This fixes the behavior of the scaling_max_freq and scaling_min_freq
sysfs files in systems which had turbo disabled by the BIOS.

Caleb noticed that the HWP is programmed to operate in the wrong
P-state range on his system when the CPUFREQ policy min/max frequency
is set via sysfs.  This seems to be because in his system
intel_pstate_get_hwp_max() is returning the maximum turbo P-state even
though turbo was disabled by the BIOS, which causes intel_pstate to
scale kHz frequencies incorrectly e.g. setting the maximum turbo
frequency whenever the maximum guaranteed frequency is requested via
sysfs.
Tested-by: Caleb Callaway <caleb.callaway@intel.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Minor subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When intel_pstate switches the operation mode from "active" to
"passive" or the other way around, freeing its data structures
representing CPUs and allocating them again from scratch is not
necessary and wasteful.  Moreover, if these data structures are
preserved, the cached HWP Request MSR value from there may be
written to the MSR to start with to reinitialize it and help to
restore the EPP value set previously (it is set to 0xFF when CPUs
go offline to allow their SMT siblings to use the full range of
EPP values and that also happens when the driver gets unregistered).

Accordingly, modify the driver to only do a full cleanup on driver
object registration errors and when its status is changed to "off"
via sysfs and to write the cached HWP Request MSR value back to
the MSR on CPU init if the data structure representing the given
CPU is still there.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>

Add ->offline and ->online driver callbacks to prepare for taking a
CPU offline and to restore its working configuration when it goes
back online, respectively, to avoid invoking the ->init callback on
every CPU online which is quite a bit of unnecessary overhead.

Define ->offline and ->online so that they can be used in the
passive mode as well as in the active mode and because ->offline
will do the majority of ->stop_cpu work, the passive mode does
not need that callback any more, so drop it from there.

Also modify the active mode ->suspend and ->resume callbacks to
prevent them from interfering with the new ->offline and ->online
ones in case the latter are invoked withing the system-wide suspend
and resume code flow and make the passive mode use them too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>

Modify the EPP sysfs interface to reject attempts to change the EPP
to values different from 0 ("performance") in the active mode with
the "performance" policy (ie. scaling_governor set to "performance"),
to avoid situations in which the kernel appears to discard data
passed to it via the EPP sysfs attribute.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>

Make intel_pstate update the cached EPP value when setting the EPP
via sysfs in the active mode just like it is the case in the passive
mode, for consistency, but also for the benefit of subsequent
changes.

No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>

After commit f6ebbcf0 ("cpufreq: intel_pstate: Implement passive
mode with HWP enabled") it is possible to change the driver status
to "off" via sysfs with HWP enabled, which effectively causes the
driver to unregister itself, but HWP remains active and it forces the
minimum performance, so even if another cpufreq driver is loaded,
it will not be able to control the CPU frequency.

For this reason, make the driver refuse to change the status to
"off" with HWP enabled.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>

Pull crypto fixes from Herbert Xu:

 - fix regression in af_alg that affects iwd

 - restore polling delay in qat

 - fix double free in ingenic on error path

 - fix potential build failure in sa2ul due to missing Kconfig dependency

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: af_alg - Work around empty control messages without MSG_MORE
  crypto: sa2ul - add Kconfig selects to fix build error
  crypto: ingenic - Drop kfree for memory allocated with devm_kzalloc
  crypto: qat - add delay before polling mailbox

Pull x86 fixes from Thomas Gleixner:
 "Three interrupt related fixes for X86:

   - Move disabling of the local APIC after invoking fixup_irqs() to
     ensure that interrupts which are incoming are noted in the IRR and
     not ignored.

   - Unbreak affinity setting.

     The rework of the entry code reused the regular exception entry
     code for device interrupts. The vector number is pushed into the
     errorcode slot on the stack which is then lifted into an argument
     and set to -1 because that's regs->orig_ax which is used in quite
     some places to check whether the entry came from a syscall.

     But it was overlooked that orig_ax is used in the affinity cleanup
     code to validate whether the interrupt has arrived on the new
     target. It turned out that this vector check is pointless because
     interrupts are never moved from one vector to another on the same
     CPU. That check is a historical leftover from the time where x86
     supported multi-CPU affinities, but not longer needed with the now
     strict single CPU affinity. Famous last words ...

