The Acer Aspire 5738z has a button to disable (and re-enable) the
touchpad next to the touchpad.

When this button is pressed a LED underneath indicates that the touchpad
is disabled (and an event is send to userspace and GNOME shows its
touchpad enabled / disable OSD thingie).

So far so good, but after re-enabling the touchpad it no longer works.

The laptop does not have an external ps2 port, so mux mode is not needed
and disabling mux mode fixes the touchpad no longer working after toggling
it off and back on again, so lets add this laptop model to the nomux list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200331123947.318908-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

acpi_evaluate_object() and acpi_execute_simple_method() are not part of
the group of ACPI related functions which get stubbed by
include/linux/acpi.h when ACPI support is disabled, so the
IRQ_PIN_ACCESS_ACPI_METHOD handling code must be stubbed out.

For consistency use the same #if condition as which is used to replace
goodix_add_acpi_gpio_mappings with a stub.

Fixes: c5fca485 ("Input: goodix - add support for controlling the IRQ pin through ACPI methods")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200401014529.GL75430@dtor-ws
[dtor: stubbed out the ACPI method accessors]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert the EDT-FT5x06 to DT schema using json-schema.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200207084657.31195-1-benjamin.gaignard@st.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The 'axis + 1' calculation is implicit and potentially error prone.
Moreover, few lines before the axis is set explicitly for both X and Y.

Do the same when retrieving different properties for X and Y.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200303180917.12563-1-andriy.shevchenko@linux.intel.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for it by adding compatible and supported chip data
(default settings used).
The chip data on GT9147 is similar to GT912, like
- config data register has 0x8047 address
- config data register max len is 240
- config data checksum has 8-bit
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/1583144308-3781-3-git-send-email-yannick.fertre@st.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add support for it by adding compatible.
The chip data on GT9147 is similar to GT912, like
- config data register has 0x8047 address
- config data register max len is 240
- config data checksum has 8-bit
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1583144308-3781-2-git-send-email-yannick.fertre@st.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Goodix GT917S is a touchscreen chip from Goodix that is in the GT1x
family.

Add its support by assigning the gt1x config to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200228010146.12215-4-icenowy@aosc.ioSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

For Goodix GT917S chip, the chip ID string is "917S", which contains not
only numbers now.

Use string-based chip ID in the driver to support this chip and further
chips with alphanumber ID.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200228010146.12215-3-icenowy@aosc.ioSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Goodix GT917S is a new touchscreen chip from Goodix.

Add its compatible string to the device tree binding.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200228010146.12215-2-icenowy@aosc.ioSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some devices with a goodix touchscreen have more then 1 capacitive
touch-key. This commit replaces the current support for a single
touch-key, which ignored the reported key-code. With support for
up to 7 touch-keys, based upon checking the key-code which is
post-fixed to any reported touch-data.

KEY_LEFTMETA is assigned to the first touch-key (it will still be
the default keycode for devices with a single touch-key).
KEY_F1, KEY_F2... are assigned as default keycode for the other
touch-keys.

This commit also add supports for keycode remapping, so that
systemd-udev's hwdb can be used to remap the codes to send
keycodes to match the icons on the buttons for devices with more
then 1 touch-key.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-1-dmastykin@astralinux.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The goodix panel sends spurious interrupts after a 'finger up' event,
which always cause a timeout.
We were exiting the interrupt handler by reporting touch_num == 0, but
this was still processed as valid and caused the code to use the
uninitialised point_data, creating spurious key release events.

Report an error from the interrupt handler so as to avoid processing
invalid point_data further.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-2-dmastykin@astralinux.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On some ACPI/x86 devices (where we use one of the ACPI IRQ pin access
methods) the firmware is buggy, it does not properly reset the controller
at boot, and we cannot communicate with it.

Normally on ACPI/x86 devices we do not want to reset the controller at
probe time since in some cases this causes the controller to loose its
configuration and this is loaded into it by the system's firmware.
So on these systems we leave the reset_controller_at_probe flag unset,
even though we have a access to both the IRQ and reset pins and thus
could reset it.

In the case of the buggy firmware we have to reset the controller to
actually be able to talk to it.

This commit adds a special case for this, if the goodix_i2c_test() fails,
and we have not reset the controller yet; and we do have a way to reset
the controller then retry the i2c-test after resetting the controller.

This fixes the driver failing at probe on ACPI/x86 systems with this
firmware bug.
Reported-and-tested-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200311191013.10826-2-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some devices, e.g the Trekstor Primetab S11B, lose there config over
a suspend/resume cycle (likely the controller loses power during suspend).

