After close looking, commit 8126dec3 will break:

 1. some cpu feature  in early stage too, like cpu_has_x2apic
 2. will break built-in-command line
 3. will break other memmap= and mem=
 4. early_dbgp and early_console that will use early_ioremap to access mmio (?)

So revert it.

Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>,
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Cc: Andrew Morton <akpm@linux-foundation.org>,
LKML-Reference: <4AB51DFD.2000904@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Fix following compile warning:

  arch/x86/kernel/cpu/mcheck/mce_amd.c: In function 'threshold_create_bank':
  arch/x86/kernel/cpu/mcheck/mce_amd.c:492: warning: unused variable 'c'

which shows up when kernel is compiled with CONFIG_SMP=n.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20090915151727.GB21670@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

On Intel platforms, we can use logical flat mode if there are <= 8
logical cpu's (irrespective of physical apic id values). This will
enable simplified and efficient IPI and device interrupt routing on
such platforms.

Fix the relevant comments while we are at it.

We can clean up default_setup_apic_routing() by using apic->probe()
but that is a different item.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "yinghai@kernel.org" <yinghai@kernel.org>
LKML-Reference: <1253327399.3948.747.camel@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

UV depends on the MMRHI space being identity mapped. The patch:

	x86: Make 64-bit efi_ioremap use ioremap on MMIO regions

changed this to make efi regions at a different address using
ioremap. Add the identity mapping to uv_system_init.

( Note this code was previously present but was deleted when BIOS
  added the ranges to the EFI map - previous efi code identify
  mapped the ranges. )
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090909154339.GA7946@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Add volatile-semantics to the SGI UV read/write macros that are
used to access chipset memory mapped registers. No direct
references to volatile are made. Instead the readq/writeq macros
are used.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
Cc: dwalker@fifo99.com
Cc: cfriesen@nortel.com
LKML-Reference: <20090910143149.GA14273@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

The UV BIOS has changed the way interrupt remapping is being done.
This affects the id used for sending IPIs. The upper id bits no
longer need to be masked off.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: <stable@kernel.org>
LKML-Reference: <20090909154104.GA25083@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

This was done using Coccinelle's BUG_ON semantic patch.
Signed-off-by: Daniel Walker <dwalker@fifo99.com>
Cc: Julia Lawall <julia@diku.dk>
LKML-Reference: <1252777220-30796-1-git-send-email-dwalker@fifo99.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Caught by Linus.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
[ fixed up context conflict manually. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>

* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (21 commits)
  x86, mce: Fix compilation with !CONFIG_DEBUG_FS in mce-severity.c
  x86, mce: CE in last bank prevents panic by unknown MCE
  x86, mce: Fake panic support for MCE testing
  x86, mce: Move debugfs mce dir creating to mce.c
  x86, mce: Support specifying raise mode for software MCE injection
  x86, mce: Support specifying context for software mce injection
  x86, mce: fix reporting of Thermal Monitoring mechanism enabled
  x86, mce: remove never executed code
  x86, mce: add missing __cpuinit tags
  x86, mce: fix "mce" boot option handling for CONFIG_X86_NEW_MCE
  x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUs
  x86: mce: Lower maximum number of banks to architecture limit
  x86: mce: macros to compute banks MSRs
  x86: mce: Move per bank data in a single datastructure
  x86: mce: Move code in mce.c
  x86: mce: Rename CONFIG_X86_NEW_MCE to CONFIG_X86_MCE
  x86: mce: Remove old i386 machine check code
  x86: mce: Update X86_MCE description in x86/Kconfig
  x86: mce: Make CONFIG_X86_ANCIENT_MCE dependent on CONFIG_X86_MCE
  x86, mce: use atomic_inc_return() instead of add by 1
  ...

Manually fixed up trivial conflicts:
	Documentation/feature-removal-schedule.txt
	arch/x86/kernel/cpu/mcheck/mce.c

Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (37 commits)
  sched: Fix SD_POWERSAVING_BALANCE|SD_PREFER_LOCAL vs SD_WAKE_AFFINE
  sched: Stop buddies from hogging the system
  sched: Add new wakeup preemption mode: WAKEUP_RUNNING
  sched: Fix TASK_WAKING & loadaverage breakage
  sched: Disable wakeup balancing
  sched: Rename flags to wake_flags
  sched: Clean up the load_idx selection in select_task_rq_fair
  sched: Optimize cgroup vs wakeup a bit
  sched: x86: Name old_perf in a unique way
  sched: Implement a gentler fair-sleepers feature
  sched: Add SD_PREFER_LOCAL
  sched: Add a few SYNC hint knobs to play with
  sched: Fix sync wakeups again
  sched: Add WF_FORK
  sched: Rename sync arguments
  sched: Rename select_task_rq() argument
  sched: Feature to disable APERF/MPERF cpu_power
  x86: sched: Provide arch implementations using aperf/mperf
  x86: Add generic aperf/mperf code
  x86: Move APERF/MPERF into a X86_FEATURE
  ...