   - Add a missing check for an empty cpumask into the matrix allocator.

     The affinity change added a warning to catch the case where an
     interrupt is moved on the same CPU to a different vector. This
     triggers because a condition with an empty cpumask returns an
     assignment from the allocator as the allocator uses for_each_cpu()
     without checking the cpumask for being empty. The historical
     inconsistent for_each_cpu() behaviour of ignoring the cpumask and
     unconditionally claiming that CPU0 is in the mask struck again.
     Sigh.

  plus a new entry into the MAINTAINER file for the HPE/UV platform"

* tag 'x86-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/matrix: Deal with the sillyness of for_each_cpu() on UP
  x86/irq: Unbreak interrupt affinity setting
  x86/hotplug: Silence APIC only after all interrupts are migrated
  MAINTAINERS: Add entry for HPE Superdome Flex (UV) maintainers

Pull irq fixes from Thomas Gleixner:
 "A set of fixes for interrupt chip drivers:

   - Revert the platform driver conversion of interrupt chip drivers as
     it turned out to create more problems than it solves.

   - Fix a trivial typo in the new module helpers which made probing
     reliably fail.

   - Small fixes in the STM32 and MIPS Ingenic drivers

   - The TI firmware rework which had badly managed dependencies and had
     to wait post rc1"

* tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/ingenic: Leave parent IRQ unmasked on suspend
  irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by mistake
  irqchip: Revert modular support for drivers using IRQCHIP_PLATFORM_DRIVER helperse
  irqchip: Fix probing deferal when using IRQCHIP_PLATFORM_DRIVER helpers
  arm64: dts: k3-am65: Update the RM resource types
  arm64: dts: k3-am65: ti-sci-inta/intr: Update to latest bindings
  arm64: dts: k3-j721e: ti-sci-inta/intr: Update to latest bindings
  irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC
  irqchip/ti-sci-inta: Do not store TISCI device id in platform device id field
  dt-bindings: irqchip: Convert ti, sci-inta bindings to yaml
  dt-bindings: irqchip: ti, sci-inta: Update docs to support different parent.
  irqchip/ti-sci-intr: Add support for INTR being a parent to INTR
  dt-bindings: irqchip: Convert ti, sci-intr bindings to yaml
  dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent
  firmware: ti_sci: Add support for getting resource with subtype
  firmware: ti_sci: Drop unused structure ti_sci_rm_type_map
  firmware: ti_sci: Drop the device id to resource type translation

Pull scheduler fix from Thomas Gleixner:
 "A single fix for the scheduler:

   - Make is_idle_task() __always_inline to prevent the compiler from
     putting it out of line into the wrong section because it's used
     inside noinstr sections"

* tag 'sched-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Use __always_inline on is_idle_task()

Pull locking fixes from Thomas Gleixner:
 "A set of fixes for lockdep, tracing and RCU:

   - Prevent recursion by using raw_cpu_* operations

   - Fixup the interrupt state in the cpu idle code to be consistent

   - Push rcu_idle_enter/exit() invocations deeper into the idle path so
     that the lock operations are inside the RCU watching sections

   - Move trace_cpu_idle() into generic code so it's called before RCU
     goes idle.

   - Handle raw_local_irq* vs. local_irq* operations correctly

   - Move the tracepoints out from under the lockdep recursion handling
     which turned out to be fragile and inconsistent"

* tag 'locking-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  lockdep,trace: Expose tracepoints
  lockdep: Only trace IRQ edges
  mips: Implement arch_irqs_disabled()
  arm64: Implement arch_irqs_disabled()
  nds32: Implement arch_irqs_disabled()
  locking/lockdep: Cleanup
  x86/entry: Remove unused THUNKs
  cpuidle: Move trace_cpu_idle() into generic code
  cpuidle: Make CPUIDLE_FLAG_TLB_FLUSHED generic
  sched,idle,rcu: Push rcu_idle deeper into the idle path
  cpuidle: Fixup IRQ state
  lockdep: Use raw_cpu_*() for per-cpu variables

Pull cfis fix from Steve French:
 "DFS fix for referral problem when using SMB1"

* tag '5.9-rc2-smb-fix' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix check of tcon dfs in smb1

Pull powerpc fixes from Michael Ellerman:

 - Revert our removal of PROT_SAO, at least one user expressed an
   interest in using it on Power9. Instead don't allow it to be used in
   guests unless enabled explicitly at compile time.

