Since IQD devices complete (most of) their transmissions synchronously,
they don't offer TX completion IRQs and have no HW coalescing controls.
But we can fake the easy parts in SW, and give the user some control wrt
to how often the TX NAPI code should be triggered to process the TX
completions.

Having per-queue controls can in particular help the dedicated mcast
queue, as it likely benefits from different fine-tuning than what the
ucast queues need.

CC: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Count the number of TX doorbells we issue to the qdio layer.

Also count the number of actual frames in a TX buffer, and then
use this data along with the byte count during TX completion.
We'll make additional use of the frame count in a subsequent patch.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We're down to a single bit flag for MAC-address related status, reflect
that in the info struct.
Also set up the flag during initialization instead of clearing it during
shutdown - one more little step towards unifying the shutdown code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The logic that deals with errors from qeth_l3_get_unique_id() is quite
complex: it sets card->unique_id to 0xfffe, additionally flags it as
UNIQUE_ID_NOT_BY_CARD and later takes this flag as cue to not propagate
card->unique_id to dev->dev_id. With dev->dev_id thus holding 0,
addrconf_ifid_eui48() applies its default behaviour.

Get rid of all the special bit masks, and just return the old uid in
case of an error. For the vast majority of cases this will be 0 (and so
we still get the desired default behaviour) - with the rare exception
where qeth_l3_get_unique_id() might have been called earlier but the
initialization then failed at a later point.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the support for polling drivers was initially added, it only
considered Input Queue 0. But as QDIO interrupts are actually for the
full device and not a single queue, this doesn't really fit for
configurations where multiple Input Queues are used.

Rework the qdio code so that interrupts for a polling driver are not
split up into actions for each queue. Instead deliver the interrupt as
a single event, and let the driver decide which queue needs what action.

When re-enabling the QDIO interrupt via qdio_start_irq(), this means
that the qdio code needs to
(1) put _all_ eligible queues back into a state where they raise IRQs,
(2) and afterwards check _all_ eligible queues for new work to bridge
    the race window.

On the qeth side of things (as the only qdio polling driver), we can now
add CQ polling support to the main NAPI poll routine. It doesn't consume
NAPI budget, and to avoid hogging the CPU we yield control after
completing one full queue worth of buffers.
The subsequent qdio_start_irq() will check for any additional work, and
have us re-schedule the NAPI instance accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Whenever all completed RX buffers have been processed
(ie. rx->b_count == 0), we call down to the HW layer to scan for
additional buffers. If no further buffers are available, the code
breaks out of the while-loop.

So we never reach the 'process an RX buffer' step with rx->b_count == 0,
eliminate that check and one level of indentation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The main NAPI poll routine should eventually handle more types of work,
beyond just the RX ring.
Split off the RX poll logic into a separate function, and simplify the
nested while-loop.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since RX buffers may contain multiple packets, qeth's NAPI poll code can
exhaust its budget in the middle of an RX buffer. Thus we keep track of
our current position within the active RX buffer, so we can resume
processing here in the next NAPI poll period.

Clean up that code by tracking the index of the active buffer element,
instead of a pointer to it.
Also simplify the code that advances to the next RX buffer when the
current buffer has been fully processed.

v2: - remove QDIO_ELEMENT_NO() macro (davem)
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TCP recvmsg() calls skb_copy_datagram_iter(), which
calls an indirect function (cb pointing to simple_copy_to_iter())
for every MSS (fragment) present in the skb.

CONFIG_RETPOLINE=y forces a very expensive operation
that we can avoid thanks to indirect call wrappers.

This patch gives a 13% increase of performance on
a single flow, if the bottleneck is the thread reading
the TCP socket.

Fixes: 950fcaec ("datagram: consolidate datagram copy to iter helpers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/chelsio/cxgb4/cxgb4_filter.c: In function cxgb4_get_free_ftid:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_filter.c:547:23:
 warning: variable tab set but not used [-Wunused-but-set-variable]

commit 8d174351 ("cxgb4: rework TC filter rule insertion across regions")
involved this, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are having multiple review cycles with all vendors trying
to implement devlink-info. Let's expand the documentation with
more information about what's implemented and motivation behind
this interface in an attempt to make the implementations easier.

Describe what each info section is supposed to contain, and make
some references to other HW interfaces (PCI caps).

Document how firmware management is expected to look, to make
it clear how devlink-info and devlink-flash work in concert.

Name some future work.

v2: - improve wording
v3: - improve wording
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It looks like the VSC8584 PHY driver is rolling its own RGMII delay
configuration code, despite the fact that the logic is mostly the same.