Fix up trivial conflict in arch/x86/include/asm/processor.h due to
nearby addition of amd_get_nb_id() declaration from the EDAC merge.

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, pat: don't use rb-tree based lookup in reserve_memtype()
  x86: Increase MIN_GAP to include randomized stack

Merge branch 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (44 commits)
  vsnprintf: remove duplicate comment of vsnprintf
  softirq: add BLOCK_IOPOLL to softirq_to_name
  oprofile: fix oprofile regression: select RING_BUFFER_ALLOW_SWAP
  tracing: switch function prints from %pf to %ps
  vsprintf: add %ps that is the same as %pS but is like %pf
  tracing: Fix minor bugs for __unregister_ftrace_function_probe
  tracing: remove notrace from __kprobes annotation
  tracing: optimize global_trace_clock cachelines
  MAINTAINERS: Update tracing tree details
  ftrace: document function and function graph implementation
  tracing: make testing syscall events a separate configuration
  tracing: remove some unused macros
  ftrace: add compile-time check on F_printk()
  tracing: fix F_printk() typos
  tracing: have TRACE_EVENT macro use __flags to not shadow parameter
  tracing: add static to generated TRACE_EVENT functions
  ring-buffer: typecast cmpxchg to fix PowerPC warning
  tracing: add filter event logic to special, mmiotrace and boot tracers
  tracing: remove trace_event_types.h
  tracing: use the new trace_entries.h to create format files
  ...

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: Add pata_atp867x driver for Artop/Acard ATP867X controllers
  pata_amd: do not filter out valid modes in nv_mode_filter
  sata_promise: update reset code
  sata_promise: disable hotplug on 1st gen chips
  libata: fix spurious WARN_ON_ONCE() on port freeze
  ahci: restore pci_intx() handling

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc: Update defconfigs.
  sparc: Kill PROM console driver.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (66 commits)
  be2net: fix some cmds to use mccq instead of mbox
  atl1e: fix 2.6.31-git4 -- ATL1E 0000:03:00.0: DMA-API: device driver frees DMA
  pkt_sched: Fix qstats.qlen updating in dump_stats
  ipv6: Log the affected address when DAD failure occurs
  wl12xx: Fix print_mac() conversion.
  af_iucv: fix race when queueing skbs on the backlog queue
  af_iucv: do not call iucv_sock_kill() twice
  af_iucv: handle non-accepted sockets after resuming from suspend
  af_iucv: fix race in __iucv_sock_wait()
  iucv: use correct output register in iucv_query_maxconn()
  iucv: fix iucv_buffer_cpumask check when calling IUCV functions
  iucv: suspend/resume error msg for left over pathes
  wl12xx: switch to %pM to print the mac address
  b44: the poll handler b44_poll must not enable IRQ unconditionally
  ipv6: Ignore route option with ROUTER_PREF_INVALID
  bonding: make ab_arp select active slaves as other modes
  cfg80211: fix SME connect
  rc80211_minstrel: fix contention window calculation
  ssb/sdio: fix printk format warnings
  p54usb: add Zcomax XG-705A usbid
  ...

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (51 commits)
  MIPS: BCM63xx: Add integrated ethernet mac support.
  MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.
  MIPS: BCM63xx: Add Broadcom 63xx CPU definitions.
  MIPS: Octeon:  Move some platform device registration to its own file.
  MIPS: Don't corrupt page tables on vmalloc fault.
  MIPS: Shrink the size of tlb handler
  MIPS: Alchemy: override loops_per_jiffy detection
  MIPS: hw_random: Add hardware RNG for Octeon SOCs.
  MIPS: Octeon:  Add hardware RNG platform device.
  MIPS: Remove useless zero initializations.
  MIPS: Alchemy: get rid of allow_au1k_wait
  MIPS: Octeon: Set kernel_uses_llsc to false on non-SMP builds.
  MIPS: Allow kernel use of LL/SC to be separate from the presence of LL/SC.
  MIPS: Get rid of CONFIG_CPU_HAS_LLSC
  MIPS: Malta: Remove pointless use use of CONFIG_CPU_HAS_LLSC
  MIPS: Rewrite clearing of ll_bit on context switch in C
  MIPS: Rewrite sysmips(MIPS_ATOMIC_SET, ...) in C with inline assembler
  MIPS: Consolidate all CONFIG_CPU_HAS_LLSC use in a single C file.
  MIPS: Clean up linker script using new linker script macros.
  MIPS: Use PAGE_SIZE in assembly instead of _PAGE_SIZE.
  ...

