- 26 Sep, 2006 40 commits
-
-
Yeasah Pell authored
1) It sets LNBDCPol differently based on the card type. Now it should work properly for both the kworld and geniatech cards. 2) It stops returning an error for the SEC_VOLTAGE_OFF voltage command (the cx88-dvb level handles the actual voltage on/off, but it still passes the ioctl down to the cx24123 level, which previously rejected the OFF as invalid so the ioctl would report failure) Acked-by:
Manu Abraham <manu@linuxtv.org> Signed-off-by:
Yeasah Pell <yeasah@schwide.net> Signed-off-by:
Mauro Carvalho Chehab <mchehab@infradead.org>
-
Oliver Endriss authored
Some DVB-T cards with Grundig 29504-401 tuner use subsystem id 13c2:0001 (reported by Stuart Butterfield). Signed-off-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
Mauro Carvalho Chehab authored
Hardware algorithm needs to be configured to: 1) Increase timeout constants, to detect weaker signals; 2) do a wider zigzag search. Acked-by:
-
Mauro Carvalho Chehab authored
Tested on x64 with a bttv board. Most Get ioctls are fixed. The only non-completely working one is VIDIOCGAUDIO. All other IOR ioctls give the same results on x86_64 and i386 architectures. Thanks to Alastair Poole <netstar@gatheringofgray.com> for part of this patch and tests on ppc64. Signed-off-by:
Alastair Poole <netstar@gatheringofgray.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Patrick Boettcher authored
Removed and commented a small debug function. Signed-off-by:
Patrick Boettcher <pb@linuxtv.org> Signed-off-by:
-
matthieu castet authored
The VGA was not turned on after calling sleep. This lead to bad performance in difficult areas. Signed-off-by:
matthieu castet <castet.matthieu@free.fr> Signed-off-by:
-
Patrick Boettcher authored
Another stupid fix for attaching the DiB3000MC. == 0 instead of != 0. Signed-off-by:
-
Patrick Boettcher authored
DiB3000MC: set FE to NULL after being freed Signed-off-by:
-
Klaus Frahm authored
A new revision of the Avermedia A800 does not reenumerate after download the firmware. Signed-off-by:
Klaus Frahm <frahm@irsamc.ups-tlse.fr> Signed-off-by:
Martin Habbecke <M.Habbecke@gmx.de> Signed-off-by:
-
Patrick Boettcher authored
Thomas Rokamp and others are reporting: "I have now with success extracted a working firmware for the 93004 rev. C1A2." This patch increments the firmware version to 2. Signed-off-by:
-
Patrick Boettcher authored
Flynn Marquardt found out that there is problem with the new dib3000mc-driver when using with the real dib3000mc. It resulted in a segfault. Fixed two things: use the correct I2C address and do not attach a tuner, when the demod was previously failing. Signed-off-by:
-
Patrick Boettcher authored
The first commit omitted the common-code and header-files. Signed-off-by:
-
Patrick Boettcher authored
A complete rewrite of the DiB3000MC/P driver has been done. It is now much more easy to maintain and to get improvements inside. Additionally the tuning time has been reduced and the usage of the driver is much more understandable now. Signed-off-by:
Patrick Boettcher <pboettcher@dibcom.fr> Signed-off-by:
Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr> Signed-off-by:
-
Patrick Boettcher authored
removing the dib3000-common-module. The common stuff is not common anymore - it will be only used by the 3000mb-driver. A new 3000mc/p-driver will be added which will share common stuff with dib7000. Signed-off-by:
-
Olivier DANET authored
new tuner api minor fixes for tuning Signed-off-by:
Olivier DANET <odanet@caramail.com> Signed-off-by:
-
Patrick Boettcher authored
When debugging was disabled at lot of empty lines where printed anyway. Reported by Rolf Ahrenberg and Sergei Haller. Signed-off-by:
-
Patrick Boettcher authored
Some minor code cleanups and added the MT2060 to new v4l-dvb-build-system, preliminarily under dvb/frontends. Signed-off-by:
-
Sergei Haller authored
+ Added support for the remote control shipped with the pen drive size DVB-T receiver [ID 10b8:0bc7 DiBcom DiBcom USB2.0 DVB-T reference design (MOD3000P)] Signed-off-by:
Sergei Haller <sergei@sergei-haller.de> Signed-off-by:
-
Patrick Boettcher authored
