Simplify code for handling state PHY_RESUMING, no functional change
intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handling of state PHY_RUNNING seems to be more complex than it needs
to be. If not polling, then we don't have to do anything, we'll
receive an interrupt and go to state PHY_CHANGELINK once the link
goes down. If polling and link is down, we don't have to go the
extra mile over PHY_CHANGELINK and call phy_read_status() again
but can set status PHY_NOLINK directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This makes use of NTF_USE in vxlan driver consistent
with bridge driver.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The new command (NCSI_CMD_SEND_CMD) is added to allow user space application
to send NC-SI command to the network card.
Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response.

The work flow is as below.

Request:
User space application
	-> Netlink interface (msg)
	-> new Netlink handler - ncsi_send_cmd_nl()
	-> ncsi_xmit_cmd()

Response:
Response received - ncsi_rcv_rsp()
	-> internal response handler - ncsi_rsp_handler_xxx()
	-> ncsi_rsp_handler_netlink()
	-> ncsi_send_netlink_rsp ()
	-> Netlink interface (msg)
	-> user space application

Command timeout - ncsi_request_timeout()
	-> ncsi_send_netlink_timeout ()
	-> Netlink interface (msg with zero data length)
	-> user space application

Error:
Error detected
	-> ncsi_send_netlink_err ()
	-> Netlink interface (err msg)
	-> user space application
Signed-off-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When starting the state machine there may be work to be done
immediately, e.g. if the initial state is PHY_UP then the state
machine may trigger an autonegotiation. Having said that I see no need
to wait a second until the state machine is run first time.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Toshiaki Makita says:

====================
veth: XDP stats improvement

ndo_xdp_xmit in veth did not update packet counters as described in [1].
Also, current implementation only updates counters on tx side so rx side
events like XDP_DROP were not collected.
This series implements the missing accounting as well as support for
ethtool per-queue stats in veth.

Patch 1: Update drop counter in ndo_xdp_xmit.
Patch 2: Update packet and byte counters for all XDP path, and drop
         counter on XDP_DROP.
Patch 3: Support per-queue ethtool stats for XDP counters.

Note that counters are maintained on per-queue basis for XDP but not
otherwise (per-cpu and atomic as before). This is because 1) tx path in
veth is essentially lockless so we cannot update per-queue stats on tx,
and 2) rx path is net core routine (process_backlog) which cannot update
per-queue based stats when XDP is disabled. On the other hand there are
real rxqs and napi handlers for veth XDP, so update per-queue stats on
rx for XDP packets, and use them to calculate tx counters as well,
contrary to the existing non-XDP counters.

[1] https://patchwork.ozlabs.org/cover/953071/#1967449
====================
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose per-queue stats for ethtool -S.
As there are only rx queues, and rx queues are used only when XDP is
used, per-queue counters are only rx XDP ones.

Example:

$ ethtool -S veth0
NIC statistics:
     peer_ifindex: 11
     rx_queue_0_xdp_packets: 28601434
     rx_queue_0_xdp_bytes: 1716086040
     rx_queue_0_xdp_drops: 28601434
     rx_queue_1_xdp_packets: 17873050
     rx_queue_1_xdp_bytes: 1072383000
     rx_queue_1_xdp_drops: 17873050
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

On XDP path veth has napi handler so we can collect statistics on
per-queue basis for XDP.

By this change now we can collect XDP_DROP drop count as well as packets
and bytes coming through ndo_xdp_xmit. Packet counters shown by
"ip -s link", sysfs stats or /proc/net/dev is now correct for XDP.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use existing atomic drop counter. Since drop path is really an
exceptional case here, I'm thinking atomic ops would not hurt the
performance.
XDP packets and bytes are not counted in ndo_xdp_xmit, but will be
accounted on rx side by the following commit.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

INADDR_ANY is hard-coded when activating UDP bearer. So, we could not
bind to a specific IP address even with replicast mode using - given
remote ip address instead of using multicast ip address.

