WoWLAN is supported in RS9113 device through GPIO pin2.
wowlan config frame is internally sent to firmware in mac80211
suspend handler. Also beacon miss threshold and keep-alive time
values are increased to avoid un-necessary disconnection with AP.
Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Driver is transmitting in 11N rates, when connected to an AP in
TKIP security mode. Add a check to disable_11n to fix the issue.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When joining an IBSS network, wdev->ssid/_len will already be
set, so there's no need to write them. In any case, they are
internal cfg80211 values, and have very little user-visible
impact.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath.git patches for 4.15. Major changes:

ath10k

* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
  there it's supported (QCA99x0 and QCA4019)

Since mac80211 maintains the sequence number for each STA/TID,
driver doesn't need to maintain a copy.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In _rtl8821ae_dbi_write(), wrtie_addr should be write_addr.
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Commit 66cc0442 ("bcma: use bcma_debug and pr_cont in MIPS driver")
converted a printk(KERN_DEBUG to bcma_debug.

bcma_debug is guarded by a #define DEBUG via pr_debug.

This means that the bcma_debug will generally not be emitted
but any pr_cont following the bcma_debug will be emitted.

Correct this by removing the uses of pr_cont by using a temporary.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In the previous commit I left the indentation alone to help reviewing
the patch, this one now runs the three new functions through 'indent -kr -8'
with some manual fixups to avoid silliness.

No changes other than whitespace are intended here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The stack consumption in this driver is still relatively high, with one
remaining warning if the warning level is lowered to 1536 bytes:

drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_n.c:17135:1: error: the frame size of 1880 bytes is larger than 1536 bytes [-Werror=frame-larger-than=]

The affected function is actually a collection of three separate implementations,
and each of them is fairly large by itself. Splitting them up is done easily
and improves readability at the same time.

I'm leaving the original indentation to make the review easier.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrew Zaborowski <andrew.zaborowski@intel.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrew Zaborowski <andrew.zaborowski@intel.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Cc: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Cc: Karun Eagalapati <karun256@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Solomon Peachy <pizza@shaftnet.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Igor Mitsyanko <imitsyanko@quantenna.com>
Cc: Avinash Patil <avinashp@quantenna.com>
Cc: Sergey Matyukevich <smatyukevich@quantenna.com>
Cc: Kamlesh Rath <krath@quantenna.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2017-10-18' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Second batch of iwlwifi patches for 4.15

* Allocate reorder buffer dynamically to save memory;
* Fix a FW dump problem in the A000 family;
* Fix for a statistics gathering issue (v2);
* Sort the list of 9000 devices to make it easier to find entries;
* A couple of cleanups in the FW dump code;
* Remove some unnecessary variables and fields and calculations;

syzkaller got crashes at dismantle time [1]

It is not correct to test (tun->flags & IFF_NAPI) in tun_napi_disable()
and tun_napi_del() : Each tun_file can have different mode, depending
on how they were created.

Similarly I have changed tun_get_user() and tun_poll_controller()
to use the new tfile->napi_enabled boolean.

[  154.331360] BUG: unable to handle kernel NULL pointer dereference at           (null)
[  154.339220] IP: [<ffffffff9634cad6>] hrtimer_active+0x26/0x60
[  154.344983] PGD 0
[  154.347009] Oops: 0000 [#1] SMP
[  154.350680] gsmi: Log Shutdown Reason 0x03
[  154.379572] task: ffff994719150dc0 ti: ffff99475c0ae000 task.ti: ffff99475c0ae000
[  154.387043] RIP: 0010:[<ffffffff9634cad6>]  [<ffffffff9634cad6>] hrtimer_active+0x26/0x60
[  154.395232] RSP: 0018:ffff99475c0afce8  EFLAGS: 00010246
[  154.400542] RAX: ffff994754850ac0 RBX: ffff994753e65408 RCX: ffff994753e65388
[  154.407666] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff994753e65408
[  154.414790] RBP: ffff99475c0afce8 R08: 0000000000000000 R09: 0000000000000000
[  154.421921] R10: ffff99475f6f5910 R11: 0000000000000001 R12: 0000000000000000
[  154.429044] R13: ffff99417deab668 R14: ffff99417deaa780 R15: ffff99475f45dde0
[  154.436174] FS:  0000000000000000(0000) GS:ffff994767a00000(0000) knlGS:0000000000000000
[  154.444249] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  154.449986] CR2: 0000000000000000 CR3: 00000005a8a0e000 CR4: 0000000000022670
[  154.457110] Stack:
[  154.459120]  ffff99475c0afd28 ffffffff9634d614 1000000000000000 0000000000000000
[  154.466598]  ffffe54240000000 ffff994753e65408 ffff994753e653a8 ffff99417deab668
[  154.474067]  ffff99475c0afd48 ffffffff9634d6fd ffff99474c2be678 ffff994753e65398
[  154.481537] Call Trace:
[  154.483985]  [<ffffffff9634d614>] hrtimer_try_to_cancel+0x24/0xf0
[  154.490074]  [<ffffffff9634d6fd>] hrtimer_cancel+0x1d/0x30
[  154.495563]  [<ffffffff96860b3c>] napi_disable+0x3c/0x70
[  154.500875]  [<ffffffff9678ae62>] __tun_detach+0xd2/0x360
[  154.506272]  [<ffffffff9678b117>] tun_chr_close+0x27/0x40
[  154.511669]  [<ffffffff9646ebe6>] __fput+0xd6/0x1e0
[  154.516548]  [<ffffffff9646ed3e>] ____fput+0xe/0x10
[  154.521429]  [<ffffffff963035a2>] task_work_run+0x72/0x90
[  154.526827]  [<ffffffff962e9407>] do_exit+0x317/0xb60
[  154.531879]  [<ffffffff962e9c8f>] do_group_exit+0x3f/0xa0
[  154.537275]  [<ffffffff962e9d07>] SyS_exit_group+0x17/0x20
[  154.542769]  [<ffffffff969784be>] entry_SYSCALL_64_fastpath+0x12/0x17