In fact only the register layout and position for the RGMII controls has
changed. So we need to adapt and parameterize the PHY-dependent bit
fields when calling the new generic function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andre Przywara says:

====================
net: axienet: Update error handling and add 64-bit DMA support

a minor update, fixing the 32-bit build breakage, and brightening up
Dave's christmas tree. Rebased against latest net-next/master.

This series is based on net-next as of today (9970de8b), which
includes Russell's fixes [1], solving the SGMII issues I have had.

[1] https://lore.kernel.org/netdev/E1j6trA-0003GY-N1@rmk-PC.armlinux.org.uk/

Changelog v2 .. v3:
- Use two "left-shifts by 16" to fix builds with 32-bit phys_addr_t
- reorder variable declarations

Changelog v1 .. v2:
- Add Reviewed-by: tags from Radhey
- Extend kerndoc documentation
- Convert DMA error handler tasklet to work queue
- log DMA mapping errors
- mark DMA mapping error checks as unlikely (in "hot" paths)
- return NETDEV_TX_OK on TX DMA mapping error (increasing TX drop counter)
- Request eth IRQ as an optional IRQ
- Remove no longer needed MDIO IRQ register names
- Drop DT propery check for address width, assume full 64 bit

This series updates the Xilinx Axienet driver to work on our board
here. One big issue was broken SGMII support, which Russell fixed already
(in net-next).
While debugging and understanding the driver, I found several problems
in the error handling and cleanup paths, which patches 2-7 address.
Patch 8 removes a annoying error message, patch 9 paves the way for newer
revisions of the IP. The next patch adds mii-tool support, just for good
measure.

The next four patches add support for 64-bit DMA. This is an integration
option on newer IP revisions (>= v7.1), and expects MSB bits in formerly
reserved registers. Without writing to those MSB registers, the state
machine won't trigger, so it's mandatory to access them, even if they
are zero. Patches 11 and 12 prepare the code by adding accessors, to
wrap this properly and keep it working on older IP revisions.
Patch 13 enables access to the MSB registers, by trying to write a
non-zero value to them and checking if that sticks. Older IP revisions
always read those registers as zero.
Patch 14 then adjusts the DMA mask, based on the autodetected MSB
feature. It uses the full 64 bits in this case, the rest of the system
(actual physical addresses in use) should provide a natural limit if the
chip has connected fewer address lines. If not, the parent DT node can
use a dma-range property.

The Xilinx PG138 and PG021 documents (in versions 7.1 in both cases)
were used for this series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With all DMA address accesses wrapped, we can actually support 64-bit
DMA if this option was chosen at IP integration time.
If the IP has been configured for an address width greater than 32 bits,
we assume the full 64 bit DMA width is working. In practise this will be
limited by the actual system address bus width, which will ideally be the
same as the DMA IP address width.
If this is not the case, the actual width can still be configured using a
dma-ranges property in the parent of the MAC node.

This increases the DMA mask on those systems to let the kernel choose
buffers from memory at higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When newer revisions of the Axienet IP are configured for a 64-bit bus,
we *need* to write to the MSB part of the an address registers,
otherwise the IP won't recognise this as a DMA start condition.
This is even true when the actual DMA address comes from the lower 4 GB.

To autodetect this configuration, at probe time we write all 1's to such
an MSB register, and see if any bits stick. If this is configured for a
32-bit bus, those MSB registers are RES0, so reading back 0 indicates
that no MSB writes are necessary.
On the other hands reading anything other than 0 indicated the need to
write the MSB registers, so we set the respective flag.

The actual DMA mask stays at 32-bit for now. To help bisecting, a
separate patch will enable allocations from higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer revisions of the AXI DMA IP (>= v7.1) support 64-bit addresses,
both for the descriptors itself, as well as for the buffers they are
pointing to.
This is realised by adding "MSB" words for the next and phys pointer
right behind the existing address word, now named "LSB". These MSB words
live in formerly reserved areas of the descriptor.

If the hardware supports it, write both words when setting an address.
The buffer address is handled by two wrapper functions, the two
occasions where we set the next pointers are open coded.

For now this is guarded by a flag which we don't set yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer versions of the Xilink DMA IP support busses with more than 32
address bits, by introducing an MSB word for the registers holding DMA
pointers (tail/current, RX/TX descriptor addresses).
On IP configured for more than 32 bits, it is also *required* to write
both words, to let the IP recognise this as a start condition for an
MM2S request, for instance.