Merge reason:

Suresh Siddha (1):
      x86, pat: don't use rb-tree based lookup in reserve_memtype()

... requires previous x86/pat commits already pushed to Linus.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Recent enhancement of rb-tree based lookup exposed a  bug with the lookup
mechanism in the reserve_memtype() which ensures that there are no conflicting
memtype requests for the memory range.

memtype_rb_search() returns an entry which has a start address <= new start
address. And from here we traverse the linear linked list to check if there
any conflicts with the existing mappings. As the rbtree is based on the
start address of the memory range, it is quite possible that we have several
overlapped mappings whose start address is much less than new requested start
but the end is >= new requested end. This results in conflicting memtype
mappings.

Same bug exists with the old code which uses cached_entry from where
we traverse the linear linked list. But the new rb-tree code exposes this
bug fairly easily.

For now, don't use the memtype_rb_search() and always start the search from
the head of linear linked list in reserve_memtype(). Linear linked list
for most of the systems grow's to few 10's of entries(as we track memory type
of RAM pages using struct page). So we should be ok for now.

We still retain the rbtree and use it to speed up free_memtype() which
doesn't have the same bug(as we know what exactly we are searching for
in free_memtype).

Also use list_for_each_entry_from() in free_memtype() so that we start
the search from rb-tree lookup result.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
LKML-Reference: <1253136483.4119.12.camel@sbs-t61.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

This is a new pata driver for ARTOP 867X 64bit 4-channel UDMA133 ATA ctrls.
Based on the Atp867 data sheet rev 1.2, Acard, and in part on early ide codes
from Eric Uhrhane <ericu@google.com>.
Signed-off-by: John(Jung-Ik) Lee <jilee@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Gringo <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

On a Compaq Presario V3000 laptop (NVIDIA MCP51 chipset), pata_amd selects
PIO0 mode for the PATA DVD-RAM drive instead of MWDMA2 which it supports:

ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4084N, KQ09, max MWDMA2
ata4: nv_mode_filter: 0x39f&0x7001->0x1, BIOS=0x0 (0x0) ACPI=0x7001 (60:600:0x11)
ata4.00: configured for PIO0

For some reason, the BIOS-set UDMA configuration returns 0 and the ACPI _GTM
reports that UDMA2 and PIO0 are enabled. This causes nv_mode_filter to end up
allowing only PIO0 and UDMA0-2. Since the drive doesn't support UDMA we end up
using PIO0.

Since the controllers should always support PIO4, MWDMA2 and UDMA2 regardless
of what cable type is used, let's make sure we don't filter out these modes
regardless of what wacky settings the BIOS is using.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

sata_promise's reset code has deviated quite a bit from
the Promise reference driver's, and it has been observed
to fail to recover from errors in some cases.

This patch thus updates the reset code to more closely
match the reference driver:

- soft reset (pdc_reset_port):
  * wait for ATA engine to not be in packet command mode
    (2nd gen only)
  * write reset bit in PDC_CTLSTAT before the first read
    in the loop
  * for 2nd gen SATA follow up with FPDMA reset and clearing
    error status registers
- hard reset (pdc_sata_hardreset):
  * wait for ATA engine to not be in packet command mode
    (2nd gen only)
  * reset ATA engine via the PCI control register
  * Tejun's change to use non-waiting hardreset + follow-up SRST

I'm not changing the hotplug mask bits since they are taken care
of by sata_promise's ->freeze() and ->thaw() operations. And I'm
not writing the PMP port # because that's always zero (for now).

Tested here on various controllers. In particular, one disk
which used to timeout and fail to recover from certain hdparm
and smartmonctl commands now works nicely.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

1st generation Promise SATA chips are prone to generating spurious
hotplug events which can disrupt normal operation. This has been
observed on 20376 and 20378 chips. This patch thus disables hotplug
support on 1st gen chips while leaving it enabled for 2nd gen chips.

The pdc_sata_hotplug_offset() function becomes redundant so it is
removed.

