- 14 Jan, 2010 22 commits
-
-
NISHIMOTO Hiroki authored
This patch adds support for the lis3lv02d motion sensor connected via i2c on the Ecovec board. Tested with evtest. Signed-off-by:
NISHIMOTO Hiroki <nishimoto.hiroki@renesas.com> Signed-off-by:
Paul Mundt <lethal@linux-sh.org>
-
git://git390.marist.edu/pub/scm/linux-2.6Linus Torvalds authored
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: [S390] tape_char: add missing compat_ptr conversion [S390] zcrypt: add sanity check before copy_from_user() [S390] unwire sys_recvmmsg again [S390] con3215: remove empty ioctl function [S390] dasd: add proper compat pointer conversion for symmetrix ioctl [S390] mmap: add missing compat_ptr conversion to both mmap compat syscalls [S390] bug: implement arch specific __WARN macro [S390] Move __cpu_logical_map to smp.c [S390] tape_block: remove ioctl function [S390] smp: remove volatile type quilifier from __cpu_logical_map [S390] smp: setup smp_processor_id early [S390] use helpers for rlimits [S390] fs3270: add missing compat ptr conversion [S390] vmcp: add missing compat ptr conversion [S390] cio: add missing compat ptr conversion [S390] dasd: add missing compat ptr conversion [S390] remove superfluous TIF_USEDFPU bit [S390] duplicate SIGTRAP on signal delivery. [S390] clear TIF_SINGLE_STEP for new process. [S390] fix loading of PER control registers for utrace.
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits) net: fix build erros with CONFIG_BUG=n, CONFIG_GENERIC_BUG=n ipv6: skb_dst() can be NULL in ipv6_hop_jumbo(). tg3: Update copyright and driver version tg3: Disable 5717 serdes and B0 support tg3: Add reliable serdes detection for 5717 A0 tg3: Fix std rx prod ring handling tg3: Fix std prod ring nicaddr for 5787 and 57765 sfc: Fix conditions for MDIO self-test sfc: Fix polling for slow MCDI operations e1000e: workaround link issues on busy hub in half duplex on 82577/82578 e1000e: MDIO slow mode should always be done for 82577 ixgbe: update copyright dates ixgbe: Do not attempt to perform interrupts in netpoll when down cfg80211: fix refcount imbalance when wext is disabled mac80211: fix queue selection for data frames on monitor interfaces iwlwifi: silence buffer overflow warning iwlwifi: disable tx on beacon update notification iwlwifi: fix iwl_queue_used bug when read_ptr == write_ptr mac80211: fix endian error mac80211: add missing sanity checks for action frames ...
-
Octavian Purdila authored
Fixed build errors introduced by commit 7ad6848c (ip: fix mc_loop checks for tunnels with multicast outer addresses) Signed-off-by:
Octavian Purdila <opurdila@ixiacom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
This fixes CERT-FI FICORA #341748 Discovered by Olli Jarva and Tuomo Untinen from the CROSS project at Codenomicon Ltd. Just like in CVE-2007-4567, we can't rely upon skb_dst() being non-NULL at this point. We fixed that in commit e76b2b25 ("[IPV6]: Do no rely on skb->dst before it is assigned.") However commit 483a47d2 ("ipv6: added net argument to IP6_INC_STATS_BH") put a new version of the same bug into this function. Complicating analysis further, this bug can only trigger when network namespaces are enabled in the build. When namespaces are turned off, the dev_net() does not evaluate it's argument, so the dereference would not occur. So, for a long time, namespaces couldn't be turned on unless SYSFS was disabled. Therefore, this code has largely been disabled except by people turning it on explicitly for namespace development. With help from Eugene Teo <eugene@redhat.com> Signed-off-by:
-
Matt Carlson authored
This patch updates the copyright notice for 2010 and updates the version number to 3.106. Signed-off-by:
Matt Carlson <mcarlson@broadcom.com> Reviewed-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Matt Carlson authored
