e1000: Fix suspend/resume powerup and irq allocation

From: Auke Kok <auke-jan.h.kok@intel.com>

After 7.0.33/2.6.16, e1000 suspend/resume left the user with an enabled
device showing garbled statistics and undetermined irq allocation state,
where `ifconfig eth0 down` would display `trying to free already freed irq`.

Explicitly free and allocate irq as well as powerup the PHY during resume
fixes when needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Through some experimentation with the similarly built bcm43xx I came to
the conclusion that if the hw/firmware sets a bit in the interrupt
register, an interrupt will only be raised if that bit is included in
the interrupt mask. Hence, the interrupt mask is more like an interrupt
control mask.

This patch changes the comment to reflect that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Fix EV64120 and Ocelot builds by providing a plat_timer_setup().
  [MIPS] EV64120: Fix PCI interrupt allocation.
  [MIPS] Make irq number allocator generally available for fixing EV64120.
  [MIPS] EV64120: Fix timer initialization for HZ != 100.
  [MIPS] Ocelot 3: Fix MAC address detection after platform_device conversion.
  [MIPS] Ocelot C: Fix MAC address detection after platform_device conversion.
  [MIPS] SB1: On bootup only flush cache on local CPU.
  [MIPS] Ocelot 3: Fix large number of warnings.
  [MIPS] Ocelot C: Fix mapping of ioport address range.
  [MIPS] Ocelot C: Fix warning about missmatching format string.
  [MIPS] Ocelot C: fix eth registration after conversion to platform_device
  [MIPS] Ocelot C: Fix large number of warnings.

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (4751): Fix DBV_FE_CUSTOMISE for card drivers compiled into kernel
  V4L/DVB (4784): [saa7146_i2c] short_delay mode fixed for fast machines
  V4L/DVB (4770): Fix mode switch of Compro Videomate T300
  V4L/DVB (4787): Budget-ci: Inversion setting fixed for Technotrend 1500 T
  V4L/DVB (4786): Pvrusb2: use NULL instead of 0
  V4L/DVB (4785): Budget-ci: Change DEBIADDR_IR to a safer default
  V4L/DVB (4752): DVB: Add DVB_FE_CUSTOMISE support for MT2060

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

This fixes a warning on bootup warning in smp_call_function.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 o Fix warnings
 o 768MB worth of I/O ports were insane
 o 64-bit kernels don't need special handling because ioremap does the magic
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

  CC      arch/mips/momentum/ocelot_c/setup.o
arch/mips/momentum/ocelot_c/setup.c: In function 'momenco_time_init':
arch/mips/momentum/ocelot_c/setup.c:223: warning: format '%d' expects type 'int', but argument 2 has type 'long unsigned int'

Change data type to match format string; a 32-bit type better suits our
needs.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
  [DLM] fix oops in kref_put when removing a lockspace
  [DLM] Fix kref_put oops
  [GFS2] Fix OOM error handling
  [GFS2] Fix incorrect fs sync behaviour.
  [GFS2] don't panic needlessly

* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
  AVR32: Add missing return instruction in __raw_writesb
  AVR32: Wire up sys_epoll_pwait
  AVR32: Fix thinko in generic_find_next_zero_le_bit()
  AVR32: Get rid of board_early_init

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] IRQs too early enabled.
  [S390] revert add_active_range() usage patch.

Now that the lockspace struct is freed when the last sysfs object is released
this patch prevents use of that lockspace by sysfs. We attempt to re-get the
lockspace from the lockspace list and fail the request if it has been removed.
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

This patch fixes the recounting on the lockspace kobject. Previously the lockspace was freed while userspace could have had a
reference to one of its sysfs files, causing an oops in kref_put.

Now the lockspace kfree is moved into the kobject release() function
Signed-Off-By: Patrick Caulfield <pcaulfie@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

Fix the OOM error handling in inode.c where it was possible for
a NULL pointer to be dereferenced.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

This adds a sync_fs superblock operation for GFS2 and removes
the journal flush from write_super in favour of sync_fs where it
ought to be. This is more or less identical to the way in which ext3
does this.