 - A fix for a crash introduced by a recent change to FP handling.

 - Revert a change to our idle code that left Power10 with no idle
   support.

 - One minor fix for the new scv system call path to set PPR.

 - Fix a crash in our "generic" PMU if branch stack events were enabled.

 - A fix for the IMC PMU, to correctly identify host kernel samples.

 - The ADB_PMU powermac code was found to be incompatible with
   VMAP_STACK, so make them incompatible in Kconfig until the code can
   be fixed.

 - A build fix in drivers/video/fbdev/controlfb.c, and a documentation
   fix.

Thanks to Alexey Kardashevskiy, Athira Rajeev, Christophe Leroy,
Giuseppe Sacco, Madhavan Srinivasan, Milton Miller, Nicholas Piggin,
Pratik Rajesh Sampat, Randy Dunlap, Shawn Anastasio, Vaidyanathan
Srinivasan.

* tag 'powerpc-5.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/32s: Disable VMAP stack which CONFIG_ADB_PMU
  Revert "powerpc/powernv/idle: Replace CPU feature check with PVR check"
  powerpc/perf: Fix reading of MSR[HV/PR] bits in trace-imc
  powerpc/perf: Fix crashes with generic_compat_pmu & BHRB
  powerpc/64s: Fix crash in load_fp_state() due to fpexc_mode
  powerpc/64s: scv entry should set PPR
  Documentation/powerpc: fix malformed table in syscall64-abi
  video: fbdev: controlfb: Fix build for COMPILE_TEST=y && PPC_PMAC=n
  selftests/powerpc: Update PROT_SAO test to skip ISA 3.1
  powerpc/64s: Disallow PROT_SAO in LPARs by default
  Revert "powerpc/64s: Remove PROT_SAO support"

Pull USB fixes from Greg KH:
 "Let's try this again...  Here are some USB fixes for 5.9-rc3.

  This differs from the previous pull request for this release in that
  the usb gadget patch now does not break some systems, and actually
  does what it was intended to do. Many thanks to Marek Szyprowski for
  quickly noticing and testing the patch from Andy Shevchenko to resolve
  this issue.

  Additionally, some more new USB quirks have been added to get some new
  devices to work properly based on user reports.

  Other than that, the patches are all here, and they contain:

   - usb gadget driver fixes

   - xhci driver fixes

   - typec fixes

   - new quirks and ids

   - fixes for USB patches that went into 5.9-rc1.

  All of these have been tested in linux-next with no reported issues"

* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  usb: storage: Add unusual_uas entry for Sony PSZ drives
  USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
  usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
  USB: gadget: u_f: Unbreak offset calculation in VLAs
  USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
  usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
  USB: PHY: JZ4770: Fix static checker warning.
  USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
  USB: gadget: u_f: add overflow checks to VLA macros
  xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
  xhci: Do warm-reset when both CAS and XDEV_RESUME are set
  usb: host: xhci: fix ep context print mismatch in debugfs
  usb: uas: Add quirk for PNY Pro Elite
  tools: usb: move to tools buildsystem
  USB: Fix device driver race
  USB: Also match device drivers using the ->match vfunc
  usb: host: xhci-tegra: fix tegra_xusb_get_phy()
  usb: host: xhci-tegra: otg usb2/usb3 port init
  usb: hcd: Fix use after free in usb_hcd_pci_remove()
  usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
  ...