The B0 revision of the 5717 will not get enough testing by the time 2.6.33 ships. Since the kernel is already at RC3, serdes support will require too many patches to fix. For these reasons, this patch disables 5717 serdes support and will refuse to attach to all 5717 devices that are later than an A0 revision. Signed-off-by:
-
Matt Carlson authored
The serdes status bit does not work as intended for the 5717 A0. This patch implements an alternative detection scheme that will only be valid for A0 revisions. Signed-off-by:
-
Matt Carlson authored
There are some tg3 devices that require the driver to post new rx buffers in smaller increments. Commit 4361935a, "tg3: Consider rx_std_prod_idx a hw mailbox" changed how the driver tracks the rx producer ring updates, but it does not make any special considerations for the above-mentioned devices. For those devices, it is possible for the driver to hit the special case path, which updates the hardware mailbox register but skips updating the shadow software mailbox member. If the special case path represents the final mailbox update for this ISR iteration, the hardware and software mailbox values will be out of sync. Ultimately, this will cause the driver to use a stale mailbox value on the next iteration, which will appear to the hardware as a large rx buffer update. Bad things ensue. The fix is to update the software shadow mailbox member when the special case path is taken. Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Matt Carlson authored
Commit 87668d35, titled "tg3: Don't touch RCB nic addresses", tried to avoid assigning the nic address of the standard producer ring. Unfortunately, the default nic address is not correct for the 5787, the 5755M, or the 57765. This patch reenables the old behavior and opts out of the assignment only for the 5717. Signed-off-by:
Chow Loong Jin <hyperair@ubuntu.com> Tested-by:
Dmitry Torokhov <dtor@mail.ru> Signed-off-by:
-
Ben Hutchings authored
The MDIO self-test should not be run on boards without an MDIO PHY, such as SFN5122F-R3 and later revisions. It should also not try to address a specific MMD in an MDIO clause 22 PHY. Check the mode_support field to decide which mode to use, if any. Signed-off-by:
Ben Hutchings <bhutchings@solarflare.com> Signed-off-by:
-
Ben Hutchings authored
When the interface is down and we are using polled mode for MCDI operations, we busy-wait for completion for approximately 1 jiffy using udelay() and then back off to schedule(). But the completion will not wake the task, since we are using polled mode! We must use schedule_timeout_uninterruptible() instead. Signed-off-by:
-
Bruce Allan authored
This patch removes a delay in hardware after every received packet allowing more time for transmitted packets to go out in between received packets in half duplex. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Bruce Allan authored
A previous 82577 workaround that set the MDIO access speed to slow mode for every PHY register read/write when the cable is unplugged should instead set the access mode to always be slow before any PHY register access. Since the mode bit gets cleared when the PHY is reset, set the mode after every PHY reset. Signed-off-by:
-
Shannon Nelson authored
Signed-off-by:
Shannon Nelson <shannon.nelson@intel.com> Signed-off-by:
-
Alexander Duyck authored
This patch resolves issues seen when running netconsole and rebooting via reboot -f. The issue was due to the fact that we were attempting to perform interrupt actions when the q_vectors and rings had already been freed via the ixgbe_shutdown routines. Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Acked-by:
Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com> Signed-off-by:
-
git://xenbits.xensource.com/people/ianc/linux-2.6Linus Torvalds authored
* 'for-linus/bugfixes' of git://xenbits.xensource.com/people/ianc/linux-2.6: xen: fix hang on suspend.
