Saeed Mahameed says:

====================
Support Mellanox BlueField SmartNIC (mlx5-updates-2019-02-15)

Bodong Wang says,

BlueField device is a multi-core ARM processor in a highly integrated
system on chip coupled with the ConnectX interconnect controller.
BlueField device can be presented in one out of two modes:

- SEPARATED_HOST: ARM processors as a separated and orthogonal host
  like any other external host in the multi-host virtualization model.
- EMBEDDED_CPU: ARM processors as Embedded CPU (EC) and part of the
  external hosts virtualization model.

While existing driver already supports the device on separated_host
mode, this patch series focus on the functionalities of embedded_cpu
mode.

On embedded_cpu mode, BlueField device exposes regular network
controller PCI function in the BlueField host(e.g, x86). However, a
separate PCI function called Embedded CPU Physical Function(ECPF) is
also added to the ARM host side, where standard Linux distributions is
able to run on the ARM cores. Depends on the NV configuration from
firmware, ECPF can be the e-switch manager and firmware pages supplier.
If ECPF is configured as e-switch manager and page supplier, it will
take over the responsibilities from the PF on BlueField host includes:
- Owns, controls and manages all e-switch parts, and takes e-switch
  traffic by default. It also should perform ENABLE_HCA for the host
  PF just like a PF does for its VFs.
- Provides and manages the ICM host memory required for the HCA to
  store various contexts for itself, the PF and VFs belong the
  e-switch it manages.

The PF on BlueField host side is still responsible for:
- Control its own permanent MAC.
- PCI and SRIOV configurations and perform ENABLE_HCA for its VFs.

The ECPF can also retrieve information about the external host it
controls, like host identifier, PCI BDF and number of virtual functions.
As these parameters may be changed dynamically, an event will be triggered
to the driver on ECPF side.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2019-02-15

please apply a few more qeth patches to net-next. Along with some smaller
improvements, this revamps our code for the SW statistics that are exposed
through ETHTOOL_GSTATS.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than special-casing OSN in a number of places, just give this
device type its own netdev_ops structure.

When setting up the OSN net_device, also skip the handling of the
various HW offloads (eg TSO). The device shouldn't be advertising any of
them, and the OSN code paths in qeth don't have support for them.
In particular RX VLAN filtering is not supported, so don't hook up those
callbacks in the netdev_ops.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement a trivial callback that exposes the queue sizes.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accumulate per-TX queue statistics, and increase their size to 64 bit.
Don't bother with enabling/disabling the statistics, the overhead is
negligible.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most of this is self-contained code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Counting the number of function calls and the time spent in functions
is best left to proper tracing facilities.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qeth dynamically allocates an array for storing pointers to its
Output Queue structures. Switch this to a static array - we are
currently limited to 4 Output Queues, so shrinking the qeth_qdio_info
struct by just a few bytes doesn't justify the additional complexity.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Once a qeth ccwgroup device is set online, it's also armed for internal
recovery. So allow for testing that code path via sysfs, regardless of
whether the interface is up or down.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For the forwarding selftests to work, we need network namespaces when
using veth/vrf otherwise ping/ping6 commands like these:

ip vrf exec vveth0 /bin/ping 192.0.2.2 -c 10 -i 0.1 -w 5

will fail because network namespaces may not be enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rt6_cache_allowed_for_pmtu() checks for rt->from presence, but
it does not access the RCU protected pointer. We can use
rcu_access_pointer() and clean-up the code a bit. No functional
changes intended.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in several dev_err messages, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, the e-switch driver requires going to legacy mode before
changing to the offloads mode. This makes sense for regular case as
the legacy mode is done by creating VFs.

However, it's problematic when ECPF is the eswitch manager. In such
case, ECPF will control the vports on peer host including the peer
PF and VFs. But ECPF doesn't need and shall not create VFs as the
VFs are created in the peer PF host.

Grant ECPF the ability to change from none to the offloads mode. Note
that currently the only way to go back to none mode is by unloading
the ECPF driver.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When host PF changes the number of VFs, the ECPF esw driver will get
a FW event. It should query the number of VFs enabled by host PF and
update the VF reps accordingly. Note that host PF can't change the
number of VFs dynamically, it has to reset the number of VFs to 0
before changing to a new positive number.

The host event is registered when driver is moving to switchdev mode,
and it's the last step to do in esw_offloads_init. It's unregistered
and the work queue is flushed when driver quits from switchdev mode.
In this way, the host event and devlink command are serialized.

When driver is enabling switchdev mode, pay attention to the following
two facts:
1. Host PF must not have VF initialized as the flow table in ECPF has
   ENCAP enabled as default. Such flow table can't be created with
   existing initialized VFs.
2. ECPF doesn't know how many VFs the host PF will enable, ECPF
   offloads flow steering shall create the flow table/groups based on
   the max number of VFs possibly supported by host PF.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

ECPF connects to the eswitch through vport 0xfffe. ECPF may or may
not be the eswitch manager depending on firmware configuration.

1. If ECPF is eswitch manager: ECPF will take over the eswitch manager
   responsibility. A rep of the host PF shall be created at the ECPF
   side for the eswitch manager to control.

2. If ECPF is not eswitch manager: host PF will be the eswitch manager,
   ECPF acts similar as a VF to the host PF. Host PF will be aware
   of the ECPF vport presence and control it's rep.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In offloads mode, the current implementation puts the uplink
representor at index zero of the vport reps array. It is not "natural"
to place it at index 0 since we want to put the representor for vport
0 at index 0 with the introduction of SmartNIC. A separate patch will
handle the case whether a rep is needed for vport 0 (PF vport).

So, we want to have a different placeholder for uplink vport and
representor. It was placed at the end of vport and rep array. Since
vport number can no longer act as an index into the vport or
representors arrays, use functions to map vport numbers to indices
when accessing the vports or representors arrays, and vice versa.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Eswitch has two users: IB and ETH. They both register repersentors
when mlx5 interface is added, and unregister the repersentors when
mlx5 interface is removed. Ideally, each driver should only deal with
the entities which are unique to itself. However, current IB and ETH
drivers have to perform the following eswitch operations:

1. When registering, specify how many vports to register. This number
   is the same for both drivers which is the total available vport
   numbers.
2. When unregistering, specify the number of registered vports to do
   unregister. Also, unload the repersentors which are already loaded.

It's unnecessary for eswitch driver to hands out the control of above
operations to individual driver users, as they're not unique to each
driver. Instead, such operations should be centralized to eswitch
driver. This consolidates eswitch control flow, and simplified IB and
ETH driver.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently the driver loads and unloads all reps in an unbreakable
group. However, with ECPF, the reps of special vports such as uplink
and host PF should always be loaded in switchdev mode where the reps
for VFs will be loaded on-demand and unloaded on no-demand. This is
a pre-step for that change.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently the eswitch vport reps have a valid indicator, which is
set on register and unset on unregister. However, a rep can be loaded
or not loaded when doing unregister, current driver checks if the
vport of that rep is enabled as a flag to imply the rep is loaded.
However, for ECPF, this is not valid as the host PF will enable the
vports for its VFs instead.

Add three states: {unregistered, registered, loaded}, with the
following state changes across different operations:

	create: (none)       -> unregistered
	reg:    unregistered -> registered
	load:   registered   -> loaded
	unload: loaded       -> registered
	unreg:  registered   -> unregistered

Note that the state shall only be updated inside eswitch driver rather
than individual drivers such as ETH or IB.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Suggested-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

With only PF and VF, it is sufficient to have the vport/rep array
index as the vport number. This is because PF and VF vports numbers
are consecutive serial numbers. In downstream patches with
introducing of ECPF and UPLINK vports, it's not consecutive any more.

Use getter to get specific vport/rep, and use iterator to traversal
a list of vport/rep. This hides the translation between array index
and vport number, and provides flexibility of using different
translation mechanism in the future.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When driver is entering offloads mode, there are two major tasks to
do: initialize flow steering and create representors. Flow steering
should make sure enough flow table/group spaces are reserved for all
reps. Representors will be created in a group, all or none.

With the introduction of ECPF, flow steering should still reserve the
same spaces. But, the representors are not always loaded/unloaded in a
single piece. Once ECPF is in offloads mode, it will get the number
of VF changing event from host PF. In such scenario, only the VF reps
should be loaded/unloaded, not the reps for special vports (such as
the uplink vport).

Thus, when entering offloads mode, driver should specify the total
number of reps, and the number of VF reps separately. When leaving
offloads mode, the cleanup should use the information self-contained
in eswitch such as number of VFs.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

E-switch offloads mode initialize/cleanup multiple steering related
entities (flow table/group). Refactor these operations to internal
helper functions for better block design.

This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Commands referring to vports use the following scheme:

1. When referring to my own vport, put 0 in vport and 0 in other_vport.
2. When referring to another vport, put the vport number of the
   referred vport and put 1 in other_vport. It was assumed that driver
   is accessing other vport when vport number is greater than 0.

With the above scheme, the case that ECPF eswitch manager is trying
to access host PF vport will fall over with scheme 1 as the vport
number is 0. This is apparently wrong as driver is trying to refer
other vport.

As such usage can only happen in the eswitch context, change relevant
functions to provide other vport input properly.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In SmartNIC mode, the eswitch manager is not necessarily the PF
(vport 0). Use a helper function to get the correct eswitch manager
vport number and cache on the eswitch instance for fast reference.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When bonding is added, driver assumes that it's RoCE LAG if no VF is
enabled. This is not enough for ECPF as the VF is enabled in host PF
side. LAG should only choose RoCE mode when both slave devices meet
conditions below:
 1. E-Switch offloads mode is NONE.
 2. No VF is enabled.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Merge mlx5-next shared branched into net-next,

From Bodong Wang:
1) Introduction of ECPF (Embedded CPU Physical Function), and low level
bits for mlx5 SmartNic capabilities support.
2) Vport enumeration refactoring that affect mlx5_ib and mlx5_core

From Aya Levin,
3) Add support for 50Gbps per lane link modes in the Port Type and Speed
register (PTYS)
4) Refactor low level query functions for PTYS register
5) Add support for 50Gbps per lane link modes to mlx5_ib

Note: due to a change in API in mlx5/core and a later patch from net-next,
a fixup was squashed with this merge commit that replaces FDB_UPLINK_VPORT
with MLX5_VPORT_UPLINK which exists only in upstream net-next.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The netfilter conflicts were rather simple overlapping
changes.

However, the cls_tcindex.c stuff was a bit more complex.

On the 'net' side, Cong is fixing several races and memory
leaks.  Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.

What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU.  I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull block fixes from Jens Axboe:

 - Ensure we insert into the hctx dispatch list, if a request is marked
   as DONTPREP (Jianchao)

 - NVMe pull request, single missing unlock on error fix (Keith)

 - MD pull request, single fix for a potentially data corrupting issue
   (Nate)

 - Floppy check_events regression fix (Yufen)

* tag 'for-linus-20190215' of git://git.kernel.dk/linux-block:
  md/raid1: don't clear bitmap bits on interrupted recovery.
  floppy: check_events callback should not return a negative number
  nvme-pci: add missing unlock for reset error
  blk-mq: insert rq with DONTPREP to hctx dispatch list when requeue

Merge tag 'for-5.0/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix bug in DM crypt's sizing of its block integrity tag space,
   resulting in less memory use when DM crypt layers on DM integrity.

 - Fix a long-standing DM thinp crash consistency bug that was due to
   improper handling of FUA. This issue is specific to writes that fill
   an entire thinp block which needs to be allocated.

* tag 'for-5.0/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm thin: fix bug where bio that overwrites thin block ignores FUA
  dm crypt: don't overallocate the integrity tag space

Pull MMC fixes from Ulf Hansson:
 "A couple of MMC fixes intended for v5.0-rc7.

  MMC core:
   - Fix deadlock bug for block I/O requests

  MMC host:
   - sunxi: Disable broken HS-DDR mode for H5 by default
   - sunxi: Avoid unsupported speed modes declared via DT
   - meson-gx: Restore interrupt name"

* tag 'mmc-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: meson-gx: fix interrupt name
  mmc: block: handle complete_work on separate workqueue
  mmc: sunxi: Filter out unsupported modes declared in the device tree
  mmc: sunxi: Disable HS-DDR mode for H5 eMMC controller by default

Pull drm fixes from Dave Airlie:
 "Usual pull request, little larger than I'd like but nothing too
  strange in it. Willy found an bug in the lease ioctl calculations, but
  it's a drm master only ioctl which makes it harder to mess with.

 i915:
   - combo phy programming fix
   - opregion version check fix for VBT RVDA lookup
   - gem mmap ioctl race fix
   - fbdev hpd during suspend fix
   - array size bounds check fix in pmu

  amdgpu:
   - Vega20 psp fix
   - Add vrr range to debugfs for freesync debugging

  sched:
   - Scheduler race fix

  vkms:
   - license header fixups

  imx:
   - Fix CSI register offsets for i.MX51 and i.MX53.
   - Fix delayed page flip completion events on i.MX6QP due to
     unexpected behaviour of the PRE when issuing NOP buffer updates to
     the same buffer address.
   - Stop throwing errors for plane updates on disabled CRTCs when a
     userspace process is killed while a plane update is pending.
   - Add missing of_node_put cleanup in imx_ldb_bind"

* tag 'drm-fixes-2019-02-15-1' of git://anongit.freedesktop.org/drm/drm:
  drm: Use array_size() when creating lease
  drm/amdgpu/psp11: TA firmware is optional (v3)
  drm/i915/opregion: rvda is relative from opregion base in opregion 2.1+
  drm/i915/opregion: fix version check
  drm/i915: Prevent a race during I915_GEM_MMAP ioctl with WC set
  drm/i915: Block fbdev HPD processing during suspend
  drm/i915/pmu: Fix enable count array size and bounds checking
  drm/i915/cnl: Fix CNL macros for Voltage Swing programming
  drm/i915/icl: combo port vswing programming changes per BSPEC
  drm/vkms: Fix license inconsistent
  drm/amd/display: Expose connector VRR range via debugfs
  drm/sched: Always trace the dependencies we wait on, to fix a race.
  gpu: ipu-v3: pre: don't trigger update if buffer address doesn't change
  gpu: ipu-v3: Fix CSI offsets for imx53
  drm/imx: imx-ldb: add missing of_node_puts
  gpu: ipu-v3: Fix i.MX51 CSI control registers offset
  drm/imx: ignore plane updates on disabled crtcs

Pull crypto fix from Herbert Xu:
 "This fixes a crash on resume in the ccree driver"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ccree - fix resume race condition on init

Pull networking fixes from David Miller:

 1) Fix MAC address setting in mac80211 pmsr code, from Johannes Berg.

 2) Probe SFP modules after being attached, from Russell King.

 3) Byte ordering bug in SMC rx_curs_confirmed code, from Ursula Braun.

 4) Revert some r8169 changes that are causing regressions, from Heiner
    Kallweit.

 5) Fix spurious connection timeouts in netfilter nat code, from Florian
    Westphal.

 6) SKB leak in tipc, from Hoang Le.

 7) Short packet checkum issue in mlx4, similar to a previous mlx5
    change, from Saeed Mahameed. The issue is that whilst padding bytes
    are usually zero, it is not guarateed and the hardware doesn't take
    the padding bytes into consideration when generating the checksum.

 8) Fix various races in cls_tcindex, from Cong Wang.

 9) Need to set stream ext to NULL before freeing in SCTP code, from Xin
    Long.

10) Fix locking in phy_is_started, from Heiner Kallweit.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
  net: ethernet: freescale: set FEC ethtool regs version
  net: hns: Fix object reference leaks in hns_dsaf_roce_reset()
  mm: page_alloc: fix ref bias in page_frag_alloc() for 1-byte allocs
  net: phy: fix potential race in the phylib state machine
  net: phy: don't use locking in phy_is_started
  selftests: fix timestamping Makefile
  net: dsa: bcm_sf2: potential array overflow in bcm_sf2_sw_suspend()
  net: fix possible overflow in __sk_mem_raise_allocated()
  dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit
  net: phy: fix interrupt handling in non-started states
  sctp: set stream ext to NULL after freeing it in sctp_stream_outq_migrate
  sctp: call gso_reset_checksum when computing checksum in sctp_gso_segment
  net/mlx5e: XDP, fix redirect resources availability check
  net/mlx5: Fix a compilation warning in events.c
  net/mlx5: No command allowed when command interface is not ready
  net/mlx5e: Fix NULL pointer derefernce in set channels error flow
  netfilter: nft_compat: use-after-free when deleting targets
  team: avoid complex list operations in team_nl_cmd_options_set()
  net_sched: fix two more memory leaks in cls_tcindex
  net_sched: fix a memory leak in cls_tcindex
  ...

Pull signal fix from Eric Biederman:
 "Just a single patch that restores PTRACE_EVENT_EXIT functionality that
  was accidentally broken by last weeks fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  signal: Restore the stop PTRACE_EVENT_EXIT

Passing an object_count of sufficient size will make
object_count * 4 wrap around to be very small, then a later function
will happily iterate off the end of the object_ids array.  Using
array_size() will saturate at SIZE_MAX, the kmalloc() will fail and
we'll return an -ENOMEM to the norty userspace.

Fixes: 62884cd3 ("drm: Add four ioctls for managing drm mode object leases [v7]")
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Dave Airlie <airlied@redhat.com>

amdgpu:
- Vega20 psp fix
- Add vrr range to debugfs for freesync debugging

sched:
- Scheduler race fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190213202958.3336-1-alexander.deucher@amd.com

Merge tag 'drm-intel-fixes-2019-02-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

drm/i915 fixes for v5.0-rc7:
- combo phy programming fix
- opregion version check fix for VBT RVDA lookup
- gem mmap ioctl race fix
- fbdev hpd during suspend fix
- array size bounds check fix in pmu
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/877ee3504b.fsf@intel.com

drm-misc-fixes for v5.0:
- Fix license inconsistency in vkms.
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/812e2f53-d72a-8fba-6c8c-fde8f44cf141@linux.intel.com

When provisioning a new data block for a virtual block, either because
the block was previously unallocated or because we are breaking sharing,
if the whole block of data is being overwritten the bio that triggered
the provisioning is issued immediately, skipping copying or zeroing of
the data block.

When this bio completes the new mapping is inserted in to the pool's
metadata by process_prepared_mapping(), where the bio completion is
signaled to the upper layers.

This completion is signaled without first committing the metadata.  If
the bio in question has the REQ_FUA flag set and the system crashes
right after its completion and before the next metadata commit, then the
write is lost despite the REQ_FUA flag requiring that I/O completion for
this request must only be signaled after the data has been committed to
non-volatile storage.

Fix this by deferring the completion of overwrite bios, with the REQ_FUA
flag set, until after the metadata has been committed.

Cc: stable@vger.kernel.org
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

This reverts commit 8099b047.

It turns out that people do actually depend on the shebang string being
truncated, and on the fact that an interpreter (like perl) will often
just re-interpret it entirely to get the full argument list.
Reported-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>