Pull EDAC fix from Borislav Petkov:
 "A fix to properly clear ghes_edac driver state on driver remove so
  that a subsequent load can probe the system properly (Shiju Jose)"

* tag 'edac_urgent_for_v5.9_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  EDAC/ghes: Fix NULL pointer dereference in ghes_edac_register()

Pull dma-mapping fix from Christoph Hellwig:
 "Fix a possibly uninitialized variable (Dan Carpenter)"

* tag 'dma-mapping-5.9-2' of git://git.infradead.org/users/hch/dma-mapping:
  dma-pool: Fix an uninitialized variable bug in atomic_pool_expand()

Most of the CPU mask operations behave the same way, but for_each_cpu() and
it's variants ignore the cpumask argument and claim that CPU0 is always in
the mask. This is historical, inconsistent and annoying behaviour.

The matrix allocator uses for_each_cpu() and can be called on UP with an
empty cpumask. The calling code does not expect that this succeeds but
until commit e027ffff ("x86/irq: Unbreak interrupt affinity setting")
this went unnoticed. That commit added a WARN_ON() to catch cases which
move an interrupt from one vector to another on the same CPU. The warning
triggers on UP.

Add a check for the cpumask being empty to prevent this.

Fixes: 2f75d9e1 ("genirq: Implement bitmap matrix allocator")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org

Merge tag 'fallthrough-fixes-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux

Pull fallthrough fixes from Gustavo A. R. Silva:
 "Fix some minor issues introduced by the recent treewide fallthrough
  conversions:

   - Fix identation issue

   - Fix erroneous fallthrough annotation

   - Remove unnecessary fallthrough annotation

   - Fix code comment changed by fallthrough conversion"

* tag 'fallthrough-fixes-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
  arm64/cpuinfo: Remove unnecessary fallthrough annotation
  media: dib0700: Fix identation issue in dib8096_set_param_override()
  afs: Remove erroneous fallthough annotation
  iio: dpot-dac: fix code comment in dpot_dac_read_raw()

Commit ef91bb19 ("kernel.h: Silence sparse warning in
lower_32_bits") caused new warnings to show in the fsldma driver, but
that commit was not to blame: it only exposed some very incorrect code
that tried to take the low 32 bits of an address.

That made no sense for multiple reasons, the most notable one being that
that code was intentionally limited to only 32-bit ppc builds, so "only
low 32 bits of an address" was completely nonsensical.  There were no
high bits to mask off to begin with.

But even more importantly fropm a correctness standpoint, turning the
address into an integer then caused the subsequent address arithmetic to
be completely wrong too, and the "+1" actually incremented the address
by one, rather than by four.

Which again was incorrect, since the code was reading two 32-bit values
and trying to make a 64-bit end result of it all.  Surprisingly, the
iowrite64() did not suffer from the same odd and incorrect model.

This code has never worked, but it's questionable whether anybody cared:
of the two users that actually read the 64-bit value (by way of some C
preprocessor hackery and eventually the 'get_cdar()' inline function),
one of them explicitly ignored the value, and the other one might just
happen to work despite the incorrect value being read.

This patch at least makes it not fail the build any more, and makes the
logic superficially sane.  Whether it makes any difference to the code
_working_ or not shall remain a mystery.
Compile-tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull i2c fixes from Wolfram Sang:
 "A core fix for ACPI matching and two driver bugfixes"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: iproc: Fix shifting 31 bits
  i2c: rcar: in slave mode, clear NACK earlier
  i2c: acpi: Remove dead code, i.e. i2c_acpi_match_device()
  i2c: core: Don't fail PRP0001 enumeration when no ID table exist

Pull s390 fixes from Vasily Gorbik:

 - Disable preemption trace in percpu macros since the lockdep code
   itself uses percpu variables now and it causes recursions.

 - Fix kernel space 4-level paging broken by recent vmem rework.

* tag 's390-5.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/vmem: fix vmem_add_range for 4-level paging
  s390: don't trace preemption in percpu macros

Pull xen fixes from Juergen Gross:
 "Two fixes for Xen: one needed for ongoing work to support virtio with
  Xen, and one for a corner case in IRQ handling with Xen"

* tag 'for-linus-5.9-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  arm/xen: Add misuse warning to virt_to_gfn
  xen/xenbus: Fix granting of vmalloc'd memory
  XEN uses irqdesc::irq_data_common::handler_data to store a per interrupt XEN data pointer which contains XEN specific information.