This commit reads back the config version on resume and if matches the
expected config version it resets the controller and resends the config
we read back and saved at probe time.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-11-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Make goodix_send_cfg() take a raw buffer as argument instead of a
struct firmware *cfg, so that it can also be used to restore the config
on resume if necessary.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-10-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Our goodix_check_cfg_* helpers do things like:

	int i, raw_cfg_len = cfg->size - 2;
	...
	if (check_sum != cfg->data[raw_cfg_len]) {

When cfg->size < 2, this will end up indexing the cfg->data array with
a negative value, which will not end well.

To fix this this commit adds a new GOODIX_CONFIG_MIN_LENGTH define and
adds a minimum size check for firmware-config files using this new define.

For consistency this commit also adds a new GOODIX_CONFIG_GT9X_LENGTH for
the length used for recent gt9xx and gt1xxx chips, instead of using
GOODIX_CONFIG_MAX_LENGTH for this, so that if other length defines get
added in the future it will be clear that the MIN and MAX defines should
contain the min and max values of all the other defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-9-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Save a copy of the config in goodix_read_config(), this is a preparation
patch for restoring the config if it was lost after a supend/resume cycle.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-8-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Move the  defines to above the struct goodix_ts_data declaration, so
that the MAX defines can be used inside the struct goodix_ts_data
declaration. No functional changes, just moving a block of code.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-7-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some Apollo Lake (x86, UEFI + ACPI) devices only list the reset GPIO
in their _CRS table and the bit-banging of the IRQ line necessary to
wake-up the controller from suspend can be done by calling 2 Goodix
custom / specific ACPI methods.

This commit adds support for controlling the IRQ line in this matter,
allowing us to properly suspend the touchscreen controller on such
devices.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-6-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On most Bay Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.

These devices contain 2 GpioIo resource in their _CRS table, on all 4 such
devices which I have access to, the order of the 2 GPIOs is reset, int.

Note that the GPIO to which the touchscreen controller irq pin is connected
is configured in direct-irq mode on these Bay Trail devices, the
pinctrl-baytrail.c driver still allows controlling the pin as a GPIO in
this case, but this is not necessarily the case on other X86 ACPI
platforms, nor do we have a guarantee that the GPIO order is the same
elsewhere, so we limit the use of a _CRS table with 2 GpioIo resources
to Bay Trail devices only.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-5-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On most Cherry Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.

These devices contain 1 GpioInt and 1 GpioIo resource in their _CRS table:

Method (_CRS, 0, NotSerialized)  // _CRS: Current Resource Settings
{
    Name (RBUF, ResourceTemplate ()
    {
        I2cSerialBusV2 (0x0014, ControllerInitiated, 0x00061A80,
            AddressingMode7Bit, "\\_SB.PCI0.I2C2",
            0x00, ResourceConsumer, , Exclusive,
            )
        GpioInt (Edge, ActiveLow, Shared, PullDefault, 0x0000,
            "\\_SB.GPO1", 0x00, ResourceConsumer, ,
            )
            {   // Pin list
                0x0013
            }
        GpioIo (Shared, PullDefault, 0x0000, 0x0000,
            IoRestrictionOutputOnly,
            "\\_SB.GPO1", 0x00, ResourceConsumer, ,
            )
            {   // Pin list
                0x0019
            }
    })
    Return (RBUF) /* \_SB_.PCI0.I2C2.TCS1._CRS.RBUF */
}

There is no fixed order for these 2. This commit adds code to check that
there is 1 of each as expected and then registers a mapping matching their
order using devm_acpi_dev_add_driver_gpios().

This gives us access to both GPIOs allowing us to properly suspend the
controller during suspend, and making it possible to reset the controller
if necessary.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-4-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Before this commit we would always reset the controller at probe when we
have access to the GPIOs which are necessary to do a reset.

Doing the reset requires access to the GPIOs, but just because we have
access to the GPIOs does not mean that we should always reset the
controller at probe. On X86 ACPI platforms the BIOS / UEFI firmware will
already have reset the controller and it will have loaded the device
specific config into the controller. Doing the reset sometimes causes the
controller to lose its configuration, so on X86 ACPI platforms this is not
a good idea.

This commit adds a new reset_controller_at_probe boolean to control the
reset at probe behavior.

This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-3-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

At least on X86 ACPI platforms it is not necessary to load the touchscreen
controller config from disk, if it needs to be loaded this has already been
done by the BIOS / UEFI firmware.

Even on other (e.g. devicetree) platforms the config-loading as currently
done has the issue that the loaded cfg file is based on the controller
model, but the actual cfg is device specific, so the cfg files are not
part of linux-firmware and this can only work with a device specific OS
image which includes the cfg file.

And we do not need access to the GPIOs at all to load the config, if we
do not have access we can still load the config.

So all in all tying the decision to try to load the config from disk to
being able to access the GPIOs is not desirable. This commit adds a new
load_cfg_from_disk boolean to control the firmware loading instead.

This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-2-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.