In this commit, we fixed it by checking and switch to use appropriate
local ip address.

before:
$netstat -plu
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address           Foreign Address
udp        0      0 **0.0.0.0:6118**            0.0.0.0:*

after:
$netstat -plu
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address           Foreign Address
udp        0      0 **10.0.0.2:6118**           0.0.0.0:*
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5e-updates-2018-10-10

IPoIB netlink support and mlx5e pre-allocated netdevice initialization

IP link was broken due to the changes in IPoIB for the rdma_netdev
support after commit cd565b4b
("IB/IPoIB: Support acceleration options callbacks").

This patchset fixes IPoIB pkey creation and removal using rtnetlink by
adding support in both IPoIB ULP layer and mlx5 layer:

From Jason and Denis:
1) Introduces changes in the RDMA netdev code in order to
   allow allocation of the netdev to be done by the rtnl netdev code.
2) Reworks IPoIB initialization to use the two step rdma_netdev
   creation.

From Feras and Saeed, mlx5e netdev layer refactoring to allow accepting
pre-allocated netdevs:
3) Adds support to initialize/cleanup netdevs that are not created
   by mlx5 driver.
4) Change mlx5e netdevice layer to accept the pre-allocated netdevice
   queue number.
5) Initialize mlx5e generic structures in one place to be used for all
   netdevs types NIC/representors/IPoIB (both mlx5 allocated and
   pre-allocted).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Maciej W. Rozycki says:

====================
FDDI: DEC FDDIcontroller 700 TURBOchannel adapter support

 This is an update to <http://patchwork.ozlabs.org/patch/342737/>.  I
believe I have addressed all the requests made in the previous review
round.

 There is still one `checkpatch.pl' warning remaining:

WARNING: quoted string split across lines
+       pr_info("%s: ROM rev. %.4s, firmware rev. %.4s, RMC rev. %.4s, "
+               "SMT ver. %u\n", fp->name, rom_rev, fw_rev, rmc_rev, smt_ver);

total: 0 errors, 1 warnings, 2458 lines checked

however I think the value of staying within 80 columns is higher than the
value of having the string on a single line.  This is because with all the
formatting specifiers there it is not directly greppable based on the
final output produced to the kernel log on one hand, e.g.:

tc2: ROM rev. 1.0, firmware rev. 1.2, RMC rev. A, SMT ver. 1

while it can be easily tracked down by grepping for an obvious substring
such as "RMC rev" on the other.

 The issue with MMIO barriers I discussed in the course of the original
review turned out mostly irrelevant to this driver, because as I have
learnt in a recent Alpha/Linux discussion starting here:
<https://marc.info/?i=alpine.LRH.2.02.1808161556450.13597%20()%20file01%20!%20intranet%20!%20prod%20!%20int%20!%20rdu2%20!%20redhat%20!%20com>
our MMIO API mandates the `readX' and `writeX' accessors to be strongly
ordered with respect to each other, even if that is not implicitly
enforced by hardware.

 Consequently I have removed all the explicit ordering barriers and
instead submitted a fix for MIPS MMIO implementation, which currently does
not guarantee strong ordering (the MIPS architecture does not define bus
ordering rules except in terms of SYNC barriers), as recorded here:
<https://patchwork.linux-mips.org/project/linux-mips/list/?series=1538>.

 Enforcing strong MMIO ordering can be costly however and is often
unnecessary, e.g. when using PIO to access network frame data in onboard
packet memory.  I have therefore retained the information that would be
lost by the removal of barriers, by defining accessor wrappers suffixed by
`_o' and `_u', for accesses that have to be ordered and can be unordered
respectively.

 If we ever have an API defined for weakly-ordered MMIO accesses, then
these wrappers can be redefined accordingly.  Right now they all expand to
the respective `_relaxed' accessors, because, again, enforcing the
ordering WRT DMA transfers can be costly and we don't need it here except
in one place, where I chose to use explicit `dma_rmb' instead.

