- 20 May, 2010 40 commits
-
-
Johan Hovold authored
Use generic read implementation and use process_read_urb to do device specific processing (handle line status). Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Johan Hovold authored
Add process_read_urb to usb_serial_driver so that a driver can rely on the generic read (and throttle) mechanism but still do device specific processing of incoming data (such as adding tty_flags before pushing to line discipline). The default generic implementation handles sysrq for consoles but otherwise simply pushes to tty. Signed-off-by:
-
Johan Hovold authored
Always process and flush read urb, but only resubmit when not throttled. The new tty-layer supply plenty of slack so there is really no need to cache and delay processing of a single urb while throttled. Note that unthrottle now submits using GFP_KERNEL as we are not in atomic context (so there is no need to save irq state either). Note also that the process_read_urb function could be added to usb_serial_driver should any driver need to do any device specific processing. Signed-off-by:
-
Johan Hovold authored
There is no need to initialise the read urb as this is done at port probe. Signed-off-by:
-
Johan Hovold authored
The generic read and write bulk urbs are initialised when allocated in usb_serial_probe. The only field that needs to be updated after that is the transfer_buffer_length of the write urb. Signed-off-by:
-
Johan Hovold authored
Use the already exported function for submitting the read urb associated with a usb_serial_port. Make sure it returns the result of usb_submit_urb and rename to the more descriptive usb_serial_generic_submit_read_urb. Signed-off-by:
-
Johan Hovold authored
Export usb_serial_generic_close so that drivers can easily kill the read and write urb and make sure that the write fifo is reset. Signed-off-by:
-
Johan Hovold authored
Make sure fifo is emptied on close. Signed-off-by:
-
Johan Hovold authored
On errors the fifo was reset without any locking. This could race with write which do kfifo_put and perhaps also chars_in_buffer and write_room. Every other access to the fifo is protected using the port lock so better add it to the error path as well. Signed-off-by:
-
Johan Hovold authored
Make sure chars_in_buffer accounts also for data in host stack queues. This fixes the problem with tty_wait_until_sent returning too soon at close which could cause the final write urb to be cancelled. Reported-by:
Pete Zaitcev <zaitcev@redhat.com> Signed-off-by:
-
Johan Hovold authored
The pl2303 requires a bulk-in buffer larger than endpoint size to keep up at high baudrates without loosing data. Signed-off-by:
-
Johan Hovold authored
Increase the bulk-out buffer size from 64 to 256 byte. This gives a significant increase in throughput already at 1Mbaud as well as lowered CPU usage. The buffer is big enough to keep up also at 3Mbaud (128b would not suffice). 64b 256b 921k: 640 KB/s 870 KB/s 3M: 640 KB/s 2520 KB/s Signed-off-by: -
Johan Hovold authored
The cp210x requires a bulk-in buffer larger than endpoint size to keep up at high baudrates without loosing data. Signed-off-by:
-
Johan Hovold authored
Increase the bulk-out buffer size from 64 to 256 byte. This gives a significant increase in throughput already at 1Mbaud (e.g. 710 instead of 640 KB/s) as well as lowered CPU usage. Signed-off-by:
-
Johan Hovold authored
Allow drivers to define custom bulk in/out buffer sizes in struct usb_serial_driver. If not set, fall back to the default buffer size which matches the endpoint size. Three drivers are currently freeing the pre-allocated buffers and allocating larger ones to achieve this at port probe (ftdi_sio) or even at port open (ipaq and iuu_phoenix), which needless to say is suboptimal. Signed-off-by:
-
Hans de Goede authored
Add a new quirk USB_QUIRK_HONOR_BNUMINTERFACES, when this quirk is set and a device has more interface descriptors in a configuration then it claims to have in config->bNumInterfaces, ignore all additional interfaces. This is needed for devices which try to hide unused interfaces by only lowering config->bNumInterfaces, and which can't handle if you try to talk to the "hidden" interfaces. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Randy Dunlap authored
Fix build error when CONFIG_MAGIC_SYSRQ is not enabled: drivers/usb/serial/generic.c:566: error: implicit declaration of function 'handle_sysrq' Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Vijay Kumar authored
Add ZIO Motherboard USB serial interface driver. Signed-off-by:
Vijay Kumar B. <vijaykumar@zilogic.com> Signed-off-by:
-
Jason Wessel authored
The usb console code has had a long standing problem of not being able to pass the baud rate from the kernel argument console=ttyUSB0,BAUD down to the initial tty open, unless you were willing to settle for 9600 baud. The solution is to directly use tty_init_termios() in usb_console_setup() as this will preserve any changes to the initial termios setting on future opens. CC: Alan Cox <alan@linux.intel.com> CC: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Jason Wessel <jason.wessel@windriver.com> Signed-off-by:
-
Michal Nazarewicz authored
"Static" buffers in fsg_buffhd structure (ie. fields which are arrays rather then pointers to dynamically allocated memory) are not aligned to any "big" power of two which may lead to poor DMA performance (copying "by hand" of head or tail) or no DMA at all even if otherwise hardware supports it. Therefore, this patch makes mass storage function use kmalloc()ed buffers which are (because of their size) page aligned (which should be enough for any hardware). Signed-off-by:
Michal Nazarewicz <m.nazarewicz@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
-
Felipe Balbi authored
... and simplify the was we read/write from/to DMA COUNT register. Signed-off-by:
Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by:
-
Felipe Balbi authored
we can support the musb-specific test modes on the vendor specific range of test selector as stated on USB Specification Table 9-7 Test Mode Selectors. Signed-off-by:
