When multiple instances of the same MHI product are present in a system,
we can see a splat from mhi_create_devices() - "sysfs: cannot create
duplicate filename".

This is because the device names assigned to the MHI channel devices are
non-unique.  They consist of the channel's name, and the channel's pipe
id.  For identical products, each instance is going to have the same
set of channel (both in name and pipe id).

To fix this, we prepend the device name of the parent device that the
MHI channels belong to.  Since different instances of the same product
should have unique device names, this makes the MHI channel devices for
each product also unique.

Additionally, remove the pipe id from the MHI channel device name.  This
is an internal detail to the MHI product that provides little value, and
imposes too much device specific internal details to userspace.  It is
expected that channel with a specific name (ie "SAHARA") has a specific
client, and it does not matter what pipe id that channel is enumerated on.
The pipe id is an internal detail between the MHI bus, and the hardware.
The client is not expected to make decisions based on the pipe id, and to
do so would require the client to have intimate knowledge of the hardware,
which is inappropiate as it may violate the layering provided by the MHI
bus.  The limitation of doing this is that each product may only have one
instance of a channel by a unique name.  This limitation is appropriate
given the usecases of MHI channels.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-7-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a typo - "runtimet" should be "runtime".  Fix it.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-6-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When reading or writing MHI registers, the core assumes that the physical
link is a memory mapped PCI link.  This assumption may not hold for all
MHI devices.  The controller knows what is the physical link (ie PCI, I2C,
SPI, etc), and therefore knows the proper methods to access that link.
The controller can also handle link specific error scenarios, such as
reading -1 when the PCI link went down.

Therefore, it is appropriate that the MHI core requests the controller to
make register accesses on behalf of the core, which abstracts the core
from link specifics, and end up removing an unnecessary assumption.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-5-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the MHI core detects invalid data due to a PCI read, it calls into
the controller via link_status() to double check that the link is infact
down.  All in all, this is pretty pointless, and racy.  There are no good
reasons for this, and only drawbacks.

Its pointless because chances are, the controller is going to do the same
thing to determine if the link is down - attempt a PCI access and compare
the result.  This does not make the link status decision any smarter.

Its racy because its possible that the link was down at the time of the
MHI core access, but then recovered before the controller access.  In this
case, the controller will indicate the link is not down, and the MHI core
will precede to use a bad value as the MHI core does not attempt to retry
the access.

Retrying the access in the MHI core is a bad idea because again, it is
racy - what if the link is down again?  Furthermore, there may be some
higher level state associated with the link status, that is now invalid
because the link went down.

The only reason why the MHI core could see "invalid" data when doing a PCI
access, that is actually valid, is if the register actually contained the
PCI spec defined sentinel for an invalid access.  In this case, it is
arguable that the MHI implementation broken, and should be fixed, not
worked around.

Therefore, remove the link_status() callback before anyone attempts to
implement it.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-4-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Powerdown is necessary if mhi_sync_power_up fails due to a timeout, to
clean up the resources.  Otherwise a BUG could be triggered when
attempting to clean up MSIs because the IRQ is still active from a
request_irq().
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-3-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

With the current parsing of mhi_flags, the following statement always
return false:

eob = !!(flags & MHI_EOB);

This is due to the fact that 'enum mhi_flags' starts with index 0 and we
are using direct AND operation to extract each bit. Fix this by using
BIT() macros for defining the flags so that the reset of the code need not
be touched.

Fixes: 189ff97c ("bus: mhi: core: Add support for data transfer")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200430190555.32741-2-manivannan.sadhasivam@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Disable the MEI driver on LBG SPS (server) platforms, some corner
flows such as recovery mode does not work, and the driver
doesn't have working use cases.