 Similarly I have replaced the completion barriers with a read back from
the respective MMIO location (all adapter MMIO registers can be read with
no side effects incurred), which will serve its purpose on the basis of
MMIO being strongly ordered (although a read from TURBOchannel is going to
be slower than `iob', making the delay incurred unnecessarily longer).

 And last but not least, I have split off the SMT Tx network tap support
to a separate change, 2/2 in this series, so that it does not block the
driver proper and can be discussed separately.

 I think it has value in that it makes the view of the outgoing network
traffic complete, as if one actually physically tapped into the outgoing
line of the ring, between the station being examined and its downstream
neighbour.  Without this part only traffic passed from applications
through the whole protocol stack can be captured and this is only a part
of the view.

 With the `dev_queue_xmit_nit' interface now exported it's only
`ptype_all' that remains private, and to define a properly abstracted API
I propose to provide am exported `dev_nit_active' predicate that tells
whether any taps are active.  This predicate is then used accordingly.

 NB if there is a long-term maintenance concern about the `dev_nit_active'
predicate, then well, corresponding inline code currently present in
`xmit_one' has to be maintained anyway, and if the resulting changes
require `defza' to be updated accordingly, then I am going to handle it;
after some 20 years with Linux it's not that I am going to disappear
anywhere anytime.  And once I am dead, which is inevitably going to happen
sooner or later, then the driver can simply be ripped from the kernel.
Though I suspect that at that point no DECstation Linux users may survive
anymore, even though hardware, being as sturdy as it is, likely will.

 I have a patch for `tcpdump' to actually decode SMT frames, which I plan
to upstream sometime.  Here's a sample of SMT traffic captured through the
`defza' driver in a small network of 4 stations and no concentrators,
printed in the most verbose mode:

01:16:59.138381 4f 00:60:b0:58:41:e7 00:60:b0:58:41:e7 73: SMT NIF ann vid:1 tid:00000270 sid:00-00-00-60-b0-58-41-e7 len:40: UNA: 00 00 00 06 0d 1a 02 ae StationDescr: 00 01 02 00 StationState: 00 00 30 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:00.332750 4f 08:00:2b:a3:a3:29 08:00:2b:a3:a3:29 73: SMT NIF ann vid:1 tid:0000013b sid:00-00-08-00-2b-a3-a3-29 len:40: UNA: 00 00 00 06 0d 1a 82 e7 StationDescr: 00 01 02 00 StationState: 00 00 30 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:00.354479 4f 00:60:b0:58:40:75 00:60:b0:58:40:75 73: SMT NIF ann vid:1 tid:0000029c sid:00-00-00-60-b0-58-40-75 len:40: UNA: 00 00 10 00 d4 74 b6 ae StationDescr: 00 01 02 00 StationState: 00 00 31 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:00.442175 4f 00:60:b0:58:41:e7 Broadcast 73: SMT NIF req vid:1 tid:00000271 sid:00-00-00-60-b0-58-41-e7 len:40: UNA: 00 00 00 06 0d 1a 02 ae StationDescr: 00 01 02 00 StationState: 00 00 30 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:00.448657 41 08:00:2b:a3:a3:29 00:60:b0:58:41:e7 73: SMT NIF rsp vid:1 tid:00000271 sid:00-00-08-00-2b-a3-a3-29 len:40: UNA: 00 00 00 06 0d 1a 82 e7 StationDescr: 00 01 02 00 StationState: 00 00 30 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:01.015152 4f 08:00:2b:a3:a3:29 Broadcast 73: SMT NIF req vid:1 tid:0000013c sid:00-00-08-00-2b-a3-a3-29 len:40: UNA: 00 00 00 06 0d 1a 82 e7 StationDescr: 00 01 02 00 StationState: 00 00 30 00 MACFrameStatusFunctions.3: 00 00 00 01
01:17:01.111644 41 08:00:2b:2e:6d:75 08:00:2b:a3:a3:29 73: SMT NIF rsp vid:1 tid:0000013c sid:00-00-08-00-2b-2e-6d-75 len:40: UNA: 00 00 10 00 d4 c5 c5 94 StationDescr: 00 01 01 00 StationState: 00 00 11 00 MACFrameStatusFunctions.2: 00 00 00 01
01:17:04.814603 4f 08:00:2b:2e:6d:75 Broadcast 73: SMT NIF req vid:1 tid:0000013c sid:00-00-08-00-2b-2e-6d-75 len:40: UNA: 00 00 10 00 d4 c5 c5 94 StationDescr: 00 01 01 00 StationState: 00 00 11 00 MACFrameStatusFunctions.2: 00 00 00 01
01:17:04.814939 4f 08:00:2b:2e:6d:75 Broadcast 73: SMT NIF req vid:1 tid:0000013c sid:00-00-08-00-2b-2e-6d-75 len:40: UNA: 00 00 10 00 d4 c5 c5 94 StationDescr: 00 01 01 00 StationState: 00 00 11 00 MACFrameStatusFunctions.2: 00 00 00 01
01:17:04.820960 4f 08:00:2b:2e:6d:75 08:00:2b:2e:6d:75 73: SMT NIF ann vid:1 tid:0000013b sid:00-00-08-00-2b-2e-6d-75 len:40: UNA: 00 00 10 00 d4 c5 c5 94 StationDescr: 00 01 01 00 StationState: 00 00 11 00 MACFrameStatusFunctions.2: 00 00 00 01