Wrap the DMA pointer writes with a separate function, to add this
functionality later. For now we stick to the lower 32 bits.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mii-tool is useful for debugging, and all it requires to work is to wire
up the ioctl ops function pointer.
Add this to the axienet driver to enable mii-tool.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Newer revisions of the IP don't have these registers. Since we don't
really use them, just drop them from the ethtools dump.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the DT binding, the Ethernet core interrupt is optional.

Use platform_get_irq_optional() to avoid the error message when the
IRQ is not specified.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Especially with the default 32-bit DMA mask, DMA buffers are a limited
resource, so their allocation can fail.
So as the DMA API documentation requires, add error checking code after
dma_map_single() calls to catch the case where we run out of "low" memory.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Factor out the code that cleans up a number of connected TX descriptors,
as we will need it to properly roll back a failed _xmit() call.
There are subtle differences between cleaning up a successfully sent
chain (unknown number of involved descriptors, total data size needed)
and a chain that was about to set up (number of descriptors known), so
cater for those variations with some extra parameters.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since 0 is a valid DMA address, we cannot use the physical address to
check whether a TX descriptor is valid and is holding a DMA mapping.

Use the "cntrl" member of the descriptor to make this decision, as it
contains at least the length of the buffer, so 0 points to an
uninitialised buffer.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When axienet_dma_bd_init() bails out during the initialisation process,
it might do so with parts of the structure already allocated and
initialised, while other parts have not been touched yet. Before
returning in this case, we call axienet_dma_bd_release(), which does not
take care of this corner case.
This is most obvious by the first loop happily dereferencing
lp->rx_bd_v, which we actually check to be non NULL *afterwards*.

Make sure we only unmap or free already allocated structures, by:
- directly returning with -ENOMEM if nothing has been allocated at all
- checking for lp->rx_bd_v to be non-NULL *before* using it
- only unmapping allocated DMA RX regions

This avoids NULL pointer dereferences when initialisation fails.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.

This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.

Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DMA error handler routine is currently a tasklet, scheduled to run
after the DMA error IRQ was handled.
However it needs to take the MDIO mutex, which is not allowed to do in a
tasklet. A kernel (with debug options) complains consequently:
[  614.050361] net eth0: DMA Tx error 0x174019
[  614.064002] net eth0: Current BD is at: 0x8f84aa0ce
[  614.080195] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
[  614.109484] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 40, name: kworker/u4:4
[  614.135428] 3 locks held by kworker/u4:4/40:
[  614.149075]  #0: ffff000879863328 ((wq_completion)rpciod){....}, at: process_one_work+0x1f0/0x6a8
[  614.177528]  #1: ffff80001251bdf8 ((work_completion)(&task->u.tk_work)){....}, at: process_one_work+0x1f0/0x6a8
[  614.209033]  #2: ffff0008784e0110 (sk_lock-AF_INET-RPC){....}, at: tcp_sendmsg+0x24/0x58
[  614.235429] CPU: 0 PID: 40 Comm: kworker/u4:4 Not tainted 5.6.0-rc3-00926-g4a165a9d5921 #26
[  614.260854] Hardware name: ARM Test FPGA (DT)
[  614.274734] Workqueue: rpciod rpc_async_schedule
[  614.289022] Call trace:
[  614.296871]  dump_backtrace+0x0/0x1a0
[  614.308311]  show_stack+0x14/0x20
[  614.318751]  dump_stack+0xbc/0x100
[  614.329403]  ___might_sleep+0xf0/0x140
[  614.341018]  __might_sleep+0x4c/0x80
[  614.352201]  __mutex_lock+0x5c/0x8a8
[  614.363348]  mutex_lock_nested+0x1c/0x28
[  614.375654]  axienet_dma_err_handler+0x38/0x388
[  614.389999]  tasklet_action_common.isra.15+0x160/0x1a8
[  614.405894]  tasklet_action+0x24/0x30
[  614.417297]  efi_header_end+0xe0/0x494
[  614.429020]  irq_exit+0xd0/0xd8
[  614.439047]  __handle_domain_irq+0x60/0xb0
[  614.451877]  gic_handle_irq+0xdc/0x2d0
[  614.463486]  el1_irq+0xcc/0x180
[  614.473451]  __tcp_transmit_skb+0x41c/0xb58
[  614.486513]  tcp_write_xmit+0x224/0x10a0
[  614.498792]  __tcp_push_pending_frames+0x38/0xc8
[  614.513126]  tcp_rcv_established+0x41c/0x820
[  614.526301]  tcp_v4_do_rcv+0x8c/0x218
[  614.537784]  __release_sock+0x5c/0x108
[  614.549466]  release_sock+0x34/0xa0
[  614.560318]  tcp_sendmsg+0x40/0x58
[  614.571053]  inet_sendmsg+0x40/0x68
[  614.582061]  sock_sendmsg+0x18/0x30
[  614.593074]  xs_sendpages+0x218/0x328
[  614.604506]  xs_tcp_send_request+0xa0/0x1b8
[  614.617461]  xprt_transmit+0xc8/0x4f0
[  614.628943]  call_transmit+0x8c/0xa0
[  614.640028]  __rpc_execute+0xbc/0x6f8
[  614.651380]  rpc_async_schedule+0x28/0x48
[  614.663846]  process_one_work+0x298/0x6a8
[  614.676299]  worker_thread+0x40/0x490
[  614.687687]  kthread+0x134/0x138
[  614.697804]  ret_from_fork+0x10/0x18
[  614.717319] xilinx_axienet 7fe00000.ethernet eth0: Link is Down
[  615.748343] xilinx_axienet 7fe00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off

