructor with headless cards
  drm/gf117/i2c: no aux channels on this chipset
  drm/nouveau/doc: update the thermal documentation
  drm/nouveau/pwr: fix typo in fifo wrap handling
  drm/nv50/disp: fix a potential oops in supervisor handling
  drm/nouveau/disp/dp: don't touch link config after success
  drm/nouveau/kms: reference vblank for crtc during pageflip.
  drm/gk104/fb/ram: fixups from an earlier search+replace
  drm/nv50/gr: remove an unneeded write while initialising PGRAPH
  drm/nv50/gr: fix overlap while zeroing zcull regions
  drm/gf100-/gr: report class data to host on fwmthd failure
  drm/gk104/ibus: increase various random timeouts
  drm/gk104/clk: only touch divider for mode we'll be using
  drm/radeon: Bypass hw lut's for > 8 bpc framebuffer scanout.
  ...

Pull block fixes from Jens Axboe:
 "A smaller collection of fixes for the block core that would be nice to
  have in -rc2.  This pull request contains:

   - Fixes for races in the wait/wakeup logic used in blk-mq from
     Alexander.  No issues have been observed, but it is definitely a
     bit flakey currently.  Alternatively, we may drop the cyclic
     wakeups going forward, but that needs more testing.

   - Some cleanups from Christoph.

   - Fix for an oops in null_blk if queue_mode=1 and softirq completions
     are used.  From me.

   - A fix for a regression caused by the chunk size setting.  It
     inadvertently used max_hw_sectors instead of max_sectors, which is
     incorrect, and causes hangs on btrfs multi-disk setups (where hw
     sectors apparently isn't set).  From me.

   - Removal of WQ_POWER_EFFICIENT in the kblockd creation.  This was a
     recent addition as well, but it actually breaks blk-mq which relies
     on strict scheduling.  If the workqueue power_efficient mode is
     turned on, this breaks blk-mq.  From Matias.

   - null_blk module parameter description fix from Mike"

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq: bitmap tag: fix races in bt_get() function
  blk-mq: bitmap tag: fix race on blk_mq_bitmap_tags::wake_cnt
  blk-mq: bitmap tag: fix races on shared ::wake_index fields
  block: blk_max_size_offset() should check ->max_sectors
  null_blk: fix softirq completions for queue_mode == 1
  blk-mq: merge blk_mq_drain_queue and __blk_mq_drain_queue
  blk-mq: properly drain stopped queues
  block: remove WQ_POWER_EFFICIENT from kblockd
  null_blk: fix name and description of 'queue_mode' module parameter
  block: remove elv_abort_queue and blk_abort_flushes

Pull ARM SoC fixes from Arnd Bergmann:
 "A first set of bug fixes that didn't make it for the merge window, and
  two Kconfig cleanups that still make sense at this point.

  Unfortunately, one of the two cleanups caused an unintended change in
  the original version, so we had to revert one part of it and do some
  more testing to ensure the rest is really fine.  There was also a
  last-minute rebase of the patches to remove another bad commit"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: use menuconfig for sub-arch menus
  ARM: multi_v7_defconfig: re-enable SDHCI drivers
  ARM: EXYNOS: Fix compilation warning
  ARM: exynos: move sysram info to exynos.c
  ARM: dts: Specify the NAND ECC scheme explicitly on Armada 385 DB board
  ARM: dts: Specify the NAND ECC scheme explicitly on Armada 375 DB board
  ARM: exynos: cleanup kconfig option display
  misc: vexpress: fix error handling vexpress_syscfg_regmap_init()
  ARM: Remove ARCH_HAS_CPUFREQ config option
  ARM: integrator: fix section mismatch problem
  ARM: mvebu: DT: fix OpenBlocks AX3-4 RAM size
  ARM: samsung: make SAMSUNG_DMADEV optional
  remoteproc: da8xx: don't select CMA on no-MMU
  bus/arm-cci: add dependency on OF && CPU_V7
  ARM: keystone requires ARM_PATCH_PHYS_VIRT
  ARM: omap2: fix am43xx dependency on l2x0 cache

W1 reset_bus() should return zero if slave device is present.
This patch fix this issue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>