- 15 Mar, 2016 16 commits
-
-
Yaniv Gardi authored
This change enables the device ref clock before changing to HS mode and disables it if entered to PWM mode. Reviewed-by:
Gilad Broner <gbroner@codeaurora.org> Signed-off-by:
Yaniv Gardi <ygardi@codeaurora.org> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Yaniv Gardi authored
Some UFS devices (and may be host) have issues if LCC is enabled. So we are setting PA_Local_TX_LCC_Enable to 0 before link startup which will make sure that both host and device TX LCC are disabled once link startup is completed. Reviewed-by:
-
Yaniv Gardi authored
We put the UFS device in sleep state & UFS link in hibern8 state during runtime suspend. After this we put all the UFS rails in low power modes immediately but it seems some devices may still draw more than sleep current from UFS rails (especially from VCCQ rail) at-least for 500us. To avoid this situation, this change adds 2ms delay before putting these UFS rails in LPM mode. Reviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
-
Yaniv Gardi authored
Currently when we try to put the link in off/disabled state during suspend, it seems link is not being kept in low power mode. This patch fixes the issue by putting the link in hibern8 first (so device also puts the link in low power mode) and then stop the host controller. Reviewed-by:
-
Yaniv Gardi authored
Optimal values of local UniPro parameters like PA_Hibern8Time & PA_TActivate can help reduce the hibern8 exit latency. If both host and device supports UniPro ver1.6 or later, these parameters will be automatically tuned during link startup itself. But if either host or device doesn't support UniPro ver 1.6 or later, we have to manually tune them. But to keep manual tuning logic simple, we will only do manual tuning if local unipro version doesn't support ver1.6 or later. Reviewed-by:
-
Yaniv Gardi authored
We are seeing that some devices are raising the urgent bkops exception events even when BKOPS status doesn't indicate performace impacted or critical. Handle these device by determining their urgent bkops status at runtime. Reviewed-by:
-
Yaniv Gardi authored
Query commands have 100ms timeout and it may timeout if they are issued in parallel to ongoing read/write SCSI commands, this change adds the retry (max: 10) in case command timeouts. Reviewed-by:
-
Yaniv Gardi authored
Some vendor's UFS device sends back to back NACs for the DL data frames causing the host controller to raise the DFES error status. Sometimes such UFS devices send back to back NAC without waiting for new retransmitted DL frame from the host and in such cases it might be possible the Host UniPro goes into bad state without raising the DFES error interrupt. If this happens then all the pending commands would timeout only after respective SW command (which is generally too large). This change workarounds such device behaviour like this: - As soon as SW sees the DL NAC error, it would schedule the error handler - Error handler would sleep for 50ms to see if there any fatal errors raised by UFS controller. - If there are fatal errors then SW does normal error recovery. - If there are no fatal errors then SW sends the NOP command to device to check if link is alive. - If NOP command times out, SW does normal error recovery - If NOP command succeed, skip the error handling. If DL NAC error is seen multiple times with some vendor's UFS devices then enable this quirk to initiate quick error recovery and also silence related error logs to reduce spamming of kernel logs. Reviewed-by: -
Yaniv Gardi authored
UFS driver's error handler forcefully tries to clear all the pending requests. For each pending request in the queue, it waits 1 sec for it to get cleared. If we have multiple requests in the queue then it's possible that we might end up waiting for those many seconds before resetting the host. But note that resetting host would any way clear all the pending requests from the hardware. Hence this change skips the forceful clear of the pending requests if we are anyway going to reset the host (for fatal errors). Reviewed-by:
-
Yaniv Gardi authored
Some UFS devices don't require VCCQ rail for device operations hence this change adds support to recognize such devices and remove vote for the unused VCCQ rail. Reviewed-by:
-
Yaniv Gardi authored
Currently we use the host quirks mechanism in order to handle both device and host controller quirks. In order to support various of UFS devices we should separate handling the device quirks from the host controller's. Reviewed-by:
Raviv Shvili <rshvili@codeaurora.org> Signed-off-by:
-
Yaniv Gardi authored
This change adds support to read device descriptor and string descriptor from a UFS device Reviewed-by:
Hannes Reinecke <hare@suse.com> Signed-off-by:
-
Yaniv Gardi authored