Cc: <stable@vger.kernel.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20200428211200.12200-1-tomas.winkler@intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'phy-for-5.7-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-linus

phy: for 5.7 -rc

*) Update MAINTAINER to include Vinod Koul as co-maintainer of PHY
*) Fix Kconfig dependencies in seen with PHY_TEGRA_XUSB
*) Re-add "qcom,sdm845-qusb2-phy" compatible in phy-qcom-qusb2.c to
   make it work with existing dtbs
*) Move clock enable from ->poweron() to ->init() in Qualcomm
   usb-hs-28nm driver to initialize HW in ->init()
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

* tag 'phy-for-5.7-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
  phy: qualcomm: usb-hs-28nm: Prepare clocks in init
  MAINTAINERS: Add Vinod Koul as Generic PHY co-maintainer
  phy: qcom-qusb2: Re add "qcom,sdm845-qusb2-phy" compat string
  phy: tegra: Select USB_COMMON for usb_get_maximum_speed()

The AHB clock must be on for qcom_snps_hsphy_init() to be able to write
the initialization sequence to the hardware, so move the clock
enablement to phy init and exit.

Fixes: 67b27dbe ("phy: qualcomm: Add Synopsys 28nm Hi-Speed USB PHY driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add Vinod Koul as Generic PHY Subsystem co-maintainer and move
the linux-phy to a shared repository.

Cc: Vinod Koul <vkoul@kernel.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Fix the following warning:

Move the static keyword to the front of declaration of sdm845_icc_osm_l3
sdm845_aggre1_noc sc7180_icc_osm_l3 sdm845_aggre2_noc sdm845_config_noc
sdm845_dc_noc sdm845_gladiator_noc sdm845_mem_noc sdm845_mmss_noc and
sdm845_system_noc, resolve the following compiler warning that can be
when building with warnings enabled (W=1):

drivers/interconnect/qcom/osm-l3.c:81:1: warning:
 const static struct qcom_icc_desc sdm845_icc_osm_l3 = {
drivers/interconnect/qcom/osm-l3.c:94:1: warning:
 const static struct qcom_icc_desc sc7180_icc_osm_l3 = {
drivers/interconnect/qcom/sdm845.c:195:1: warning:
 const static struct qcom_icc_desc sdm845_aggre1_noc = {
drivers/interconnect/qcom/sdm845.c:223:1: warning:
 const static struct qcom_icc_desc sdm845_aggre2_noc = {
drivers/interconnect/qcom/sdm845.c:284:1: warning:
 const static struct qcom_icc_desc sdm845_config_noc = {
drivers/interconnect/qcom/sdm845.c:300:1: warning:
 const static struct qcom_icc_desc sdm845_dc_noc = {
drivers/interconnect/qcom/sdm845.c:318:1: warning:
 const static struct qcom_icc_desc sdm845_gladiator_noc = {
drivers/interconnect/qcom/sdm845.c:353:1: warning:
 const static struct qcom_icc_desc sdm845_mem_noc = {
drivers/interconnect/qcom/sdm845.c:387:1: warning:
 const static struct qcom_icc_desc sdm845_mmss_noc = {
drivers/interconnect/qcom/sdm845.c:433:1: warning:
 const static struct qcom_icc_desc sdm845_system_noc = {
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: ChenTao <chentao107@huawei.com>
Link: https://lore.kernel.org/r/20200423132142.45174-1-chentao107@huawei.comSigned-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20200429101904.5771-2-georgi.djakov@linaro.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch replaces function module_init() with subsys_initcall().
It is needed to ensure that the core module of the driver is
initialized before a component tries to register with the core. This
leads to a NULL pointer dereference if the driver is configured as
in-tree.
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/1587741394-22021-1-git-send-email-christian.gromm@microchip.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The mhi_alloc_device() function never returns NULL, it returns error
pointers.

Fixes: da1c4f85 ("bus: mhi: core: Add support for creating and destroying MHI devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200407093133.GM68494@mwandaSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a regression in 5.7-rc1+

In commit 8fe75cd4 ("phy: qcom-qusb2: Add generic QUSB2 V2
PHY support"), the change was made to add "qcom,qusb2-v2-phy"
as a generic compat string. However the change also removed
the "qcom,sdm845-qusb2-phy" compat string, which is documented
in the binding and already in use.

This patch re-adds the "qcom,sdm845-qusb2-phy" compat string
which allows the driver to continue to work with existing dts
entries such as found on the db845c.

Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Manu Gautam <mgautam@codeaurora.org>
Cc: Sandeep Maheswaram <sanm@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes: 8fe75cd4 ("phy: qcom-qusb2: Add generic QUSB2 V2 PHY support")
Reported-by: YongQin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Pull cifs fixes from Steve French:
 "Five cifs/smb3 fixes:two for DFS reconnect failover, one lease fix for
  stable and the others to fix a missing spinlock during reconnect"

* tag '5.7-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix uninitialised lease_key in open_shroot()
  cifs: ensure correct super block for DFS reconnect
  cifs: do not share tcons with DFS
  cifs: minor update to comments around the cifs_tcp_ses_lock mutex
  cifs: protect updating server->dstaddr with a spinlock

Pull USB fixes from Greg KH:
 "Here are a number of USB driver fixes for 5.7-rc3.

  Nothing huge, just the usual collection of:

   - xhci fixes

   - gadget driver fixes

   - syzkaller fuzzing fixes

   - new device ids and DT bindings

   - new quirks added for broken devices

  A few of the gadget driver fixes show up twice here as they were
  applied to my branch, and also by Felipe to his branch which I then
  pulled in as we got out of sync a bit.

  All of these have been in linux-next with no reported issues"

* tag 'usb-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
  USB: sisusbvga: Change port variable from signed to unsigned
  usb-storage: Add unusual_devs entry for JMicron JMS566
  USB: hub: Revert commit bd0e6c96 ("usb: hub: try old enumeration scheme first for high speed devices")
  USB: hub: Fix handling of connect changes during sleep
  usb: typec: altmode: Fix typec_altmode_get_partner sometimes returning an invalid pointer
  xhci: Don't clear hub TT buffer on ep0 protocol stall
  xhci: prevent bus suspend if a roothub port detected a over-current condition
  xhci: Fix handling halted endpoint even if endpoint ring appears empty
  usb: raw-gadget: Fix copy_to/from_user() checks
  usb: raw-gadget: fix raw_event_queue_fetch locking
  usb: gadget: udc: atmel: Fix vbus disconnect handling
  usb: dwc3: gadget: Fix request completion check
  USB: Add USB_QUIRK_DELAY_CTRL_MSG and USB_QUIRK_DELAY_INIT for Corsair K70 RGB RAPIDFIRE
  phy: tegra: Select USB_COMMON for usb_get_maximum_speed()
  usb: typec: tcpm: Ignore CC and vbus changes in PORT_RESET change
  usb: f_fs: Clear OS Extended descriptor counts to zero in ffs_data_reset()
  cdc-acm: introduce a cool down
  cdc-acm: close race betrween suspend() and acm_softint
  UAS: fix deadlock in error handling and PM flushing work
  UAS: no use logging any details in case of ENODEV
  ...

Pull tty/serial fixes from Greg KH:
 "Here are some tty and serial driver fixes for 5.7-rc3.

  The "largest" in here are a number of reverts for previous changes to
  the uartps serial driver that turned out to not be a good idea at all.

  The others are just small fixes found by people and tools. Included in
  here is a much-reported symbol export needed by previous changes that
  happened in 5.7-rc1. All of these have been in linux-next for a while
  with no reported issues"

* tag 'tty-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: hvc: fix buffer overflow during hvc_alloc().
  tty: rocket, avoid OOB access
  tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart
  vt: don't hardcode the mem allocation upper bound
  tty: serial: owl: add "much needed" clk_prepare_enable()
  vt: don't use kmalloc() for the unicode screen buffer
  tty/sysrq: Export sysrq_mask(), sysrq_toggle_support()
  serial: sh-sci: Make sure status register SCxSR is read in correct sequence
  serial: sunhv: Initialize lock for non-registered console
  Revert "serial: uartps: Register own uart console and driver structures"
  Revert "serial: uartps: Move Port ID to device data structure"
  Revert "serial: uartps: Change uart ID port allocation"
  Revert "serial: uartps: Do not allow use aliases >= MAX_UART_INSTANCES"
  Revert "serial: uartps: Fix error path when alloc failed"
  Revert "serial: uartps: Use the same dynamic major number for all ports"
  Revert "serial: uartps: Fix uartps_major handling"

