- 16 Jun, 2009 40 commits
-
-
Devin Heitmueller authored
Defer loading of the xc5000 firmware until it is actually needed. This helps on distros that have hald, which results in the device not being available for use for around ten seconds in cases where the i2c bus is slow (such as the HVR-950Q). Also, the firmware load isn't really useful since we immediately put the device to sleep afterward, which means a firmware reload will be required anyway. Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Devin Heitmueller authored
Provide for the ability for a user to disable putting the tuner to sleep, in case he doesn't want to incur the cost of reloading the firmware when starting up his/her application. The module options are intentionally identical to xc3028. Signed-off-by:
-
Devin Heitmueller authored
Make it a little more obvious in the dmesg output what is going on during firmware upload. This is more important for boards like the HVR-950q that take nearly seven seconds to do the upload. Signed-off-by:
-
Devin Heitmueller authored
Starting in firmware version 1.1.44, Xceive recommends using the FINERFREQ for all normal tuning (the doc indicates reg 0x03 should only be used for fast scanning for channel lock) Signed-off-by:
-
Devin Heitmueller authored
Expose the firmware build number along with the other version info Signed-off-by:
-
Devin Heitmueller authored
The xc5000 datasheet indicates that the reset pin only needs to be held low for 10ms. Reduce the value accordingly, which speeds up the firmware load time a bit. Signed-off-by:
-
Devin Heitmueller authored
Xceive got rid of the XREG_POWER_DOWN register in later firmware revisions. Their technical support informed me that the correct way to put the tuner to sleep is to pull the reset pin (but don't reload the firmware). Signed-off-by:
-
Devin Heitmueller authored
This switches to a new version of the xc5000 firmware, extracted from the latest Hauppauge driver. It includes the support for the XREG_BUSY register (a lack of which was causing tuning to take 3200ms instead of around 300ms). Signed-off-by:
-
Devin Heitmueller authored
Don't sleep for 400ms polling the tuner's lock if in digital mode (since the xc5000 lock status registers appear to only be reliable in analog mode) Signed-off-by:
Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Devin Heitmueller authored
Bring back the code that puts the xc5000 to sleep. For the Pinnacle 801e this results in power consumption at idle dropping from 325ma to 124ma. If there are *actually* any devices that don't work in this configuration, they should set dvb_frontend.ops.tuner_ops.sleep to NULL (per mkrufky's suggestion) Also, had to make sure we were making sure the firmware was loaded in the digital version of set_params, or else we end up get i2c errors if the device is asleep Signed-off-by:
-
Devin Heitmueller authored
Make return value checking for calls to i2c routines explicit. Signed-off-by:
-
Devin Heitmueller authored
Cleanup the i2c write routine, getting rid of a passthrough function with only one caller Signed-off-by:
-
Devin Heitmueller authored
This patch centralizes the i2c read functions, and eliminates pass-through function only called by one caller. Make reading of xc5000 registers an atomic i2c transaction in case we're on a multi-master bus. Signed-off-by:
-
Devin Heitmueller authored
Properly handle tuner reset failures (before it was always returning success) Signed-off-by:
-
Dmitri Belimov authored
Signed-off-by:
Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
Michael Krufky <mkrufky@kernellabs.com> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Steven Toth authored
The patch means the board will be recognised, and the parts brought out of reset correctly. This patches depends on the centralized GPIO patch to be merged. What's missing before the HVR-1270 will function for DTV? The model# needs to be added to avoid 'unknown model' output and the LG3305/Tuner need to be attached in cx23885-dvb.c Signed-off-by:
Steven Toth <stoth@kernellabs.com> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Steven Toth authored
The GPIO's on the product can be in one of three places. To date we've mainly used the GPIO's on the bridge itself, and once on the encoder. Rather than having the complexity of multiple GPIO writes/reads from isolated placed in the driver we'll route them through this function, so we can make intelligent decisions about 1) Where the GPIO lives and 2) Whether it conflicts (based on board) with some other function to avoid bugs. Signed-off-by:
-
Oliver Endriss authored
Some whitespace adjustments. Signed-off-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
Oliver Endriss authored
av7110_av_start_play() should return 0 on success. Signed-off-by:
-
Oliver Endriss authored
Fixed VIDEO_SLOWMOTION ioctl. Signed-off-by:
-
Oliver Endriss authored
Discard PES packet if transport error indicator flag is set. Signed-off-by:
-
Oliver Endriss authored
Implemented TS replay capability. audio/video devices are able to process PES and TS data now. Signed-off-by:
-
Randy Dunlap authored
Build fails when CONFIG_I2C=n, so handle that case in the if block: drivers/built-in.o: In function `v4l2_device_unregister': (.text+0x157821): undefined reference to `i2c_unregister_device' Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Steven Toth authored
... else DVB-T tuning will not work. Signed-off-by:
Steven Toth <stoth@linuxtv.org> Signed-off-by:
-
Steven Toth authored
Currently, DVB-T is broken and this fixes it. The PVRUSB2 has an odd I2C bus configuration where opening the i2c gate on the digital and analog demod causes the tuner to fail. This needs to be protected against for the PVRUSB2. Signed-off-by:
-
Hans Verkuil authored
g_tuner handled capability, audmode and rxsubchans incorrectly. Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Hans Verkuil authored
Remove bogus flags field Signed-off-by:
-
Randy Dunlap authored
soc_camera uses i2c_*() functions and has build errors when CONFIG_I2C=n: ERROR: "i2c_new_device" [drivers/media/video/soc_camera.ko] undefined! ERROR: "i2c_get_adapter" [drivers/media/video/soc_camera.ko] undefined! ERROR: "i2c_put_adapter" [drivers/media/video/soc_camera.ko] undefined! ERROR: "i2c_unregister_device" [drivers/media/video/soc_camera.ko] undefined! Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Andy Walls authored
The TCL MNM05-04 is used on some HVR-1600 models. It appears to be similar to the TCL MFMN05-4 but without FM radio. The TUNER_PHILIPS_FM1236_MK3 tuner definition appears to be the proper existing tuner definition to use for this tuner. Reported-by:
Matt Beadon <matt.beadon@gmail.com> Tested-by:
Andy Walls <awalls@radix.net> Signed-off-by:
-
Andy Walls authored
Signed-off-by:
-
Mike Isely authored
Signed-off-by:
Mike Isely <isely@pobox.com> Signed-off-by:
-
Jean Delvare authored
The i2c core used to maintain a list of client for each adapter. This is a duplication of what the driver core already does, so this list will be removed as part of a future cleanup. Anyone using this list must stop doing so. For pvrusb2, I propose the following change, which should lead to an equally informative output. The only difference is that i2c clients which are not a v4l2 subdev won't show up, but I guess this case is not supposed to happen anyway. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Mike Isely authored
Kick up the pvrusb2 version number advertised through the v4l interface. This value really has almost no meaning because I don't make a serious attempt to version the driver in this manner (otherwise this one line becomes a nasty hotspot of changes and merge conflicts). The value that is here is really a historical thing. However Hans Verkuil thought it might be a good idea to bump up the number anyway right now since the driver's mechanism for communicating with the v4l core has pretty much completely changed. Sending out a Signed-off-by:
-