 Questions, comments?  Otherwise, please apply.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

DEC FDDIcontroller 700 (DEFZA) uses a Tx/Rx queue pair to communicate
SMT frames with adapter's firmware.  Any SMT frame received from the RMC
via the Rx queue is queued back by the driver to the SMT Rx queue for
the firmware to process.  Similarly the firmware uses the SMT Tx queue
to supply the driver with SMT frames which are queued back to the Tx
queue for the RMC to send to the ring.

When a network tap is attached to an FDDI interface handled by `defza'
any incoming SMT frames captured are queued to our usual processing of
network data received, which in turn delivers them to any listening
taps.

However the outgoing SMT frames produced by the firmware bypass our
network protocol stack and are therefore not delivered to taps.  This in
turn means that taps are missing a part of network traffic sent by the
adapter, which may make it more difficult to track down network problems
or do general traffic analysis.

Call `dev_queue_xmit_nit' then in the SMT Tx path, having checked that
a network tap is attached, with a newly-created `dev_nit_active' helper
wrapping the usual condition used in the transmit path.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the DEC FDDIcontroller 700 (DEFZA), Digital Equipment
Corporation's first-generation FDDI network interface adapter, made for
TURBOchannel and based on a discrete version of what eventually became
Motorola's widely used CAMEL chipset.

The CAMEL chipset is present for example in the DEC FDDIcontroller
TURBOchannel, EISA and PCI adapters (DEFTA/DEFEA/DEFPA) that we support
with the `defxx' driver, however the host bus interface logic and the
firmware API are different in the DEFZA and hence a separate driver is
required.

There isn't much to say about the driver except that it works, but there
is one peculiarity to mention.  The adapter implements two Tx/Rx queue
pairs.

Of these one pair is the usual network Tx/Rx queue pair, in this case
used by the adapter to exchange frames with the ring, via the RMC (Ring
Memory Controller) chip.  The Tx queue is handled directly by the RMC
chip and resides in onboard packet memory.  The Rx queue is maintained
via DMA in host memory by adapter's firmware copying received data
stored by the RMC in onboard packet memory.

The other pair is used to communicate SMT frames with adapter's
firmware.  Any SMT frame received from the RMC via the Rx queue must be
queued back by the driver to the SMT Rx queue for the firmware to
process.  Similarly the firmware uses the SMT Tx queue to supply the
driver with SMT frames that must be queued back to the Tx queue for the
RMC to send to the ring.

This solution was chosen because the designers ran out of PCB space and
could not squeeze in more logic onto the board that would be required to
handle this SMT frame traffic without the need to involve the driver, as
with the later DEFTA/DEFEA/DEFPA adapters.

Finally the driver does some Frame Control byte decoding, so to avoid
magic numbers some macros are added to <linux/if_fddi.h>.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Configuring generic network device parameters on tun will fail in
presence of IFLA_INFO_KIND attribute in IFLA_LINKINFO nested attribute
since tun_validate() always return failure.

This can be visualized with following ip-link(8) command sequences:

  # ip link set dev tun0 group 100
  # ip link set dev tun0 group 100 type tun
  RTNETLINK answers: Invalid argument

with contrast to dummy and veth drivers:

  # ip link set dev dummy0 group 100
  # ip link set dev dummy0 type dummy

  # ip link set dev veth0 group 100
  # ip link set dev veth0 group 100 type veth

Fix by returning zero in tun_validate() when @data is NULL that is
always in case since rtnl_link_ops->maxtype is zero in tun driver.

Fixes: f019a7a5 ("tun: Implement ip link del tunXXX")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2018-10-14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.20

Third set of patches for 4.20. Most notable is finalising ath10k
wcn3990 support, all components should be implemented now.

Major changes:

ath10k

* support NET_DETECT WoWLAN feature

* wcn3990 basic functionality now working after we got QMI support

mt76

* mt76x0e improvements (should be usable now)

* more mt76x0/mt76x2 unification work

brcmsmac

* fix a problem on AP mode with clients using power save mode

iwlwifi

* support for a new scan type: fast balance
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ath.git patches for 4.20. Major changes:

ath10k

* support NET_DETECT WoWLAN feature

* wcn3990 basic functionality now working after we got QMI support

mt76 patches for 4.20

* mt76x0 fixes
* mt76x0e improvements (should be usable now)
* usb support improvements
* more mt76x0/mt76x2 unification work
* minor fix for aggregation + powersave clients

Add WCN3990 QMI client handshakes for Q6 integrated WLAN connectivity
subsystem. This layer is responsible for communicating qmi control
messages to wifi fw QMI service using QMI messaging protocol.

Qualcomm MSM Interface(QMI) is a messaging format used to communicate
between components running between remote processors with underlying
transport layer based on integrated chipset(shared memory) or
discrete chipset(PCI/USB/SDIO/UART).
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add debug mask to control debug info of ath10k qmi
messaging layer.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add WLAN related VMID's to support wlan driver to set up
the remote's permissions call via TrustZone.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add device tree binding documentation details of msa
memory region for ath10k qmi client for SDM845/APQ8098
SoC into "qcom,ath10k.txt".
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add support to create the boardname for non-bmi targets
like WCN3990, which uses qmi for bdf download. This
boardname is used to parse the board data from board-2.bin.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

WLAN qmi server running in Q6 exposes host to target
cold boot qmi handshakes. Add WLAN QMI service helpers
for ath10k wcn3990 qmi client.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.

Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().

Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

A couple of macros that deal with statistics in ath9k rely on the
declaration of the 'sc' variable, which they dereference.

However, when the statistics are disabled, the new instance in
ath_cmn_process_fft() causes a warning for an unused variable:

drivers/net/wireless/ath/ath9k/common-spectral.c: In function 'ath_cmn_process_fft':
drivers/net/wireless/ath/ath9k/common-spectral.c:474:20: error: unused variable 'sc' [-Werror=unused-variable]

It's better if those macros only operate on their arguments instead of
known variable names, and adding a cast to (void) kills off that warning.

Fixes: 03224678 ("ath9k: add counters for good and errorneous FFT/spectral frames")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We added an unnecessary condition here in commit a904417f ("ath10k:
add extended per sta tx statistics support").  "legacy_rate_idx" is a u8
so it can't be negative.  The caller doesn't pass negatives either.  I
have deleted this code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath10k_pci_diag_write_mem may allocate big size of the dma memory
based on the parameter nbytes. Take firmware diag download as
example, the biggest size is about 500K. In some systems, the
allocation is likely to fail because it can't acquire such a large
contiguous dma memory.