So far we have only effectively supported this on devices which use
devicetree. On X86 ACPI platforms both looking up the pins; and using a
pin as both IRQ and GPIO is a bit more complicated. E.g. on some devices
we cannot directly access the IRQ pin as GPIO and we need to call ACPI
methods to control it instead.

This commit adds a new irq_pin_access_method field to the goodix_chip_data
struct and adds goodix_irq_direction_output and goodix_irq_direction_input
helpers which together abstract the GPIO accesses to the IRQ pin.

This is a preparation patch for adding support for properly suspending the
touchscreen on X86 ACPI platforms.

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-1-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch supports reporting resolution for ABS_MT_TOUCH_MAJOR event.
This information is needed in showing pressure/width radius.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/1582766000-23023-1-git-send-email-johnny.chuang.emc@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The touchscreen on the Cube I15-TC don't match the default display,
with 0,0 touches being reported when touching at the top-right of
the screen.

Add a quirk to invert the x coordinate.
Reported-and-tested-by: Arkadiy <arkan49@yandex.ru>
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When the distance thresholds are set the controller must be in reduced
reporting mode for them to have any effect on the interrupt generation.
This has a potentially large impact on the number of events the host
needs to process.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20200120111628.18376-1-l.stach@pengutronix.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Convert the Goodix binding to DT schema format using json-schema
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200108091118.5130-3-benjamin.gaignard@st.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add touchscreen schema for common properties
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200108091118.5130-2-benjamin.gaignard@st.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds a platform driver for supporting keyboard and mouse
interface of SGI IOC3 chips.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Link: https://lore.kernel.org/r/20200122135220.22354-1-tbogendoerfer@suse.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

There are many devices, including several mobile battery-powered
devices, using other AXP variants as their PMIC. Allow them to use
the power key as a wakeup source.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200115051253.32603-3-samuel@sholland.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Unlike most other power button drivers, this driver unconditionally
enables its wakeup IRQ. It should be using device_may_wakeup() to
respect the userspace configuration of wakeup sources.

Because the AXP20x MFD device uses regmap-irq, the AXP20x PEK IRQs are
nested off of regmap-irq's threaded interrupt handler. The device core
ignores such interrupts, so to actually disable wakeup, we must
explicitly disable all non-wakeup interrupts during suspend.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115051253.32603-2-samuel@sholland.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.

The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).

[1] commit bebcfd27 ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191210141103.15910-1-alexandru.ardelean@analog.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sync up with mainline to get SPI "delay" API changes.

We do not have to handle the wake-irq within the driver because the pm
core can handle this for us. The only use case for the suspend/resume
callbacks was to handle the wake-irq so we can remove the callbacks.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Since day one the touch controller acts as wakeup-source. This seems to
be wrong since the device supports deep-sleep mechanism [1] which
requires a reset to leave it. Also some designs won't use the
touchscreen as wakeup-source.

According discussion [2] we decided to break backward compatibility and
go the common way by using the 'wakeup-source' device-property.

[1] https://www.newhavendisplay.com/appnotes/datasheets/touchpanel/FT5x26.pdf
[2] https://patchwork.kernel.org/patch/11149037/Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The current driver behaviour was to enable the wakeup-source everytime.
After discussion [1] we decided to change that behaviour so the device
will act as wakeup-source only if the "wakeup-source" dt-property is
present.

The patch adds the binding documentation to enable the wakeup-source
capability.

[1] https://patchwork.kernel.org/patch/11149037/Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

It seems that the include order is historical increased and no one takes
care of it. Fix this to align it with the common rule to be in a
alphabetical order.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The EP0700MLP1 returns bogus data on the first register read access
(reading the threshold parameter from register 0x00):

    edt_ft5x06 2-0038: crc error: 0xfc expected, got 0x40

It ignores writes until then. This patch adds a dummy read after which
the number of sensors and parameter read/writes work correctly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Pull RISC-V fixes from Paul Walmsley:
 "Several fixes for RISC-V:

   - Fix function graph trace support

   - Prefix the CSR IRQ_* macro names with "RV_", to avoid collisions
     with macros elsewhere in the Linux kernel tree named "IRQ_TIMER"

   - Use __pa_symbol() when computing the physical address of a kernel
     symbol, rather than __pa()

   - Mark the RISC-V port as supporting GCOV

  One DT addition:

   - Describe the L2 cache controller in the FU540 DT file

  One documentation update:

   - Add patch acceptance guideline documentation"

* tag 'riscv/for-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  Documentation: riscv: add patch acceptance guidelines
  riscv: prefix IRQ_ macro names with an RV_ namespace
  clocksource: riscv: add notrace to riscv_sched_clock
  riscv: ftrace: correct the condition logic in function graph tracer
  riscv: dts: Add DT support for SiFive L2 cache controller
  riscv: gcov: enable gcov for RISC-V
  riscv: mm: use __pa_symbol for kernel symbols