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm: change drm set mode messages as DRM_DEBUG drm: fix crtc no modes printf + typo drm/radeon/kms: only evict to GTT if CP is ready drm/radeon/kms: Fix crash getting TV info with no BIOS. drm/radeon/kms/rv100: reject modes > 135 Mhz on DVI (v2) drm/radeon/kms/r6xx+: make irq handler less verbose drm/radeon/kms: fix up LVDS handling on macs (v2)
-
Benjamin Herrenschmidt authored
Commit ac4c2a3b broke the build of all powerpc boot wrappers. It attempts to add an include of autoconf.h but used the wrong path for it. It also adds -D__KERNEL__ to our boot wrapper, both things that we pretty much didn't do on purpose so far. We want our boot wrapper to remain independent enough of the kernel for various reasons, one of them being that you can "wrap" an existing kernel at distro install time which allows to ship one kernel image and a set of boot wrappers for different platforms, the wrappers don't have to be built out of the same kernel build tree. It's also incorrect to do what the patch does in our boot environment since we may not have a proper alignment exception handler which means we may not be able to fixup the few cases where an unaligned access will need SW emulation (depends on the core variant, could be when crossing page or segment boundaries for example). This patch fixes it by putting the old code back in and using the new "fancy" variant only when CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set, which happens not to be set on powerpc since we don't include autoconf.h. It also reverts the changes to our boot wrapper Makefile. This means that x86 should, afaik, keep the optimisations since its boot wrapper does include autoconf.h and define __KERNEL__ (though I doubt they make that much different outside of slow embedded processors). Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hidLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: wacom: Add BTN_TOOL_FINGER for pad button reporting HID: add device IDs for new model of Apple Wireless Keyboard HID: fix pad button definition in hid-wacom HID: Support 171 byte variant of Samsung USB IR receiver HID: blacklist ET&T TC5UH touchscreen controller
-
git://repo.or.cz/linux-kbuildLinus Torvalds authored
* 'for-33' of git://repo.or.cz/linux-kbuild: Makefile: do not override LC_CTYPE kbuild: really fix bzImage build with non-bash sh
-
OGAWA Hirofumi authored
If __block_prepare_write() was failed in block_write_begin(), the allocated blocks can be outside of ->i_size. But new truncate_pagecache() in vmtuncate() does nothing if new < old. It means the above usage is not working anymore. So, this patch fixes it by removing "new < old" check. It would need more cleanup/change. But, now -rc and truncate working is in progress, so, this tried to fix it minimum change. Acked-by:
Nick Piggin <npiggin@suse.de> Signed-off-by:
OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by:
-
- 13 Jan, 2010 18 commits
-
-
Linus Torvalds authored
* fasync-helper: fasync: split 'fasync_helper()' into separate add/remove functions
-
Heiko Carstens authored
Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com>
-
Heiko Carstens authored
It's not obvious that copy_from_user() is called with a sane length parameter here. Even though it currently seems to be correct better add a check to prevent stack corruption / exploits. Signed-off-by:
-
Heiko Carstens authored
sys_recvmmsg is reachable via sys_socketcall. So unwire it again since there is no point in having two entry points for it. Also put it to the ignore list so we don't get reminded anymore in order to wire it up. Signed-off-by:
-
Heiko Carstens authored
...instead of adding a compat ioctl function which would do nothing as well. Signed-off-by:
-
Heiko Carstens authored
Signed-off-by:
-
Heiko Carstens authored
Signed-off-by:
-
Heiko Carstens authored
This one will trap, generates shorter code and emits better debug data than the generic version. Signed-off-by:
-
Heiko Carstens authored
Finally move it to the place where it belongs to and make get rid of it for !CONFIG_SMP. Signed-off-by:
-
Heiko Carstens authored
This is just a complicated construct which always returns -EINVAL. Just remove it. Signed-off-by:
-
Heiko Carstens authored
Remove pointless qualifier. Signed-off-by:
-
Heiko Carstens authored
smp_processor_id() is supposed to work before setup_arch() gets called. Before that smp_processor_id() may return just an arbitrary value that is contained in the uninitialized boot lowcore. So provide the arch function which will override the weak function in init/main.c. Signed-off-by:
-
Jiri Slaby authored
Make sure compiler won't do weird things with limits. E.g. fetching them twice may return 2 different values after writable limits are implemented. I.e. either use rlimit helpers added in 3e10e716 or ACCESS_ONCE if not applicable. Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: linux390@de.ibm.com Cc: linux-s390@vger.kernel.org Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Heiko Carstens authored
Add missing compat ptr conversion including two additional whitespace changes that aren't worth a separate patch. Signed-off-by:
-
Heiko Carstens authored
Signed-off-by:
-
Heiko Carstens authored
Signed-off-by:
-
Heiko Carstens authored
Signed-off-by:
-
Martin Schwidefsky authored
The TIF_USEDFPU bit is always 0 for s390 and it is not tested anywhere. Remove the bit. At the same time remove the calls to clear_used_math() as well. The PF_USED_MATH bit is never set for s390 either. Signed-off-by:
-
