- 08 Jan, 2018 40 commits
-
-
Russell King authored
The mask argument for phy_modify() in several locations was inverted. Fixes: fea23fb5 ("net: phy: convert read-modify-write to phy_modify()") Reported-by:
Heiner Kallweit <hkallweit1@gmail.com> Tested-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Zhu Yanjun authored
Since both first_rx and rx_ring are the head of rx ring, it not necessary to use two structure members to statically indicate the head of rx ring. So first_rx is removed. CC: Srinivas Eeda <srinivas.eeda@oracle.com> CC: Joe Jin <joe.jin@oracle.com> CC: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by:
Zhu Yanjun <yanjun.zhu@oracle.com> Signed-off-by:
-
Stefano Brivio authored
The two conditions triggering BUG_ON() are somewhat unrelated: the tcp_skb_pcount() check is meant to catch TSO flaws, the second one checks sanity of congestion window bookkeeping. Split them into two separate BUG_ON() assertions on two lines, so that we know which one actually triggers, when they do. Signed-off-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
-
David Ahern authored
Allow a process bound to a VRF to connect to a linklocal address. Currently, this fails because of a mismatch between the scope of the linklocal address and the sk_bound_dev_if inherited by the VRF binding: $ ssh -6 fe80::70b8:cff:fedd:ead8%eth1 ssh: connect to host fe80::70b8:cff:fedd:ead8%eth1 port 22: Invalid argument Relax the scope check to allow the socket to be bound to the same L3 device as the scope id. This makes ipv6 linklocal consistent with other relaxed checks enabled by commits 1ff23bee ("net: l3mdev: Allow send on enslaved interface") and 7bb387c5 ("net: Allow IP_MULTICAST_IF to set index to L3 slave"). Signed-off-by:David Ahern <dsahern@gmail.com> Signed-off-by:
-
Sergei Shtylyov authored
Since the commit 888cc8c2 ("sh_eth: remove EDMAC_BIG_ENDIAN") (geez, I didn't realize that was 2 years ago!) the initializers in the SuperH platform code for the 'sh_eth_plat_data::edmac_endian' stopped to matter, so we can remove that field for good (not sure if it was ever useful -- SH7786 Ether has been reported to have the same EDMAC descriptor/register endiannes as configured for the SuperH CPU)... Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by:
-
David S. Miller authored
Peng Li says: ==================== add some new features and fix some bugs for HNS3 driver This patchset adds some new features support and fixes some bugs: [Patch 1/20] adds support to enable/disable vlan filter with ethtool [Patch 2/20] disables VFs change rxvlan offload status [Patch 3/20 - 13/120 fix bugs and refine some codes for packet statistics, support query with both ifconfig and ethtool. [Patch 14/20 - 20/20] fix some other bugs. ==================== Signed-off-by: -
Jian Shen authored
The statistics of rx/tx packets size greater than 1518 are not detailed. This patch adds more statistics for different packet size range. Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
-
Peng Li authored
There is a redundant semicolon, this patch removes it. Signed-off-by:
-
Fuyun Liang authored
Pause parameters include source address, transmit gap and pause time. The default value of the pause source address is zero in the hardware. Default pause parameters need to be set to the hardware. Also, when setting new mac address, the pause source address need to be updated. Fixes: 9dc2145d ("net: hns3: Add support for PFC setting in TM module") Signed-off-by:
Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by:
-
Fuyun Liang authored
When initializing the MAC, the MTU vlaue need to be set to the hardware too. Otherwise, the MTU value of software will be different from the MTU value of hardware. Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
-
Fuyun Liang authored
when changing MTU, The new MTU must need to be set to netdevice. Fixes: a8e8b7ff ("net: hns3: Add support to change MTU in HNS3 hardware") Signed-off-by:
-
Fuyun Liang authored
When setting MTU, actually what we do is configuring the max frame size for the hardware. ETH_HLEN、ETH_FCS_LEN and VLAN_HLEN must need to be considered. And the frame size which is less than the default value should not be set to the hardware. Because in the hardware, the the max frame size not only controls the RX packet size, but also controls the TX packet size. the RX packets whose size are greater than the setting value will be dropped. This patch fixes the bug setting a error max frame size to hardware. Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
-
Fuyun Liang authored
commit a9c782822166 ("net: hns3: add support for set_pauseparam") adds set_pauseparam support for ethtool cmd, but forgets to update fc_mode_last_time when PFC mode is disabled in hclge_cfg_pauseparam(). The wrong fc_mode_last_time will be used to update flow control mode when lldpad has been running. As a result, when using the ethtool command "-a", user will get a wrong pause parameter. This patch adds the fc_mode_last_time update when PFC mode is disabled. Fixes: a9c782822166 ("net: hns3: add support for set_pauseparam") Signed-off-by: -
Jian Shen authored
The result of tqp statistics query was read with an error position, fix it according to the user manual. Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
-
Jian Shen authored
Add packet statistics of netdev for ethtool -S, in order to show the statistics data for current net device. Remove update_stats() calling because it has been completed in hns3_get_netdev_stats(). Signed-off-by:
-
Jian Shen authored
The member "stats_size" of struct hns3_stats is useless, remove it and fix the macro definition which has uses this struct. Signed-off-by:
-
Jian Shen authored
The member "stats_offset" was designed to indicate the offset of each member of struct ring_stats in struct hns3_enet_ring, but forgot to add the offset of the member in struct ring_stats. Fixes: 496d03e9 ("net: hns3: Add Ethtool support to HNS3 driver") Signed-off-by:
-
Jian Shen authored
An error loop index was used while querying statistics data of tqps, which may cause call trace. Fixes: 496d03e9 ("net: hns3: Add Ethtool support to HNS3 driver") Signed-off-by:
-
Jian Shen authored
The dropped tx/rx packets number of each tqp should also be counted into the total drop tx/rx packets numbers. Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by:
-
Jian Shen authored
Update the HNS3_NIC_STATE_DOWN bit when NIC state changes. When NIC is down, mask the packet statistics for querying with ifconfig command. It's a common practice. Signed-off-by:
-
Jian Shen authored
It takes more than 200 query response messages between driver and IMP, while updating the packet statistics. It's too heavy for IMP to update it per second. Extend the update period of packet statistics data from 1 second to 300 seconds(if too long, the statistics may overflow). As a result, we need to update it while querying with ifconfig tool to keep the statistics data fresh. Signed-off-by:
-
Jian Shen authored
The igu_rx_err_pkt indicates the same error with mac_rx_fcs_err_pkt_num, so remove it. Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
-
Jian Shen authored
Fix spelling error "overrsize" --> "oversize". Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by:
-
Jian Shen authored
Some members of packet statistics are named in different styles. This patch unifies them with new internal name rules, the main modification are below: trans --> tx rcv --> rx rcb_q%d_tx --> txq#%d rcb_q%d_rx --> rxq#%d sw_err_cnt(tx side) --> tx_dropped sw_err_cnt(rx side) --> rx_dropped pkts --> packets tx_err_cnt --> errors rx_err_cnt --> errors Signed-off-by:
-
Jian Shen authored
Rxvlan offload status can only be changed by PF. Initialize the value of NETIF_F_HW_VLAN_CTAG_RX bit of hw_features for VFS to false, make sure user can't be able to change it. Signed-off-by:
-
Jian Shen authored
This patch adds vlan filter enable switch to support ethtool -K ethX rx-vlan-filter on/off. Signed-off-by:
-
David S. Miller authored
Subash Abhinov Kasiviswanathan says: ==================== net: qualcomm: rmnet: Enable csum offloads This series introduces the MAPv4 packet format for checksum offload plus some other minor changes. Patches 1-3 are cleanups. Patch 4 renames the ingress format to data format so that all data formats can be configured using this going forward. Patch 5 uses the pacing helper to improve TCP transmit performance. Patch 6-9 defines the the MAPv4 for checksum offload for RX and TX. A new header and trailer format are used as part of MAPv4. For RX checksum offload, only the 1's complement of the IP payload portion is computed by hardware. The meta data from RX header is used to verify the checksum field in the packet. Note that the IP packet and its field itself is not modified by hardware. This gives metadata to help with the RX checksum. For TX, the required metadata is filled up so hardware can compute the checksum. Patch 10 enables GSO on rmnet devices v1->v2: Fix sparse errors reported by kbuild test robot v2->v3: Update the commit message for Patch 5 based on Eric's comments ==================== Signed-off-by: -
Subash Abhinov Kasiviswanathan authored
Real devices may support scatter gather(SG), so enable SG on rmnet devices to use GSO. GSO reduces CPU cycles by 20% for a rate of 146Mpbs for a single stream TCP connection. Signed-off-by:
Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Signed-off-by:
-
Subash Abhinov Kasiviswanathan authored
TX checksum offload applies to TCP / UDP packets which are not fragmented using the MAPv4 checksum trailer. The following needs to be done to have checksum computed in hardware - 1. Set the checksum start offset and inset offset. 2. Set the csum_enabled bit 3. Compute and set 1's complement of partial checksum field in transport header. Signed-off-by:
-
Subash Abhinov Kasiviswanathan authored
When using the MAPv4 packet format in conjunction with MAP commands, a dummy DL checksum trailer will be appended to the packet. Before this packet is sent out as an ACK, the DL checksum trailer needs to be removed. Signed-off-by:
-
Subash Abhinov Kasiviswanathan authored
When using the MAPv4 packet format, receive checksum offload can be enabled in hardware. The checksum computation over pseudo header is not offloaded but the rest of the checksum computation over the payload is offloaded. This applies only for TCP / UDP packets which are not fragmented. rmnet validates the TCP/UDP checksum for the packet using the checksum from the checksum trailer added to the packet by hardware. The validation performed is as following - 1. Perform 1's complement over the checksum value from the trailer 2. Compute 1's complement checksum over IPv4 / IPv6 header and subtracts it from the value from step 1 3. Computes 1's complement checksum over IPv4 / IPv6 pseudo header and adds it to the value from step 2 4. Subtracts the checksum value from the TCP / UDP header from the value from step 3. 5. Compares the value from step 4 to the checksum value from the TCP / UDP header. 6. If the comparison in step 5 succeeds, CHECKSUM_UNNECESSARY is set and the packet is passed on to network stack. If there is a failure, then the packet is passed on as such without modifying the ip_summed field. The checksum field is also checked for UDP checksum 0 as per RFC 768 and for unexpected TCP checksum of 0. If checksum offload is disabled when using MAPv4 packet format in receive path, the packet is queued as is to network stack without the validations above. Signed-off-by:
-
Subash Abhinov Kasiviswanathan authored
The MAPv4 packet format adds support for RX / TX checksum offload. For a bi-directional UDP stream at a rate of 570 / 146 Mbps, roughly 10% CPU cycles are saved. For receive path, there is a checksum trailer appended to the end of the MAP packet. The valid field indicates if hardware has computed the checksum. csum_start_offset indicates the offset from the start of the IP header from which hardware has computed checksum. csum_length is the number of bytes over which the checksum was computed and the resulting value is csum_value. In the transmit path, a header is appended between the end of the MAP header and the start of the IP packet. csum_start_offset is the offset in bytes from which hardware will compute the checksum if the csum_enabled bit is set. udp_ip4_ind indicates if the checksum value of 0 is valid or not. csum_insert_offset is the offset from the csum_start_offset where hardware will insert the computed checksum. The use of this additional packet format for checksum offload is explained in subsequent patches. Signed-off-by:
-
Subash Abhinov Kasiviswanathan authored
The real device over which the rmnet devices are installed also aggregate multiple IP packets and sends them as a single large aggregate frame to the hardware. This causes degraded throughput for TCP TX due to bufferbloat. To overcome this problem, pacing shift value of 8 is set using the sk_pacing_shift_update() helper. This value was determined based on experiments with a single stream TCP TX using iperf for a duration of 30s. Pacing shift | Observed data rate (Mbps) 10 | 9 9 | 140 8 | 146 (Max link rate) Signed-off-by: -
Subash Abhinov Kasiviswanathan authored
This is done so that we can use this field for both ingress and egress flags. Signed-off-by:
-
Subash Abhinov Kasiviswanathan authored
rmnet_map_demultiplex() is only declared but not defined anywhere, so remove it. Signed-off-by:
-
Subash Abhinov Kasiviswanathan authored
rmnet devices cannot have a mux id of 255. This is validated when assigning the mux id to the rmnet devices. As a result, checking for mux id 255 does not apply in egress path. Signed-off-by:
-
Subash Abhinov Kasiviswanathan authored
We already check the headroom once in rmnet_map_egress_handler(), so this is not needed. Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== ipv6: Align nexthop behaviour with IPv4 This set tries to eliminate some differences between IPv4's and IPv6's treatment of nexthops. These differences are most likely a side effect of IPv6's data structures (specifically 'rt6_info') that incorporate both the route and the nexthop and the late addition of ECMP support in commit 51ebd318 ("ipv6: add support of equal cost multipath (ECMP)"). IPv4 and IPv6 do not react the same to certain netdev events. For example, upon carrier change affected IPv4 nexthops are marked using the RTNH_F_LINKDOWN flag and the nexthop group is rebalanced accordingly. IPv6 on the other hand, does nothing which forces us to perform a carrier check during route lookup and dump. This makes it difficult to introduce features such as non-equal-cost multipath that are built on top of this set [1]. In addition, when a netdev is put administratively down IPv4 nexthops are marked using the RTNH_F_DEAD flag, whereas IPv6 simply flushes all the routes using these nexthops. To be consistent with IPv4, multipath routes should only be flushed when all nexthops in the group are considered dead. The first 12 patches introduce non-functional changes that store the RTNH_F_DEAD and RTNH_F_LINKDOWN flags in IPv6 routes based on netdev events, in a similar fashion to IPv4. This allows us to remove the carrier check performed during route lookup and dump. The next three patches make sure we only flush a multipath route when all of its nexthops are dead. Last three patches add test cases for IPv4/IPv6 FIB. These verify that both address families react similarly to netdev events. Finally, this series also serves as a good first step towards David Ahern's goal of treating nexthops as standalone objects [2], as it makes the code more in line with IPv4 where the nexthop and the nexthop group are separate objects from the route itself. 1. https://github.com/idosch/linux/tree/ipv6-nexthops 2. http://vger.kernel.org/netconf2017_files/nexthop-objects.pdf Changes since RFC (feedback from David Ahern): * Remove redundant declaration of rt6_ifdown() in patch 4 and adjust comment referencing it accordingly * Drop patch to flush multipath routes upon NETDEV_UNREGISTER. Reword cover letter accordingly * Use a temporary variable to make code more readable in patch 15 ==================== Signed-off-by:
-
Ido Schimmel authored
Check that IPv4 and IPv6 react the same when the carrier of a netdev is toggled. Local routes should not be affected by this, whereas unicast routes should. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Acked-by:
-
Ido Schimmel authored
Check that IPv4 and IPv6 react the same when a netdev is being put administratively down. Signed-off-by:
-