Pull char/misc driver fixes from Greg KH:
 "Here are 4 small misc driver fixes for 5.7-rc3:

   - mei driver fix

   - interconnect driver fix

   - two fpga driver fixes

  All have been in linux-next with no reported issues"

* tag 'char-misc-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  interconnect: qcom: Fix uninitialized tcs_cmd::wait
  mei: me: fix irq number stored in hw struct
  fpga: dfl: pci: fix return value of cci_pci_sriov_configure
  fpga: zynq: Remove clk_get error message for probe defer

Pull staging/IIO driver fixes from Greg KH:
 "Here are some small staging and IIO driver fixes for 5.7-rc3

  Lots of tiny things for reported issues in staging and IIO drivers,
  including a counter driver fix as well (the iio drivers seem to be
  tied to those). Full details of the fixes are in the shortlog.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'staging-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (27 commits)
  staging: vt6656: Fix calling conditions of vnt_set_bss_mode
  staging: comedi: Fix comedi_device refcnt leak in comedi_open
  staging: vt6656: Fix pairwise key entry save.
  staging: vt6656: Fix drivers TBTT timing counter.
  staging: vt6656: Don't set RCR_MULTICAST or RCR_BROADCAST by default.
  MAINTAINERS: remove Stefan Popa's email
  iio: adc: ad7192: fix null pointer de-reference crash during probe
  iio: core: remove extra semi-colon from devm_iio_device_register() macro
  iio: adc: ti-ads8344: properly byte swap value
  iio: imu: inv_mpu6050: fix suspend/resume with runtime power
  iio: st_sensors: rely on odr mask to know if odr can be set
  iio: xilinx-xadc: Make sure not exceed maximum samplerate
  iio: xilinx-xadc: Fix sequencer configuration for aux channels in simultaneous mode
  iio: xilinx-xadc: Fix clearing interrupt when enabling trigger
  iio: xilinx-xadc: Fix ADC-B powerdown
  iio: dac: ad5770r: fix off-by-one check on maximum number of channels
  iio: imu: st_lsm6dsx: flush hw FIFO before resetting the device
  iio: core: Fix handling of 'dB'
  dt-bindings: iio: adc: stm32-adc: fix id relative path
  counter: 104-quad-8: Add lock guards - generic interface
  ...

Pull driver core fixes from Greg KH:
 "Here are some small firmware/driver core/debugfs fixes for 5.7-rc3.

  The debugfs change is now possible as now the last users of
  debugfs_create_u32() have been fixed up in the different trees that
  got merged into 5.7-rc1, and I don't want it creeping back in.

  The firmware changes did cause a regression in linux-next, so the
  final patch here reverts part of that, re-exporting the symbol to
  resolve that issue. All of these patches, with the exception of the
  final one, have been in linux-next with only that one reported issue"

* tag 'driver-core-5.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  firmware_loader: revert removal of the fw_fallback_config export
  debugfs: remove return value of debugfs_create_u32()
  firmware_loader: remove unused exports
  firmware: imx: fix compile-testing

Pull s390 fixes from Vasily Gorbik:

 - Add a few notrace annotations to avoid potential crashes when
   switching ftrace tracers.

 - Avoid setting affinity for floating irqs in pci code.

 - Fix build issue found by kbuild test robot.

* tag 's390-5.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/protvirt: fix compilation issue
  s390/pci: do not set affinity for floating irqs
  s390/ftrace: fix potential crashes when switching tracers

Pull powerpc fixes from Michael Ellerman:

 - One important fix for a bug in the way we find the cache-line size
   from the device tree, which was leading to the wrong size being
   reported to userspace on some platforms.

 - A fix for 8xx STRICT_KERNEL_RWX which was leaving TLB entries around
   leading to a window at boot when the strict mapping wasn't enforced.

 - A fix to enable our KUAP (kernel user access prevention) debugging on
   PPC32.

 - A build fix for clang in lib/mpi.

Thanks to: Chris Packham, Christophe Leroy, Nathan Chancellor, Qian Cai.