Since tasklets are not really popular anymore anyway, lets convert this
over to a work queue, which can sleep and thus can take the MDIO mutex.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to axienet, the temac driver is now architecture agnostic, and
can be at least compiled for several architectures.
Especially the fact that this is a soft IP for implementing in FPGAs
makes the current restriction rather pointless, as it could literally
appear on any architecture, as long as an FPGA is connected to the bus.

The driver hasn't been actually tried on any hardware, it is just a
drive-by patch when doing the same for axienet (a similar patch for
axienet is already merged).

This (temac and axienet) have been compile-tested for:
alpha hppa64 microblaze mips64 powerpc powerpc64 riscv64 s390 sparc64
(using kernel.org cross compilers).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, ethtool feature mask for checksum command is ORed with
NETIF_F_FCOE_CRC_BIT, which is bit's position number, instead of the
actual feature bit - NETIF_F_FCOE_CRC.

The invalid bitmask here might affect unrelated features when toggling
TX checksumming. For example, TX checksumming is always mistakenly
reported as enabled on the netdevs tested (mlx5, virtio_net).

Fixes: f70bb065 ("ethtool: update mapping of features to legacy ioctl requests")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

use readl_poll_timeout() to replace the poll codes for simplify
iproc_mdio_wait_for_idle() function
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-2020-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.7

Second set of patches for v5.7. Lots of cleanup patches this time, but
of course various new features as well fixes.

When merging with wireless-drivers this pull request has a conflict in:

drivers/net/wireless/intel/iwlwifi/pcie/drv.c

To solve that just drop the changes from commit cf52c8a7 in
wireless-drivers and take the hunk from wireless-drivers-next as is.
The list of specific subsystem device IDs are not necessary after
commit d6f2134a (in wireless-drivers-next) anymore, the detection
is based on other characteristics of the devices.

Major changes:

qtnfmac

* support WPA3 SAE and OWE in AP mode

ath10k

* support for getting btcoex settings from Device Tree

* support QCA9377 SDIO device

ath11k

* add HE rate accounting

* add thermal sensor and cooling devices

mt76

* MT7663 support for the MT7615 driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
PTP_CLK pin configuration for SJA1105 DSA driver

This series adds support for the PTP_CLK pin on SJA1105 to be configured
via the PTP subsystem, in the "periodic output" and "external timestamp
input" modes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The SJA1105 switch family has a PTP_CLK pin which emits a signal with
fixed 50% duty cycle, but variable frequency and programmable start time.

On the second generation (P/Q/R/S) switches, this pin supports even more
functionality. The use case described by the hardware documents talks
about synchronization via oneshot pulses: given 2 sja1105 switches,
arbitrarily designated as a master and a slave, the master emits a
single pulse on PTP_CLK, while the slave is configured to timestamp this
pulse received on its PTP_CLK pin (which must obviously be configured as
input). The difference between the timestamps then exactly becomes the
slave offset to the master.

The only trouble with the above is that the hardware is very much tied
into this use case only, and not very generic beyond that:
 - When emitting a oneshot pulse, instead of being told when to emit it,
   the switch just does it "now" and tells you later what time it was,
   via the PTPSYNCTS register. [ Incidentally, this is the same register
   that the slave uses to collect the ext_ts timestamp from, too. ]
 - On the sync slave, there is no interrupt mechanism on reception of a
   new extts, and no FIFO to buffer them, because in the foreseen use
   case, software is in control of both the master and the slave pins,
   so it "knows" when there's something to collect.