Tested on 1st gen 20376 and 20378 mainboard chips and on a 2nd gen
SATA300 PCI card.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Kurt Roeckx <kurt@roeckx.be>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Commit 54c38444 makes libata abort qcs
after the port is frozen.  This is necessary to guarantee that TF
registers are accessed after the DMA engine is shutdown after an
error.  However, this triggers WARN_ON_ONCE() check in
ata_qc_complete() spuriously.  Move WARN_ON_ONCE() downwards such that
failing commands while frozen doesn't trigger it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Commit a5bfc471 dropped explicit
pci_intx() manipulation from ahci because it seemed unnecessary and
ahci doesn't seem to be the right place to be tweaking it if it were.
This was largely okay but there are exceptions.  There was one on an
embedded platform which was fixed via firmware and now bko#14124
reports it on a HP DL320.

  http://bugzilla.kernel.org/show_bug.cgi?id=14124

I still think this isn't something libata drivers should be caring
about (the only ones which are calling pci_intx() explicitly are
libata ones and one other driver) but for now reverting the change
seems to be the right thing to do.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix MSI GX620 mixer
  ASoC: remove unused #include <linux/version.h>
  ASoC: S3C lrsync function made to work with IRQs disabled.
  ALSA: hda - Fix Dell S14 pin setup
  ALSA: hda - Fix IDT92HD83* codec setup
  ASoC: Fix display of stream name in DAPM debugfs
  ALSA: hda - Add support for HP dv6
  ALSA: hda - Fix HP/line-out initialization with IDT/STAC codecs
  ALSA: hda - Set default GPIO for IDT92HD71bxx
  ALSA: hda - Set default GPIO for STAC/IDT codecs
  ASoC: Clean up error handling in MPC5200 DMA setup
  ALSA: hda - Add missing model=auto entry for ALC269

Remove the duplicate comment of bstr_printf that is the same as the
vsnprintf.

Add the 's' option to the comment for the pointer function. This is
more of an internal function so the little duplication of the comment
here is OK.
Reported-by: Zhaolei <zhaolei@cn.fujitsu.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

With BLOCK_IOPOLL_SOFTIRQ added, softirq_to_name[] and
show_softirq_name() needs to be updated.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4AB20398.8070209@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

commit 85bac32c
    ring-buffer: only enable ring_buffer_swap_cpu when needed
broke oprofile (at least on s390, but likely on all platforms).

this patch lets oprofile select RING_BUFER_ALLOW_SWAP to make
ring_buffer_swap_cpu usable for oprofile.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
LKML-Reference: <200909162156.49239.borntraeger@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Robert Richter <robert.richter@amd.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

For direct function pointers (like what mcount provides) PowerPC64
requires the use of %ps, otherwise nothing is printed.

This patch converts all prints of functions retrieved through mcount
to use the %ps format from the %pf.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

On PowerPC64 function pointers do not point directly at the functions,
but instead point to pointers to the functions. The output of %pF expects
to point to a pointer to the function, whereas %pS will show the function
itself.

mcount returns the direct pointer to the function and not the pointer to
the pointer. Thus %pS must be used to show this. The function tracer
requires printing of the functions without offsets and uses the %pf
instead.

 %pF produces run_local_timers+0x4/0x1f
 %pf produces just run_local_timers

For PowerPC64, we need to use the direct pointer, and we only have
%pS which will produce .run_local_timers+0x4/0x1f

This patch creates a %ps that matches the %pf as %pS matches %pF.

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

* fix/hda:
  ALSA: hda - Fix MSI GX620 mixer
  ALSA: hda - Fix Dell S14 pin setup
  ALSA: hda - Fix IDT92HD83* codec setup
  ALSA: hda - Add support for HP dv6
  ALSA: hda - Fix HP/line-out initialization with IDT/STAC codecs
  ALSA: hda - Set default GPIO for IDT92HD71bxx
  ALSA: hda - Set default GPIO for STAC/IDT codecs
  ALSA: hda - Add missing model=auto entry for ALC269

* fix/asoc:
  ASoC: remove unused #include <linux/version.h>
  ASoC: S3C lrsync function made to work with IRQs disabled.
  ASoC: Fix display of stream name in DAPM debugfs
  ASoC: Clean up error handling in MPC5200 DMA setup

Merge reason: Pick up kernel/softirq.c update for dependent fix.
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Todo: Nothing ever detects CPU_BCM6338 but the code tests for it anyway.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

There is a bunch of platform device registration in
arch/mips/cavium-octeon/setup.c.  We move it to its own file in
preparation for adding more platform devices.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The code after the vmalloc_fault: label in do_page_fault() modifies
user page tables, this is not correct for 64-bit kernels.

For 64-bit kernels we should go straight to the no_context handler
skipping vmalloc_fault.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

By combining swapper_pg_dir and module_pg_dir, several if conditions
can be eliminated from the tlb exception handler. The reason they
can be combined is that, the effective virtual address of vmalloc
returned is at the bottom, and of module_alloc returned is at the
top. It also fixes the bug in vmalloc(), which happens when its
return address is not covered by the first pgd.
Signed-off-by: Wu Fei <at.wufei@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

loops_per_jiffy depends on coreclk speed;  preset it instead of
letting the kernel waste precious microseconds trying to approximate it.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>