Merge tag 'hwmon-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - Fix tempeerature scale in gsc-hwmon driver

 - Fix divide by 0 error in nct7904 driver

 - Drop non-existing attribute from pmbus/isl68137 driver

 - Fix status check in applesmc driver

* tag 'hwmon-for-v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (gsc-hwmon) Scale temperature to millidegrees
  hwmon: (applesmc) check status earlier.
  hwmon: (nct7904) Correct divide by 0
  hwmon: (pmbus/isl68137) remove READ_TEMPERATURE_1 telemetry for RAA228228

Pull block fixes from Jens Axboe:

 - nbd timeout fix (Hou)

 - device size fix for loop LOOP_CONFIGURE (Martijn)

 - MD pull from Song with raid5 stripe size fix (Yufen)

* tag 'block-5.9-2020-08-28' of git://git.kernel.dk/linux-block:
  md/raid5: make sure stripe_size as power of two
  loop: Set correct device size when using LOOP_CONFIGURE
  nbd: restore default timeout when setting it to zero

Pull io_uring fixes from Jens Axboe:
 "A few fixes in here, all based on reports and test cases from folks
  using it. Most of it is stable material as well:

   - Hashed work cancelation fix (Pavel)

   - poll wakeup signalfd fix

   - memlock accounting fix

   - nonblocking poll retry fix

   - ensure we never return -ERESTARTSYS for reads

   - ensure offset == -1 is consistent with preadv2() as documented

   - IOPOLL -EAGAIN handling fixes

   - remove useless task_work bounce for block based -EAGAIN retry"

* tag 'io_uring-5.9-2020-08-28' of git://git.kernel.dk/linux-block:
  io_uring: don't bounce block based -EAGAIN retry off task_work
  io_uring: fix IOPOLL -EAGAIN retries
  io_uring: clear req->result on IOPOLL re-issue
  io_uring: make offset == -1 consistent with preadv2/pwritev2
  io_uring: ensure read requests go through -ERESTART* transformation
  io_uring: don't use poll handler if file can't be nonblocking read/written
  io_uring: fix imbalanced sqo_mm accounting
  io_uring: revert consumed iov_iter bytes on error
  io-wq: fix hang after cancelling pending hashed work
  io_uring: don't recurse on tsk->sighand->siglock with signalfd

Pull device properties framework fix from Rafael Wysocki:
 "Prevent the promotion of the secondary firmware node of a device to
  the primary one from leaking a pointer (Heikki Krogerus)"

* tag 'devprop-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  device property: Fix the secondary firmware node handling in set_primary_fwnode()

Pull ACPI fixes from Rafael Wysocki:
 "These fix two recent issues in the ACPI memory mappings management
  code and tighten up error handling in the ACPI driver for AMD SoCs
  (APD).

  Specifics:

   - Avoid redundant rounding to the page size in acpi_os_map_iomem() to
     address a recently introduced issue with the EFI memory map
     permission check on ARM64 (Ard Biesheuvel).

   - Fix acpi_release_memory() to wait until the memory mappings
     released by it have been really unmapped (Rafael Wysocki).

   - Make the ACPI driver for AMD SoCs (APD) check the return value of
     acpi_dev_get_property() to avoid failures in the cases when the
     device property under inspection is missing (Furquan Shaikh)"

* tag 'acpi-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI: OSL: Prevent acpi_release_memory() from returning too early
  ACPI: ioremap: avoid redundant rounding to OS page size
  ACPI: SoC: APD: Check return value of acpi_dev_get_property()

Pull power management fixes from Rafael Wysocki:
 "These fix the recently added Tegra194 cpufreq driver and the handling
  of devices using runtime PM during system-wide suspend, improve the
  intel_pstate driver documentation and clean up the cpufreq core.

  Specifics:

   - Make the recently added Tegra194 cpufreq driver use
     read_cpuid_mpir() instead of cpu_logical_map() to avoid exporting
     logical_cpu_map (Sumit Gupta).

   - Drop the automatic system wakeup event reporting for devices with
     pending runtime-resume requests during system-wide suspend to avoid
     spurious aborts of the suspend flow (Rafael Wysocki).