This bug was pointed out by Russell Cattelan <cattelan@redhat.com>

Cc: Russell Cattelan <cattelan@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

First, SLAB_PANIC is unjustified. Second, all error propagating and backing out
is in place.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

__raw_writesb ends with a conditional branch, which is obviously
wrong. It should return after the last loop terminates.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

setup_lowcore() calls ctl_set_bit() which returns withs interrupts
enabled. The setup arch code is not supposed to enable interrupts that
early. Therefore use the __ctl_set_bit() variant.
This fixes the not working lock dependency validator on non 64 bit
systems.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Commit 7676bef9 breaks DCSS support on
s390. DCSS needs initialized struct pages to work. With the usage of
add_active_range() only the struct pages for physically present pages
are initialized.
This could be fixed if the DCSS driver would initiliaze the struct pages
itself, but this doesn't work too. This is because the mem_map array
does not include holes after the last present memory area and therefore
there is nothing that could be initialized.
To fix this and to avoid some dirty hacks revert this patch for now.
Will be added later when we move to a virtual mem_map.

Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  [PATCH] Kconfig: remove redundant NETDEVICES depends
  [PATCH] ehea: 64K page support fix
  [PATCH] ehea: Removed redundant define
  [PATCH] ehea: Nullpointer dereferencation fix
  [PATCH] bcm43xx: fix unexpected LED control values in BCM4303 sprom
  [PATCH] bcm43xx: Fix low-traffic netdev watchdog TX timeouts
  [PATCH] hostap_plx: fix CIS verification
  [PATCH] ieee80211: don't flood log with errors

auth_domain_put() forgot to unlock acquired spinlock.

Cc: Olaf Kirch <okir@monad.swb.de>
Cc: Andy Adamson <andros@citi.umich.edu>
Cc: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch takes the CTL_UNNUMBERD concept from NFS and makes it available to
all new sysctl users.

At the same time the sysctl binary interface maintenance documentation is
updated to mention and to describe what is needed to successfully maintain the
sysctl binary interface.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Since it is becoming clear that there are just enough users of the binary
sysctl interface that completely removing the binary interface from the kernel
will not be an option for foreseeable future, we need to find a way to address
the sysctl maintenance issues.

The basic problem is that sysctl requires one central authority to allocate
sysctl numbers, or else conflicts and ABI breakage occur.  The proc interface
to sysctl does not have that problem, as names are not densely allocated.

By not terminating a sysctl table until I have neither a ctl_name nor a
procname, it becomes simple to add sysctl entries that don't show up in the
binary sysctl interface.  Which allows people to avoid allocating a binary
sysctl value when not needed.

I have audited the kernel code and in my reading I have not found a single
sysctl table that wasn't terminated by a completely zero filled entry.  So
this change in behavior should not affect anything.

I think this mechanism eases the pain enough that combined with a little
disciple we can solve the reoccurring sysctl ABI breakage.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Don't warn about libpthread's access to kernel.version.  When it receives
-ENOSYS it will read /proc/sys/kernel/version.

If anything else shows up print the sysctl number string.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cal Peake <cp@absolutedigital.net>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Make the delayacct lock irqsave; this avoids the possible deadlock where
an interrupt is taken while holding the delayacct lock which needs to
take the delayacct lock.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Make the failed-to-allocate-skb warning a non-debug message.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Kai Germaschewski <kai.germaschewski@gmx.de>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The MEM_SWAPOUT crashpoint in LKDTM could be broken as some compilers
inline the call to shrink_page_list() and symbol lookup for this function
name fails.  Replacing it with the function shrink_inactive_list(), which
is the only function calling shrink_page_list().
Signed-off-by: Ankita Garg <ankita@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Cpu-hotplug locking has a minor race case caused because of setting the
variable "recursive" to NULL *after* releasing the cpu_bitmask_lock in the
function unlock_cpu_hotplug,instead of doing so before releasing the
cpu_bitmask_lock.

This was the cause of most of the recent false spurious lock_cpu_unlock
warnings.

This should fix the problem reported by Martin Lorenz reported in
http://lkml.org/lkml/2006/10/29/127.

Thanks to Srinivasa DS for pointing it out.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The existing implementation of this function seems to be looking for
a one although it should be looking for a zero. This causes trouble
for the ext2 filesystem, which tends to report -ENOSPC without this
patch.

Fix this by complementing each word before scanning.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

board_early_init() is left over from some early prototyping work
where we had to initialize the SDRAM controller ourselves. This
depends on the kernel being loaded into static RAM, which just
isn't possible on any commercially available products today.

In order to run without a boot loader, we need to create a zImage
stub or have the debugger initialize the SDRAM for us (for really
low-level debugging)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Merge branch 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes