- 16 Jun, 2009 40 commits
-
-
tomas petr authored
"Leadtek WinFast DTV Dongle H" is a hybrid digital/analog USB-stick TV receiver. The code below allows the digital part to work with dvb_usb in linux. Signed-off-by:
tomas petr <tom-petr@seznam.cz> Signed-off-by:
Patrick Boettcher <pb@linuxtv.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Patrick Boettcher authored
This patch is reorganizing the frontend-attach mechanism in order to gain noise-less (superflous prints) deactivation of submodules. Credits go to Uwe Bugla for helping to clean and test the code. Signed-off-by:
Uwe Bugla <uwe.bugla@gmx.de> Signed-off-by:
-
Matthias Schwarzott authored
Reducing the print-levle of I2C error prints cleans some unwanted but unavoidable errors from default syslog-level. Signed-off-by:
Matthias Schwarzott <zzam@gentoo.org> Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Devin Heitmueller authored
The em28xx actually has a register that tells the driver what the maximum packet size is (based on a value programmed into the eeprom). Make use of that register instead of assuming a hardcoded value of 564 (since 564 is not correct for devices that do QAM such as the KWorld 340u). Note that for now the em2874 code isn't there, falling back to the 564 value, however this is not a problem since there are not any em2874 based devices in the current v4l-dvb tree). Thanks to Jarod Wilson for detecting the initial problem and figuring out that the isoc configuration was wrong for his device. Cc: Jarod Wilson <jarod@wilsonet.com> Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
-
Devin Heitmueller authored
Remove a debug printk() line I added which is no longer needed, and happened to be causing compile failures on some earlier kernels in Han's daily compile report. Signed-off-by:
-
Devin Heitmueller authored
According to the engineer at PCTV Systems, the xc5000 reset pin is supposed to be on GPIO12. However, despite three nights of effort, pulling that GPIO low didn't reset the xc5000. While pulling MO_SRST_IO low does reset the xc5000, this also resets in the s5h1409 being reset as well. This causes tuning to always fail since the internal state of the s5h1409 does not match the driver's state. Given that the only two conditions in which the driver performs a reset is during firmware load and powering down the chip, I am taking out the reset. We know that the chip is being reset when the cx88 comes online, and not being able to do power management for this board is better than not having any tuning at all. Problem discovered when implementing proper power management for the xc5000, which results in calls to the reset callback *after* s5h1409 is initialized. Cc: Steven Toth <stoth@kernellabs.com> Cc: Chaogui Zhang <czhang1974@gmail.com> Signed-off-by:
-
Devin Heitmueller authored
Add copyright line for xc5000.c. Cc: Steven Toth <stoth@kernellabs.com> Signed-off-by:
-
Devin Heitmueller authored
Make sure the au0828 issues the command to power down the tuner when the user is done using analog support. Signed-off-by:
-
Devin Heitmueller authored
Instead of polling at 100ms intervals for register writes, poll at 5ms intervals. This is consistent with the xc5000 specification, and improves tuning time by up to 500 ms on devices that such as the au0828 which do not properly implement i2c clock stretching (since the five register writes that occur for a tuning request often do not complete immediately but do complete far before 100ms has gone by). The net amount of time we wait before timing out is unchanged (500ms). Signed-off-by:
-
David T.L. Wong authored
This patch adds XC5000 supports for DVB-T 6MHz and 8MHz bandwidth. Signed-off-by:
David T.L. Wong <davidtlwong@gmail.com> Signed-off-by:
-
Devin Heitmueller authored
Xceive has graciously allowed us to now freely redistribute the xc5000 firmware, which eliminates the need for users to manually extract the blob from the Hauppauge driver. Thanks to Brian Mathews <bmathews@xceive.com> for providing this code Signed-off-by:
-
Devin Heitmueller authored
According to the xc5000 spec, the reset pin only needs to be held low for 10ms. Signed-off-by:
-
Devin Heitmueller authored
There was a typo in the module description for the "no_poweroff" option, where the help was being associated with the "debug" option instead. Signed-off-by:
-
Devin Heitmueller authored
Defer loading of the xc5000 firmware until it is actually needed. This helps on distros that have hald, which results in the device not being available for use for around ten seconds in cases where the i2c bus is slow (such as the HVR-950Q). Also, the firmware load isn't really useful since we immediately put the device to sleep afterward, which means a firmware reload will be required anyway. Signed-off-by:
-
Devin Heitmueller authored
Provide for the ability for a user to disable putting the tuner to sleep, in case he doesn't want to incur the cost of reloading the firmware when starting up his/her application. The module options are intentionally identical to xc3028. Signed-off-by:
-
Devin Heitmueller authored
Make it a little more obvious in the dmesg output what is going on during firmware upload. This is more important for boards like the HVR-950q that take nearly seven seconds to do the upload. Signed-off-by:
-
Devin Heitmueller authored
Starting in firmware version 1.1.44, Xceive recommends using the FINERFREQ for all normal tuning (the doc indicates reg 0x03 should only be used for fast scanning for channel lock) Signed-off-by:
-
Devin Heitmueller authored
Expose the firmware build number along with the other version info Signed-off-by:
-
Devin Heitmueller authored
The xc5000 datasheet indicates that the reset pin only needs to be held low for 10ms. Reduce the value accordingly, which speeds up the firmware load time a bit. Signed-off-by:
-
Devin Heitmueller authored
Xceive got rid of the XREG_POWER_DOWN register in later firmware revisions. Their technical support informed me that the correct way to put the tuner to sleep is to pull the reset pin (but don't reload the firmware). Signed-off-by:
-
Devin Heitmueller authored
This switches to a new version of the xc5000 firmware, extracted from the latest Hauppauge driver. It includes the support for the XREG_BUSY register (a lack of which was causing tuning to take 3200ms instead of around 300ms). Signed-off-by:
-
Devin Heitmueller authored
Don't sleep for 400ms polling the tuner's lock if in digital mode (since the xc5000 lock status registers appear to only be reliable in analog mode) Signed-off-by:
Devin Heitmueller <devin.heitmueller@gmail.com> Signed-off-by:
Michael Krufky <mkrufky@linuxtv.org> Signed-off-by:
-
Devin Heitmueller authored
Bring back the code that puts the xc5000 to sleep. For the Pinnacle 801e this results in power consumption at idle dropping from 325ma to 124ma. If there are *actually* any devices that don't work in this configuration, they should set dvb_frontend.ops.tuner_ops.sleep to NULL (per mkrufky's suggestion) Also, had to make sure we were making sure the firmware was loaded in the digital version of set_params, or else we end up get i2c errors if the device is asleep Signed-off-by:
-
Devin Heitmueller authored
Make return value checking for calls to i2c routines explicit. Signed-off-by:
-
Devin Heitmueller authored
Cleanup the i2c write routine, getting rid of a passthrough function with only one caller Signed-off-by:
-
Devin Heitmueller authored
This patch centralizes the i2c read functions, and eliminates pass-through function only called by one caller. Make reading of xc5000 registers an atomic i2c transaction in case we're on a multi-master bus. Signed-off-by:
-
Devin Heitmueller authored
Properly handle tuner reset failures (before it was always returning success) Signed-off-by:
-
Dmitri Belimov authored
Signed-off-by:
Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
Michael Krufky <mkrufky@kernellabs.com> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Steven Toth authored
The patch means the board will be recognised, and the parts brought out of reset correctly. This patches depends on the centralized GPIO patch to be merged. What's missing before the HVR-1270 will function for DTV? The model# needs to be added to avoid 'unknown model' output and the LG3305/Tuner need to be attached in cx23885-dvb.c Signed-off-by:
Steven Toth <stoth@kernellabs.com> Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
-
Steven Toth authored
The GPIO's on the product can be in one of three places. To date we've mainly used the GPIO's on the bridge itself, and once on the encoder. Rather than having the complexity of multiple GPIO writes/reads from isolated placed in the driver we'll route them through this function, so we can make intelligent decisions about 1) Where the GPIO lives and 2) Whether it conflicts (based on board) with some other function to avoid bugs. Signed-off-by:
-
Oliver Endriss authored
Some whitespace adjustments. Signed-off-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