* tag 'powerpc-5.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  lib/mpi: Fix building for powerpc with clang
  powerpc/mm: Fix CONFIG_PPC_KUAP_DEBUG on PPC32
  powerpc/8xx: Fix STRICT_KERNEL_RWX startup test failure
  powerpc/setup_64: Set cache-line-size based on cache-block-size

Pull more Devicetree fixes from Rob Herring:
 "A couple of schema and kbuild fixes"

* tag 'devicetree-fixes-for-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: phy: qcom-qusb2: Fix defaults
  dt-bindings: Fix erroneous 'additionalProperties'
  dt-bindings: Fix command line length limit calling dt-mk-schema
  dt-bindings: Re-enable core schemas for dtbs_check

Christoph's patch removed two unsused exported symbols, however, one
symbol is used by the firmware_loader itself.  If CONFIG_FW_LOADER=m so
the firmware_loader is modular but CONFIG_FW_LOADER_USER_HELPER=y we fail
the build at mostpost.

ERROR: modpost: "fw_fallback_config" [drivers/base/firmware_loader/firmware_class.ko] undefined!

This happens because the variable fw_fallback_config is built into the
kernel if CONFIG_FW_LOADER_USER_HELPER=y always, so we need to grant
access to the firmware loader module by exporting it.

Revert only one hunk from his patch.

Fixes: 73960473 ("firmware_loader: remove unused exports")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20200424184916.22843-1-mcgrof@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull pid leak fix from Eric Biederman:
 "Oleg noticed that put_pid(thread_pid) was not getting called when proc
  was not compiled in.

  Let's get that fixed before 5.7 is released and causes problems for
  anyone"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  proc: Put thread_pid in release_task not proc_flush_pid

Pull timer fixlet from Ingo Molnar:
 "A single fix for a comment that may show up in DocBook output"

* tag 'timers-urgent-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  vdso/datapage: Use correct clock mode name in comment

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes:

   - an uclamp accounting fix

   - three frequency invariance fixes and a readability improvement"

* tag 'sched-urgent-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Fix reset-on-fork from RT with uclamp
  x86, sched: Move check for CPU type to caller function
  x86, sched: Don't enable static key when starting secondary CPUs
  x86, sched: Account for CPUs with less than 4 cores in freq. invariance
  x86, sched: Bail out of frequency invariance if base frequency is unknown

Pull perf fixes from Ingo Molnar:
 "Two changes:

   - fix exit event records

   - extend x86 PMU driver enumeration to add Intel Jasper Lake CPU
     support"

* tag 'perf-urgent-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: fix parent pid/tid in task exit events
  perf/x86/cstate: Add Jasper Lake CPU support

Pull objtool fixes from Ingo Molnar:
 "Two fixes: fix an off-by-one bug, and fix 32-bit builds on 64-bit
  systems"

* tag 'objtool-urgent-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix off-by-one in symbol_by_offset()
  objtool: Fix 32bit cross builds

The kernel fails to compile with CONFIG_PROTECTED_VIRTUALIZATION_GUEST
set but CONFIG_KVM unset.

This patch fixes the issue by making the needed variable always available.

Link: https://lkml.kernel.org/r/20200423120114.2027410-1-imbrenda@linux.ibm.com
Fixes: a0f60f84 ("s390/protvirt: Add sysfs firmware interface for Ultravisor information")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Philipp Rudo <prudo@linux.ibm.com>
Suggested-by: Philipp Rudo <prudo@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

Pull networking fixes from David Miller:

 1) Fix memory leak in netfilter flowtable, from Roi Dayan.

 2) Ref-count leaks in netrom and tipc, from Xiyu Yang.

 3) Fix warning when mptcp socket is never accepted before close, from
    Florian Westphal.

 4) Missed locking in ovs_ct_exit(), from Tonghao Zhang.

 5) Fix large delays during PTP synchornization in cxgb4, from Rahul
    Lakkireddy.

 6) team_mode_get() can hang, from Taehee Yoo.

 7) Need to use kvzalloc() when allocating fw tracer in mlx5 driver,
    from Niklas Schnelle.

 8) Fix handling of bpf XADD on BTF memory, from Jann Horn.