-
Felipe Balbi authored
for now only a simple register dump entry (which can be rather useful on debugging) and a way to start test modes. Signed-off-by:
-
Cliff Cai authored
Rather than hardcoding the gpio levels for vrsel, allow the platform resources to handle this so boards can be active high or low. Signed-off-by:
Cliff Cai <cliff.cai@analog.com> Signed-off-by:
Mike Frysinger <vapier@gentoo.org> Signed-off-by:
-
Maulik Mankad authored
This patch adds CONFIG_ARCH_OMAP4 macro within MUSB driver. Signed-off-by:
Maulik Mankad <x0082077@ti.com> Cc: David Brownell <david-b@pacbell.net> Cc: Sergei Shtylyov <sshtylyov@mvista.com> Cc: Olof Johansson <olof@lixom.net> Signed-off-by:
-
Maulik Mankad authored
This patch updates the Makefile to build the MUSB driver for OMAP4. It also sets the Kconfig options for OMAP4. Signed-off-by:
-
Maulik Mankad authored
Program the OTG_INTERFSEL register based on transcevier type passed from board file. Adapt signature of musb_platform_init() function for davinci, blackfin and tusb6010. Signed-off-by:
-
Felipe Balbi authored
boards might want to optimize their fifo configuration to the particular needs of that specific board. Allow that by moving all related data structures to <linux/usb/musb.h> Signed-off-by:
-
Jason Wessel authored
Replace all instances of using the console variable in struct usb_serial_port with the struct tty_port version. CC: Alan Cox <alan@linux.intel.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Oliver Neukum <oliver@neukum.org> CC: Andrew Morton <akpm@linux-foundation.org> CC: linux-usb@vger.kernel.org CC: linux-kernel@vger.kernel.org Signed-off-by:
-
Manuel Lauss authored
I've been running variations of this patch for well over a year now; my usual zoo of test devices didn't trigger any ill effects even under heavy load. As a nice sideeffect idle-wakeups are reduced from 20/s to about 2/s (EHCI hub with mouse and kbd). Signed-off-by:
Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by:
-
Alan Stern authored
This patch (as1350) removes all usages of coherent buffers for USB control-request setup-packet buffers. There's no good reason to reserve coherent memory for these things; control requests are hardly ever used in large quantity (the major exception is firmware transfers, and they aren't time-critical). Furthermore, only seven drivers used it. We might as well always use streaming DMA mappings for setup-packet buffers, and remove some extra complexity from usbcore. The DMA-mapping portion of hcd.c is currently in flux. A separate patch will be submitted to remove support for URB_NO_SETUP_DMA_MAP after everything else settles down. The removal should go smoothly, as by then nobody will be using it. Signed-off-by:
-
Alan Stern authored
This patch (as1349b) clears up the confusion in many USB host controller drivers between port features and port statuses. In mosty cases it's true that the status bit is in the position given by the corresponding feature value, but that's not always true and it's not guaranteed in the USB spec. There's no functional change, just replacing expressions of the form (1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value. Signed-off-by:
-
Alan Stern authored
This patch (as1348) removes the bogus USB_PORT_FEAT_{HIGHSPEED,SUPERSPEED} symbols from ch11.h. No such features are defined by the USB spec. (There is a PORT_LOWSPEED feature, but the spec doesn't mention it except to say that host software should never use it.) The speed indicators are port statuses, not port features. As a temporary workaround for the xhci-hcd driver, a fictional USB_PORT_STAT_SUPER_SPEED symbol is added. Signed-off-by: -
Huang Weiyi authored
Remove duplicated #include('s) in drivers/usb/core/hcd.c Signed-off-by:Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by:
-
Ian Munsie authored
The compiler throws the following warning when compiling for a PowerPC 64 bit machine: drivers/usb/storage/isd200.c:580: warning: the frame size of 2208 bytes is larger than 2048 bytes There is a struct scsi_device which is placed on the stack and is largely responsible for such wastage. The struct is just a dummy struct filled with NULLs and set as the scsi_cmnd->device to make the usb_stor_Bulk_transport function happy. This patch makes the struct static, so that it is never placed onto the stack and silences the compiler warning. Signed-off-by:
Ian Munsie <imunsie@au.ibm.com> Signed-off-by:
-
Randy Dunlap authored
Fix usb/class sparse warnings: drivers/usb/class/cdc-acm.h:128:34: error: dubious one-bit signed bitfield drivers/usb/class/cdc-acm.h:129:24: error: dubious one-bit signed bitfield Signed-off-by:
-
Alessio Igor Bogani authored
Seems to me that BKL is not needed here because necessary locking is already provided by mutex sisusb->lock. Also change the returned value to long. Signed-off-by:
Alessio Igor Bogani <abogani@texware.it> Signed-off-by:
-
Eric Lescouet authored
Base on inputs from Alan Stern, split the hub.h header into: - new ch11.h header (most of it) containing constants and structures from chapter 11 of the USB 2.0 spec. - a small remaining part being merged into hcd.h. Signed-of-by:
Eric Lescouet <eric@lescouet.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Eric Lescouet authored
The usbcore headers: hcd.h and hub.h are shared between usbcore, HCDs and a couple of other drivers (e.g. USBIP modules). So, it makes sense to move them into a more public location and to cleanup dependency of those modules on kernel internal headers. This patch moves hub.h from drivers/usb/core into include/linux/usb/ Signed-of-by:
-
Eric Lescouet authored
The usbcore headers: hcd.h and hub.h are shared between usbcore, HCDs and a couple of other drivers (e.g. USBIP modules). So, it makes sense to move them into a more public location and to cleanup dependency of those modules on kernel internal headers. This patch moves hcd.h from drivers/usb/core into include/linux/usb/ Signed-of-by:
-