   - Fix build warning in the intel_pstate driver documentation and
     improve the wording in there (Randy Dunlap).

   - Clean up two pieces of code in the cpufreq core (Viresh Kumar)"

* tag 'pm-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: Use WARN_ON_ONCE() for invalid relation
  cpufreq: No need to verify cpufreq_driver in show_scaling_cur_freq()
  PM: sleep: core: Fix the handling of pending runtime resume requests
  Documentation: fix pm/intel_pstate build warning and wording
  cpufreq: replace cpu_logical_map() with read_cpuid_mpir()

* acpi-mm:
  ACPI: OSL: Prevent acpi_release_memory() from returning too early
  ACPI: ioremap: avoid redundant rounding to OS page size

* pm-cpufreq:
  cpufreq: Use WARN_ON_ONCE() for invalid relation
  cpufreq: No need to verify cpufreq_driver in show_scaling_cur_freq()
  Documentation: fix pm/intel_pstate build warning and wording
  cpufreq: replace cpu_logical_map() with read_cpuid_mpir()

Pull arm64 fixes from Catalin Marinas:

 - Fix kernel build with the integrated LLVM assembler which doesn't see
   the -Wa,-march option.

 - Fix "make vdso_install" when COMPAT_VDSO is disabled.

 - Make KVM more robust if the AT S1E1R instruction triggers an
   exception (architecture corner cases).

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  KVM: arm64: Set HCR_EL2.PTW to prevent AT taking synchronous exception
  KVM: arm64: Survive synchronous exceptions caused by AT instructions
  KVM: arm64: Add kvm_extable for vaxorcism code
  arm64: vdso32: make vdso32 install conditional
  arm64: use a common .arch preamble for inline assembly

I keep getting sparse warnings in crypto such as:

  CHECK   drivers/crypto/ccree/cc_hash.c
   drivers/crypto/ccree/cc_hash.c:49:9: warning: cast truncates bits from constant value (47b5481dbefa4fa4 becomes befa4fa4)
   drivers/crypto/ccree/cc_hash.c:49:26: warning: cast truncates bits from constant value (db0c2e0d64f98fa7 becomes 64f98fa7)
   [.. many more ..]

This patch removes the warning by adding a mask to keep sparse
happy.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull writeback fixes from Jan Kara:
 "Fixes for writeback code occasionally skipping writeback of some
  inodes or livelocking sync(2)"

* tag 'writeback_for_v5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  writeback: Drop I_DIRTY_TIME_EXPIRE
  writeback: Fix sync livelock due to b_dirty_time processing
  writeback: Avoid skipping inode writeback
  writeback: Protect inode->i_io_list with inode->i_lock

Pull gfs2 fix from Andreas Gruenbacher:
 "Fix a memory leak on filesystem withdraw.

  We didn't detect this bug because we have slab merging on by default
  (CONFIG_SLAB_MERGE_DEFAULT). Adding 'slub_nomerge' to the kernel
  command line exposed the problem"

* tag 'gfs2-v5.9-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  gfs2: add some much needed cleanup for log flushes that fail

Pull ceph fixes from Ilya Dryomov:
 "We have an inode number handling change, prompted by s390x which is a
  64-bit architecture with a 32-bit ino_t, a patch to disallow leases to
  avoid potential data integrity issues when CephFS is re-exported via
  NFS or CIFS and a fix for the bulk of W=1 compilation warnings"

* tag 'ceph-for-5.9-rc3' of git://github.com/ceph/ceph-client:
  ceph: don't allow setlease on cephfs
  ceph: fix inode number handling on arches with 32-bit ino_t
  libceph: add __maybe_unused to DEFINE_CEPH_FEATURE

For SMB1, the DFS flag should be checked against tcon->Flags rather
than tcon->share_flags.  While at it, add an is_tcon_dfs() helper to
check for DFS capability in a more generic way.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Shyam Prasad N <nspmangalore@gmail.com>

Pull MFD fixes from Lee Jones:

 - fix double free

 - handle devicetree disabled devices gracefully

* tag 'mfd-fixes-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  mfd: mfd-core: Ensure disabled devices are ignored without error
  mfd: core: Fix double-free in mfd_remove_devices_fn()

Pull drm fixes from Dave Airlie:
 "As expected a bit of an rc3 uptick, amdgpu and msm are the main ones,
  one msm patch was from the merge window, but had dependencies and we
  dropped it until the other tree had landed. Otherwise it's a couple of
  fixes for core, and etnaviv, and single i915, exynos, omap fixes.