The fix is to allocate a small size dma memory. In the loop,
driver copies the data to the allocated dma memory and writes to
the destination until all the data is written.

Tested with QCA6174 PCI with
firmware-6.bin_WLAN.RM.4.4.1-00119-QCARMSWP-1, this also affects
QCA9377 PCI.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chomium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In the noisy environment, if there are packets in the queue and can't
send out, the suspend timing will be more than 5 seconds due to the wait,
flush the queue to optimize the suspend timing, and let the upper layer to
retry the packets after resume.

Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1, but this will also affect QCA9377 PCI.
It's not a regression with new firmware releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

There is no need to compare *ps_state_enable* with < 0 because
such variable is of type u8 (8 bits, unsigned), making it
impossible to hold a negative value.

Fix this by removing such comparison.

Addresses-Coverity-ID: 1473921 ("Unsigned compared against 0")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Currently, the error handling for the call to function
ath10k_get_legacy_rate_idx() doesn't work because
*rate_idx* is of type u8 (8 bits, unsigned), which
makes it impossible for it to hold a value less
than 0.

Fix this by changing the type of variable *rate_idx*
to s8 (8 bits, signed).

Addresses-Coverity-ID: 1473914 ("Unsigned compared against 0")
Fixes: 0189dbd7 ("ath10k: get the legacy rate index to update the txrate table")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Adding WMI service check for management tx ack rssi support; this is
done to maintain common avg ack signal in user level for both data
and management tx ack packet.

Tested on QCA4019(fw version-10.4-3.2.1-00063).
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For WoWLAN support it is expected to support wake up based on discovery of
one or more known SSIDs. This is the WIPHY_WOWLAN_NET_DETECT feature,
which shows up as an NL80211 feature flag.

This shows up in 'iw phy' as:

WoWLAN support:
* wake up on network detection, up to 16 match sets

And it can be enabled with command:

iw phy0 wowlan enable net-detect interval 5000 delay 30 freqs 2412 matches ssid foo

Firmware will do scan by the configured parameters after suspend and
wakeup if it found matched SSIDs. Tested with QCA6174 hw3.0 with
firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[kvalo@codeaurora.org: fix lots of endian bugs, whitespace, commit log and style cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Currently the wmi command for setting probe request
oui, needed for mac randomization, is sent during
the mac register. At this time, during the driver
init the wmi has already been detached. This can
cause unexpected behavior since the firmware is
already down and the wmi has been detached.

Send the wmi command for setting probe request
oui during the driver start. This will make sure
that the firmware is started and wmi is initialized
before we send this command.

Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1

Fixes: 60e1d0fbSigned-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

While using 'ath10k_mac_get_rate_hw_value()' to obtain the hw value
from the passed bitrate, there is a chance of out of bound array access
when wrong bitrate is passed. This is fixed by comparing the bitrates
within the correct size of the ath10k_rates array.

Fixes commit f279294e ("ath10k: add support for configuring management
packet rate"). Also correction made to some indents used in the above commit.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c: In function 'rtl8xxxu_tx':
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:4925:7: warning:
 variable 'usedesc40' set but not used [-Wunused-but-set-variable]

drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:4921:6: warning:
 variable 'seq_number' set but not used [-Wunused-but-set-variable]

'usedesc40' and 'seq_number' are not used any more after
commit b59415c2 ("rtl8xxxu: Split filling of TX descriptors into separate functions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Remove redundant information from Pearl platform headers.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Change pcie bus layer licensing information to SPDX format.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fix checkpatch warning: use preferred 'help' option in Kconfig.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This makes the error handling somewhat cleaner -- lbs_add_card() does no
logner throw away the errno and lets its callers propagate it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>