 9) Fix BPF_STX/BPF_B encoding in x86 bpf jit, from Luke Nelson.

10) Missing queue memory release in iwlwifi pcie code, from Johannes
    Berg.

11) Fix NULL deref in macvlan device event, from Taehee Yoo.

12) Initialize lan87xx phy correctly, from Yuiko Oshino.

13) Fix looping between VRF and XFRM lookups, from David Ahern.

14) etf packet scheduler assumes all sockets are full sockets, which is
    not necessarily true. From Eric Dumazet.

15) Fix mptcp data_fin handling in RX path, from Paolo Abeni.

16) fib_select_default() needs to handle nexthop objects, from David
    Ahern.

17) Use GFP_ATOMIC under spinlock in mac80211_hwsim, from Wei Yongjun.

18) vxlan and geneve use wrong nlattr array, from Sabrina Dubroca.

19) Correct rx/tx stats in bcmgenet driver, from Doug Berger.

20) BPF_LDX zero-extension is encoded improperly in x86_32 bpf jit, fix
    from Luke Nelson.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (100 commits)
  selftests/bpf: Fix a couple of broken test_btf cases
  tools/runqslower: Ensure own vmlinux.h is picked up first
  bpf: Make bpf_link_fops static
  bpftool: Respect the -d option in struct_ops cmd
  selftests/bpf: Add test for freplace program with expected_attach_type
  bpf: Propagate expected_attach_type when verifying freplace programs
  bpf: Fix leak in LINK_UPDATE and enforce empty old_prog_fd
  bpf, x86_32: Fix logic error in BPF_LDX zero-extension
  bpf, x86_32: Fix clobbering of dst for BPF_JSET
  bpf, x86_32: Fix incorrect encoding in BPF_LDX zero-extension
  bpf: Fix reStructuredText markup
  net: systemport: suppress warnings on failed Rx SKB allocations
  net: bcmgenet: suppress warnings on failed Rx SKB allocations
  macsec: avoid to set wrong mtu
  mac80211: sta_info: Add lockdep condition for RCU list usage
  mac80211: populate debugfs only after cfg80211 init
  net: bcmgenet: correct per TX/RX ring statistics
  net: meth: remove spurious copyright text
  net: phy: bcm84881: clear settings on link down
  chcr: Fix CPU hard lockup
  ...

Alexei Starovoitov says:

====================
pull-request: bpf 2020-04-24

The following pull-request contains BPF updates for your *net* tree.

We've added 17 non-merge commits during the last 5 day(s) which contain
a total of 19 files changed, 203 insertions(+), 85 deletions(-).

The main changes are:

1) link_update fix, from Andrii.

2) libbpf get_xdp_id fix, from David.

3) xadd verifier fix, from Jann.

4) x86-32 JIT fixes, from Luke and Wang.

5) test_btf fix, from Stanislav.

6) freplace verifier fix, from Toke.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 51c39bb1 ("bpf: Introduce function-by-function verification")
introduced function linkage flag and changed the error message from
"vlen != 0" to "Invalid func linkage" and broke some fake BPF programs.

Adjust the test accordingly.

AFACT, the programs don't really need any arguments and only look
at BTF for maps, so let's drop the args altogether.

Before:
BTF raw test[103] (func (Non zero vlen)): do_test_raw:3703:FAIL expected
err_str:vlen != 0
magic: 0xeb9f
version: 1
flags: 0x0
hdr_len: 24
type_off: 0
type_len: 72
str_off: 72
str_len: 10
btf_total_size: 106
[1] INT (anon) size=4 bits_offset=0 nr_bits=32 encoding=SIGNED
[2] INT (anon) size=4 bits_offset=0 nr_bits=32 encoding=(none)
[3] FUNC_PROTO (anon) return=0 args=(1 a, 2 b)
[4] FUNC func type_id=3 Invalid func linkage