- AGC gain set to 3 - The tuning sequence has been changed to match the DibCom driver ( from I2C spy captures ) - For LITE-ON adapters : The IF1 frequency is now tuned according to the calibration values stored in EEPROM. Signed-off-by:
-
Olivier DANET authored
Adding the USB ids for the LeadTek clone of the STK3000P-ref-design. Signed-off-by:
-
Patrick Boettcher authored
Adding the USB IDs to dibusb-mc.c for the Artec T14 USB Stick based on STK3000P reference design. Thanks to Thomas Rabe testing. Signed-off-by:
-
Patrick Boettcher authored
- some coding style fixes for newly added mt2060 - moved agc-config from fixed values in dib3000mc to configurable ones - whitespace clean-ups for usb-id-file Signed-off-by:
-
Olivier DANET authored
- MT2060 tuner driver - Added support for some USB DVB-T devices based on Dib3000P Signed-off-by:
-
Chris Pascoe authored
Address another case where the test in dvb-pll to see if a tuner's PLL responds when attaching may fail. Signed-off-by:
Chris Pascoe <c.pascoe@itee.uq.edu.au> Signed-off-by:
-
Michael Krufky authored
This patch cleans up some whitespace problems after the dvb_attach changes in cx88-dvb.c and saa7134-dvb.c, and converts some capitalized i2c address constants to lowercase. Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Michael Krufky authored
The test in dvb-pll to see if a tuner's PLL responds when attaching fails on NXT2004 based boards before the firmware is loaded. This patch allows us to avoid this test by not passing an I2C bus handle to the dvb_pll_attach routine, just as Chris Pascoe has done for MT352 and ZL10353 based boards when used in cx88-dvb. Signed-off-by:
-
Chris Pascoe authored
Typical wiring of MT352 and ZL10353 based tuners differs from dvb-pll's expectation that the PLL is directly accessible. On these boards, the PLL is actually hidden behind the demodulator, and as such can only be accessed via the demodulator's interface. It was failing to communicate with the PLL during an attach test and subsequently not connecting the tuner ops. By passing a NULL I2C bus handle to dvb_pll_attach, this accessibility check can be bypassed. Do this for the affected boards. Also fix a possible NULL dereference at sleep time, which would otherwise be exposed by this change. Signed-off-by:
Andrew de Quincey <adq_dvb@lidskialf.net> Acked-by:
-
Yeasah Pell authored
Change this card to use HW ALGO tuning Signed-off-by:
Yeasah Pell <yeasah@schwide.com> Signed-off-by:
-
Yeasah Pell authored
Change the bit error counter configuration to be the actual BER. Originally it was reporting UCB. Signed-off-by:
-
Yeasah Pell authored
Set the Soft decision threshold properly for the specified FEC Signed-off-by:
-
Manu Abraham authored
Signed-off-by:
-
Andrew de Quincey authored
The tda826x detection was (correctly) cleaned up earlier, but unfortunately changing the number of received i2c messages from 2 -> 1 was missed. This fixes it. Signed-off-by:
-
Andrew de Quincey authored
Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Just a few adjustments were required on those drivers to be V4L2 compliant. Signed-off-by: -
Hans Verkuil authored
Signed-off-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Dmitry Torokhov authored
Compile-tested only (no hardware) Signed-off-by:
Dmitry Torokhov <dtor@mail.ru> Signed-off-by:
-
Alan Cox authored
Signed-off-by:
Alan Cox <alan@redhat.com> Signed-off-by:
-
Hans J. Koch authored
This is a card with RDS capabilities. RDS specifications didn't change from V4L1 to V4L2, so that part should be OK. This patch changed the following stuff: * The device can be opened multiple times. That's necessary because there are at least a radio application and an RDS application (rdsd) that want to open() the device. * Added a poll() function. Every character device should have that, and rdsd expects it as it uses select() on that file descriptor. * Converted the ioctls to V4L2. MUTE is not implemented correctly as the card doesn't seem to have a special bit for that. Probably there are a few more ioctls that should at least return 0 or an error. As I do not own such a card, I couldn't test anything. If there is anybody out there who owns such an ancient card, please test and report. I just checked that the code compiles. Signed-off-by:
Hans J. Koch <koch@hjk-az.de> Signed-off-by:
-