Sometimes due to hw issues it takes some time to the host controller register to update. In order to verify the register has updated, a polling is done until its value is set. In addition the functions ufshcd_hba_stop() and ufshcd_wait_for_register() was updated with an additional input parameter, indicating the timeout between reads will be done by sleeping or spinning the cpu. Reviewed-by:
-
Yaniv Gardi authored
A race condition exists between request requeueing and scsi layer error handling: When UFS driver queuecommand returns a busy status for a request, it will be requeued and its tag will be freed and set to -1. At the same time it is possible that the request will timeout and scsi layer will start error handling for it. The scsi layer reuses the request and its tag to send error related commands to the device, however its tag is no longer valid. As this request was never really sent to the device, there is no point to start error handling with the device. Implement the scsi error handling timeout callback and bypass SCSI error handling for request that were not actually sent to the device. For such requests simply reset the block layer timer. Otherwise, let SCSI layer perform the usual error handling. Reviewed-by:
-
Yaniv Gardi authored
When control reaches to Linux UFS driver during UFS boot mode, UFS host controller interrupt status/enable registers may have left over settings. In order to avoid any spurious interrupts due to these left overs, it's important to clear these interrupt status/enable registers before enabling UFS interrupt handling. Reviewed-by:
-
Yaniv Gardi authored
Different platform may have different number of lanes for the UFS link. Add parameter to device tree specifying how many lanes should be configured for the UFS link. Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
- 14 Mar, 2016 4 commits
-
-
Douglas Gilbert authored
One of the strange things that the original sg driver did was let the user provide both a data-out buffer (it followed the sg_header+cdb) _and_ specify a reply length greater than zero. What happened was that the user data-out buffer was copied into some kernel buffers and then the mid level was told a read type operation would take place with the data from the device overwriting the same kernel buffers. The user would then read those kernel buffers back into the user space. From what I can tell, the above action was broken by commit fad7f01e ("sg: set dxferp to NULL for READ with the older SG interface") in 2008 and syzkaller found that out recently. Make sure that a user space pointer is passed through when data follows the sg_header structure and command. Fix the abnormal case when a non-zero reply_len is also given. Fixes: fad7f01e Cc: <stable@vger.kernel.org> #v2.6.28+ Signed-off-by:
Douglas Gilbert <dgilbert@interlog.com> Reviewed-by:
Ewan Milne <emilne@redhat.com> Signed-off-by:
-
Vitaly Kuznetsov authored
Commit 3209f9d7 ("scsi: storvsc: Fix a bug in the handling of SRB status flags") filtered SRB_STATUS_AUTOSENSE_VALID out effectively making the (SRB_STATUS_ABORTED | SRB_STATUS_AUTOSENSE_VALID) case a dead code. The logic from this branch (e.g. storvsc_device_scan() call) is still required, fix the check. Cc: <stable@vger.kernel.org> #v4.4+ Fixes: 3209f9d7 ("scsi: storvsc: Fix a bug in the handling of SRB status flags") Signed-off-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Acked-by:
K. Y. Srinivasan <kys@microsoft.com> Signed-off-by:
-
Maurizio Lombardi authored
In beiscsi_setup_boot_info(), the boot_kset pointer should be set to NULL in case of failure otherwise an invalid pointer dereference may occur later. Cc: <stable@vger.kernel.org> Signed-off-by:
Maurizio Lombardi <mlombard@redhat.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
Jitendra Bhivare <jitendra.bhivare@broadcom.com> Signed-off-by:
-
Martin K. Petersen authored
Commit 39773722 ("sd: Make discard granularity match logical block size when LBPRZ=1") accidentally set the granularity to one byte instead of one logical block on devices that provide deterministic zeroes after UNMAP. Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Reviewed-by:
Bart Van Assche <bart.vanassche@sandisk.com> Fixes: 39773722 Cc: <stable@vger.kernel.org> #v4.4+
-
- 11 Mar, 2016 2 commits
-
-
Hannes Reinecke authored
The test for the existence vpd_pg83 is inverted. Fixes: 7e47976b ("scsi_sysfs: add 'is_bin_visible' callback") Signed-off-by:
-
Sumit Saxena authored
There are few MFI adapters which do not support MR_DCMD_PD_LIST_QUERY so if MFI adapters fail this DCMD, it should not be considered as FATAL and driver should not issue kill adapter and set per controller's instance variable- pd_list_not_supported so that same variable can be used inside functions- slave_alloc and slave_configure to allow firmware scan. Killing adapter because of DCMD failure when this DCMD is not supported causes driver's probe getting failed. This issue got introduced by commit 6d40afbc ("megaraid_sas: MFI IO timeout handling"). Killing adapter in case of this DCMD failure should be limited to Fusion adapters only. Per controller's instance variable allow_fw_scan is removed as pd_list_not_supported better reflect the purpose. Fixes: 6d40afbcSigned-off-by:
Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
-
- 10 Mar, 2016 1 commit
-
-
Lars-Peter Clausen authored
Calling synchronize_irq() right before free_irq() is quite useless. On one hand the IRQ can easily fire again before free_irq() is entered, on the other hand free_irq() itself calls synchronize_irq() internally (in a race condition free way), before any state associated with the IRQ is freed. Patch was generated using the following semantic patch: // <smpl> @@ expression irq; @@ -synchronize_irq(irq); free_irq(irq, ...); // </smpl> Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Acked-by:
Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by:
-
- 09 Mar, 2016 7 commits
-
-
Manoj N. Kumar authored
With the current value of cmd_per_lun at 16, the throughput over a single adapter is limited to around 150kIOPS. Increase the value of cmd_per_lun to 256 to improve throughput. With this change a single adapter is able to attain close to the maximum throughput (380kIOPS). Also change the number of RRQ entries that can be queued. Signed-off-by:
Manoj N. Kumar <manoj@linux.vnet.ibm.com> Acked-by:
Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Reviewed-by:
Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by:
-
Manoj N. Kumar authored
When switching to the internal LUN defined on the IBM CXL flash adapter, there is an unnecessary scan occurring on the second port. This scan leads to the following extra lines in the log: Dec 17 10:09:00 tul83p1 kernel: [ 3708.561134] cxlflash 0008:00:00.0: cxlflash_queuecommand: (scp=c0000000fc1f0f00) 11/1/0/0 cdb=(A0000000-00000000-10000000-00000000) Dec 17 10:09:00 tul83p1 kernel: [ 3708.561147] process_cmd_err: cmd failed afu_rc=32 scsi_rc=0 fc_rc=0 afu_extra=0xE, scsi_extra=0x0, fc_extra=0x0 By definition, both of the internal LUNs are on the first port/channel. When the lun_mode is switched to internal LUN the same value for host->max_channel is retained. This causes an unnecessary scan over the second port/channel. This fix alters the host->max_channel to 0 (1 port), if internal LUNs are configured and switches it back to 1 (2 ports) while going back to external LUNs. Signed-off-by:
-
Uma Krishnan authored
In order to support cxlflash in the PowerVM environment, underlying hypervisor APIs have imposed a kernel API ordering change. For the superpipe access to LUN, user applications need a context. The cxlflash module creates this context by making a sequence of cxl calls. In the current code, a context is initialized via cxl_dev_context_init() followed by cxl_process_element(), a function that obtains the process element id. Finally, cxl_start_work() is called to attach the process element. In the PowerVM environment, a process element id cannot be obtained from the hypervisor until the process element is attached. The cxlflash module is unable to create contexts without a valid process element id. To fix this problem, cxl_start_work() is called before obtaining the process element id. Signed-off-by:
-
Matthew R. Ochs authored
The cxlflash_disk_attach() routine currently uses a cascading error gate strategy for its error cleanup path. While this strategy is commonly used to handle cleanup scenarios, it is too restrictive when function callouts need to be restructured. Problems range from inserting error path bugs in previously 'good' code to the cleanup path imposing design changes to how the normal path is structured. A less restrictive approach is needed to support ordering changes that come about when operating in different environments. To overcome this restriction, the error cleanup path is modified to have a single entrypoint and use conditional logic to cleanup where necessary. Entities that require multiple cleanup steps must be carefully vetted to ensure their APIs support state. In cases where they do not (none as of this commit) additional local variables can be used to maintain state on their behalf. Signed-off-by:
-
Matthew R. Ochs authored
Presently, context information structures are allocated and initialized in the same routine, create_context(). This imposes an ordering restriction such that all pieces of information needed to initialize a context must be known before the context is even allocated. This design point is not flexible when the order of context creation needs to be modified. Specifically, this can lead to problems when members of the context information structure are a part of an ordering dependency (i.e. - the 'work' structure embedded within the context). To remedy, the allocation is left as-is, inside of the existing create_context() routine and the initialization is transitioned to a new void routine, init_context(). At the same time, in anticipation of these routines not being called in sequence, a state boolean is added to the context information structure to track when the context has been initilized. The context teardown routine, destroy_context(), is modified to support being called with a non-initialized context. Signed-off-by:
-
Uma Krishnan authored
When operating in the PowerVM environment, the cxlflash module can receive an error from the hypervisor indicating that there are existing mappings in the page table for the process MMIO space. This issue exists because term_afu() currently invokes term_mc() before stop_afu(), allowing for the master context to be detached first and the problem state area to be unmapped second. To resolve this issue, stop_afu() should be called before term_mc(). Signed-off-by:
-
Manoj N. Kumar authored
The calls to pci_request_regions(), pci_resource_start(), pci_set_dma_mask(), pci_set_master() and pci_save_state() are all unnecessary for the IBM CXL flash adapter since data buffers are not required to be mapped to the device's memory. The use of services such as pci_set_dma_mask() are problematic on hypervisor managed systems as the IBM CXL flash adapter is operating under a virtual PCI Host Bridge (virtual PHB) which does not support these services. cxlflash 0001:00:00.0: init_pci: Failed to set PCI DMA mask rc=-5 The resolution is to simplify init_pci(), to a point where it does the bare minimum (pci_enable_device). Similarly, remove the call the pci_release_regions() from cxlflash_remove(). Signed-off-by:
-
- 08 Mar, 2016 1 commit
-
-
Lars-Peter Clausen authored
Calling synchronize_irq() right before free_irq() is quite useless. On one hand the IRQ can easily fire again before free_irq() is entered, on the other hand free_irq() itself calls synchronize_irq() internally (in a race condition free way), before any state associated with the IRQ is freed. Patch was generated using the following semantic patch: // <smpl> @@ expression irq; @@ -synchronize_irq(irq); free_irq(irq, ...); // </smpl> Signed-off-by:
-
- 05 Mar, 2016 9 commits
-
-
Hannes Reinecke authored
'device_add' will be evaluating the 'is_visible' callback when creating the sysfs attributes. As by this time the device handler has not been attached the 'access_state' attribute will never be visible. This patch moves the code around so that the device handler is present by the time 'is_visible' is evaluated to correctly display the 'access_state' attribute. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
-
Hannes Reinecke authored
Update the 'access_state' field of the SCSI device whenever the path state changes. Signed-off-by:
-
Hannes Reinecke authored
Track attached SCSI devices and update the 'access_state' whenever the path state of the device changes. Signed-off-by:
-
Hannes Reinecke authored
Track attached SCSI devices and update the 'access_state' field whenever an ALUA state change has been detected. Signed-off-by:
-
Hannes Reinecke authored
scsi_proto.h now contains definitions for the ALUA state, so we don't have to carry them in the device handler. Signed-off-by:
-
Hannes Reinecke authored
Add an 'access_state' field to struct scsi_device and display them in sysfs as 'access_state' and 'preferred_path' attribute. Signed-off-by:
-
Hannes Reinecke authored
Add 'is_bin_visible' callback to blank out unsupported vpd pages. Reviewed-by:
Shane Seymour <shane.seymour@hpe.com> Reviewed-by:
-
Arnd Bergmann authored
The mvumi scsi hides the references to its suspend/resume functions in an #ifdef but does not hide the implementation the same way: drivers/scsi/mvumi.c:2632:12: error: 'mvumi_suspend' defined but not used [-Werror=unused-function] drivers/scsi/mvumi.c:2651:12: error: 'mvumi_resume' defined but not used [-Werror=unused-function] This adds __maybe_unused annotations so the compiler knows it can silently drop them instead of warning, while avoiding the addition of another #ifdef. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Reviewed-by:
-
K. Y. Srinivasan authored
tree: https://na01.safelinks.protection.outlook.com/?url=https%3a%2f%2fgit.kernel.org%2fpub%2fscm%2flinux%2fkernel%2fgit%2ftorvalds%2flinux.git&data=01%7c01%7ckys%40microsoft.com%7ce2e0622715844b79ad7108d32796ec3c%7c72f988bf86f141af91ab2d7cd011db47%7c1&sdata=ubr4GbBaNS%2ftOz%2buJBk0CL9N0UNG9x2TidLgy6Yovg4%3d master head: 03c21cb7 commit: dac58241 storvsc: Properly support Fibre Channel devices date: 3 weeks ago config: x86_64-randconfig-s3-01281016 (attached as .config) reproduce: git checkout dac58241 # save the attached .config to linux build tree make ARCH=x86_64 All errors (new ones prefixed by >>): drivers/built-in.o: In function `storvsc_remove': >> storvsc_drv.c:(.text+0x213af7): undefined reference to `fc_remove_host' drivers/built-in.o: In function `storvsc_drv_init': >> storvsc_drv.c:(.init.text+0xcbcc): undefined reference to `fc_attach_transport' >> storvsc_drv.c:(.init.text+0xcc06): undefined reference to `fc_release_transport' drivers/built-in.o: In function `storvsc_drv_exit': >> storvsc_drv.c:(.exit.text+0x123c): undefined reference to `fc_release_transport' With this commit, the storvsc driver depends on FC atttributes. Make this dependency explicit. Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
-