BTF libbpf test[1] (test_btf_haskv.o): libbpf: load bpf program failed:
Invalid argument
libbpf: -- BEGIN DUMP LOG ---
libbpf:
Validating test_long_fname_2() func#1...
Arg#0 type PTR in test_long_fname_2() is not supported yet.
processed 0 insns (limit 1000000) max_states_per_insn 0 total_states 0
peak_states 0 mark_read 0

libbpf: -- END LOG --
libbpf: failed to load program 'dummy_tracepoint'
libbpf: failed to load object 'test_btf_haskv.o'
do_test_file:4201:FAIL bpf_object__load: -4007
BTF libbpf test[2] (test_btf_newkv.o): libbpf: load bpf program failed:
Invalid argument
libbpf: -- BEGIN DUMP LOG ---
libbpf:
Validating test_long_fname_2() func#1...
Arg#0 type PTR in test_long_fname_2() is not supported yet.
processed 0 insns (limit 1000000) max_states_per_insn 0 total_states 0
peak_states 0 mark_read 0

libbpf: -- END LOG --
libbpf: failed to load program 'dummy_tracepoint'
libbpf: failed to load object 'test_btf_newkv.o'
do_test_file:4201:FAIL bpf_object__load: -4007
BTF libbpf test[3] (test_btf_nokv.o): libbpf: load bpf program failed:
Invalid argument
libbpf: -- BEGIN DUMP LOG ---
libbpf:
Validating test_long_fname_2() func#1...
Arg#0 type PTR in test_long_fname_2() is not supported yet.
processed 0 insns (limit 1000000) max_states_per_insn 0 total_states 0
peak_states 0 mark_read 0

libbpf: -- END LOG --
libbpf: failed to load program 'dummy_tracepoint'
libbpf: failed to load object 'test_btf_nokv.o'
do_test_file:4201:FAIL bpf_object__load: -4007

Fixes: 51c39bb1 ("bpf: Introduce function-by-function verification")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200422003753.124921-1-sdf@google.com

Reorder include paths to ensure that runqslower sources are picking up
vmlinux.h, generated by runqslower's own Makefile. When runqslower is built
from selftests/bpf, due to current -I$(BPF_INCLUDE) -I$(OUTPUT) ordering, it
might pick up not-yet-complete vmlinux.h, generated by selftests Makefile,
which could lead to compilation errors like [0]. So ensure that -I$(OUTPUT)
goes first and rely on runqslower's Makefile own dependency chain to ensure
vmlinux.h is properly completed before source code relying on it is compiled.

  [0] https://travis-ci.org/github/libbpf/libbpf/jobs/677905925Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200422012407.176303-1-andriin@fb.com

Fix the following sparse warning:

kernel/bpf/syscall.c:2289:30: warning: symbol 'bpf_link_fops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/1587609160-117806-1-git-send-email-zou_wei@huawei.com

In the prog cmd, the "-d" option turns on the verifier log.
This is missed in the "struct_ops" cmd and this patch fixes it.

Fixes: 65c93628 ("bpftool: Add struct_ops support")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20200424182911.1259355-1-kafai@fb.com

This adds a new selftest that tests the ability to attach an freplace
program to a program type that relies on the expected_attach_type of the
target program to pass verification.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/158773526831.293902.16011743438619684815.stgit@toke.dk

For some program types, the verifier relies on the expected_attach_type of
the program being verified in the verification process. However, for
freplace programs, the attach type was not propagated along with the
verifier ops, so the expected_attach_type would always be zero for freplace
programs.

This in turn caused the verifier to sometimes make the wrong call for
freplace programs. For all existing uses of expected_attach_type for this
purpose, the result of this was only false negatives (i.e., freplace
functions would be rejected by the verifier even though they were valid
programs for the target they were replacing). However, should a false
positive be introduced, this can lead to out-of-bounds accesses and/or
crashes.

The fix introduced in this patch is to propagate the expected_attach_type
to the freplace program during verification, and reset it after that is
done.

Fixes: be8704ff ("bpf: Introduce dynamic program extensions")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/158773526726.293902.13257293296560360508.stgit@toke.dk

Fix bug of not putting bpf_link in LINK_UPDATE command.
Also enforce zeroed old_prog_fd if no BPF_F_REPLACE flag is specified.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200424052045.4002963-1-andriin@fb.com