  I'm still tracking the Sandybridge gpu relocations issue, if we don't
  see much movement I might just queue up the reverts. I'll talk to
  Daniel next week once he's back from holidays.

  core:
   - Take modeset bkl for legacy drivers

  dp_mst:
   - Allow null crtc in dp_mst

  i915:
   - Fix command parser desc matching with masks

  amdgpu:
   - Misc display fixes
   - Backlight fixes
   - MPO fix for DCN1
   - Fixes for Sienna Cichlid
   - Fixes for Navy Flounder
   - Vega SW CTF fixes
   - SMU fix for Raven
   - Fix a possible overflow in INFO ioctl
   - Gfx10 clockgating fix

  msm:
   - opp/bw scaling patch followup
   - frequency restoring fux
   - vblank in atomic commit fix
   - dpu modesetting fixes
   - fencing fix

  etnaviv:
   - scheduler interaction fix
   - gpu init regression fix

  exynos:
   - Just drop __iommu annotation to fix sparse warning

  omap:
   - locking state fix"

* tag 'drm-fixes-2020-08-28' of git://anongit.freedesktop.org/drm/drm: (41 commits)
  drm/amd/display: Fix memleak in amdgpu_dm_mode_config_init
  drm/amdgpu: disable runtime pm for navy_flounder
  drm/amd/display: Retry AUX write when fail occurs
  drm/amdgpu: Fix buffer overflow in INFO ioctl
  drm/amd/powerplay: Fix hardmins not being sent to SMU for RV
  drm/amdgpu: use MODE1 reset for navy_flounder by default
  drm/amd/pm: correct the thermal alert temperature limit settings
  drm/amdgpu: add asd fw check before loading asd
  drm/amd/display: Keep current gain when ABM disable immediately
  drm/amd/display: Fix passive dongle mistaken as active dongle in EDID emulation
  drm/amd/display: Revert HDCP disable sequence change
  drm/amd/display: Send DISPLAY_OFF after power down on boot
  drm/amdgpu/gfx10: refine mgcg setting
  drm/amd/pm: correct Vega20 swctf limit setting
  drm/amd/pm: correct Vega12 swctf limit setting
  drm/amd/pm: correct Vega10 swctf limit setting
  drm/amd/pm: set VCN pg per instances
  drm/amd/pm: enable run_btc callback for sienna_cichlid
  drivers: gpu: amd: Initialize amdgpu_dm_backlight_caps object to 0 in amdgpu_dm_update_backlight_caps
  drm/amd/display: Reject overlay plane configurations in multi-display scenarios
  ...

AT instructions do a translation table walk and return the result, or
the fault in PAR_EL1. KVM uses these to find the IPA when the value is
not provided by the CPU in HPFAR_EL1.

If a translation table walk causes an external abort it is taken as an
exception, even if it was due to an AT instruction. (DDI0487F.a's D5.2.11
"Synchronous faults generated by address translation instructions")

While we previously made KVM resilient to exceptions taken due to AT
instructions, the device access causes mismatched attributes, and may
occur speculatively. Prevent this, by forbidding a walk through memory
described as device at stage2. Now such AT instructions will report a
stage2 fault.

Such a fault will cause KVM to restart the guest. If the AT instructions
always walk the page tables, but guest execution uses the translation cached
in the TLB, the guest can't make forward progress until the TLB entry is
evicted. This isn't a problem, as since commit 5dcd0fdb ("KVM: arm64:
Defer guest entry when an asynchronous exception is pending"), KVM will
return to the host to process IRQs allowing the rest of the system to keep
running.

Cc: stable@vger.kernel.org # <v5.3: 5dcd0fdb ("KVM: arm64: Defer guest entry when an asynchronous exception is pending")
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>