These 2 problems mean that:
 - We don't support (at least yet) the quirky oneshot mode exposed by
   the hardware, just normal periodic output.
 - We abuse the hardware a little bit when we expose generic extts.
   Because there's no interrupt mechanism, we need to poll at double the
   frequency we expect to receive a pulse. Currently that means a
   non-configurable "twice a second".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The AVB table contains the CAS_MASTER field (to be added in the next
patch) which decides the direction of the PTP_CLK pin.

Reconfiguring this field dynamically is highly preferable to having to
reset the switch and upload a new static configuration, so we add
support for exactly that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because the PTP_CLK pin starts toggling only at a time higher than the
current PTP clock, this helper from the time-aware shaper code comes in
handy here as well. We'll use it to transform generic user input for the
perout request into valid input for the sja1105 hardware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These fields configure the destination and source MAC address that the
switch will put in the Ethernet frames sent towards the CPU port that
contain RX timestamps for PTP.

These fields do not enable the feature itself, that is configured via
SEND_META0 and SEND_META1 in the General Params table.

The implication of this patch is that the AVB Params table will always
be present in the static config. Which doesn't really hurt.

This is needed because in a future patch, we will add another field from
this table, CAS_MASTER, for configuring the PTP_CLK pin function. That
can be configured irrespective of whether RX timestamping is enabled or
not, so always having this table present is going to simplify things a
bit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

checkpatch found a lack of appropriate whitespace after certain keywords
as per the style guide. Add it in.
Signed-off-by: Logan Magee <mageelog@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dejin Zheng says:

====================
introduce read_poll_timeout

This patch sets is introduce read_poll_timeout macro, it is an extension
of readx_poll_timeout macro. the accessor function op just supports only
one parameter in the readx_poll_timeout macro, but this macro can
supports multiple variable parameters for it. so functions like
phy_read(struct phy_device *phydev, u32 regnum) and
phy_read_mmd(struct phy_device *phydev, int devad, u32 regnum) can
use this poll timeout framework.

the first patch introduce read_poll_timeout macro, and the second patch
redefined readx_poll_timeout macro by read_poll_timeout(), and the other
patches are examples using read_poll_timeout macro.

v6 -> v7:
	- add a parameter to supports that it can sleep some time
	  before read operation in read_poll_timeout macro.
	- add prefix with double underscores for some variable to avoid
	  any variable re-declaration or shadowing in patch 3 and patch
	  7.
v5 -> v6:
	- add some check to keep the code more similar in patch 8
v4 -> v5:
	- add some msleep() before call phy_read_mmd_poll_timeout() to
	  keep the code more similar in patch 6 and patch 9.
	- add a patch of drop by v4, it can add msleep before call
	  phy_read_poll_timeout() to keep the code more similar.
v3 -> v4:
	- add 3 examples of using new functions.
	- deal with precedence issues for parameter cond.
	- drop a patch about phy_poll_reset() function.
v2 -> v3:
	- modify the parameter order of newly added functions.
	  phy_read_mmd_poll_timeout(val, cond, sleep_us, timeout_us, \
				     phydev, devaddr, regnum)
				||
				\/
	  phy_read_mmd_poll_timeout(phydev, devaddr regnum, val, cond, \
				    sleep_us, timeout_us)

	  phy_read_poll_timeout(val, cond, sleep_us, timeout_us, \
				phydev, regnum)
				||
				\/
	  phy_read_poll_timeout(phydev, regnum, val, cond, sleep_us, \
				timeout_us)
v1 -> v2:
	- passed a phydev, device address and a reg to replace args...
	  parameter in phy_read_mmd_poll_timeout() by Andrew Lunn 's
	  suggestion in patch 3. Andrew Lunn <andrew@lunn.ch>, Thanks
	  very much for your help!
	- also in patch 3, handle phy_read_mmd return an error(the return
	  value < 0) in phy_read_mmd_poll_timeout(). Thanks Andrew
	  again.
	- in patch 6, pass a phydev and a reg to replace args...
	  parameter in phy_read_poll_timeout(), and also handle the
	  phy_read() function's return error.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use phy_read_poll_timeout() to replace the poll codes for
simplify lan87xx_read_status() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use phy_read_poll_timeout() to replace the poll codes for
simplify the code in phy_poll_reset() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>