Fixes: 94317099 ("net-tun: enable NAPI for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All of the notifier data (fib_info, tos, type and table id) are
contained in the fib_alias. Pass it to the notifier instead of
each data separately shortening the argument list by 3.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

New socket option TCP_FASTOPEN_KEY to allow different keys per
listener.  The listener by default uses the global key until the
socket option is set.  The key is a 16 bytes long binary data. This
option has no effect on regular non-listener TCP sockets.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
mlxsw: spectrum_router: Add extack messages for RIF and VRF overflow

Currently, exceeding the number of VRF instances or the number of router
interfaces either fails with a non-intuitive EBUSY:
    $ ip li set swp1s1.6 vrf vrf-1s1-6 up
    RTNETLINK answers: Device or resource busy

or fails silently (IPv6) since the checks are done in a work queue. This
set adds support for the address validator notifier to spectrum which
allows ext-ack based messages to be returned on failure.

To make that happen the IPv6 version needs to be converted from atomic
to blocking (patch 2), and then support for extack needs to be added
to the notifier (patch 3). Patch 1 reworks the locking in ipv6_add_addr
to work better in the atomic and non-atomic code paths. Patches 4 and 5
add the validator notifier to spectrum and then plumb the extack argument
through spectrum_router.

With this set, VRF overflows fail with:
   $ ip li set swp1s1.6 vrf vrf-1s1-6 up
   Error: spectrum: Exceeded number of supported VRF.

and RIF overflows fail with:
   $ ip addr add dev swp1s2.191 10.12.191.1/24
   Error: spectrum: Exceeded number of supported router interfaces.

v2 -> v3
- fix surround context of patch 4 which was altered by c30f5d01

v1 -> v2
- fix error path in ipv6_add_addr: reset rt to NULL (Ido comment) and
  add in6_dev_put on ifa once the hold has been done

RFC -> v1
- addressed various comments from Ido
- refactored ipv6_add_addr to allow ifa's to be allocated with
  GFP_KERNEL as requested by DaveM
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add extack argument down to mlxsw_sp_rif_create and mlxsw_sp_vr_create
to set an error message on RIF or VR overflow. Now on overflow of
either resource the user gets an informative message as opposed to
failing with EBUSY.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for inetaddr_validator and inet6addr_validator. The
notifiers provide a means for validating ipv4 and ipv6 addresses
before the addresses are installed and on failure the error
is propagated back to the user.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add extack to in_validator_info and in6_validator_info. Update the one
user of each, ipvlan, to return an error message for failures.

Only manual configuration of an address is plumbed in the IPv6 code path.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

inet6addr_validator chain was added by commit 3ad7d246 ("Ipvlan
should return an error when an address is already in use") to allow
address validation before changes are committed and to be able to
fail the address change with an error back to the user. The address
validation is not done for addresses received from router
advertisements.

Handling RAs in softirq context is the only reason for the notifier
chain to be atomic versus blocking. Since the only current user, ipvlan,
of the validator chain ignores softirq context, the notifier can be made
blocking and simply not invoked for softirq path.

The blocking option is needed by spectrum for example to validate
resources for an adding an address to an interface.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6_add_addr is called in process context with rtnl lock held
(e.g., manual config of an address) or during softirq processing
(e.g., autoconf and address from a router advertisement).

Currently, ipv6_add_addr calls rcu_read_lock_bh shortly after entry
and does not call unlock until exit, minus the call around the address
validator notifier. Similarly, addrconf_hash_lock is taken after the
validator notifier and held until exit. This forces the allocation of
inet6_ifaddr to always be atomic.

Refactor ipv6_add_addr as follows:
1. add an input boolean to discriminate the call path (process context
   or softirq). This new flag controls whether the alloc can be done
   with GFP_KERNEL or GFP_ATOMIC.

2. Move the rcu_read_lock_bh and unlock calls only around functions that
   do rcu updates.

3. Remove the in6_dev_hold and put added by 3ad7d246 ("Ipvlan should
   return an error when an address is already in use."). This was done
   presumably because rcu_read_unlock_bh needs to be called before calling
   the validator. Since rcu_read_lock is not needed before the validator
   runs revert the hold and put added by 3ad7d246 and only do the
   hold when setting ifp->idev.

4. move duplicate address check and insertion of new address in the global
   address hash into a helper. The helper is called after an ifa is
   allocated and filled in.

This allows the ifa for manually configured addresses to be done with
GFP_KERNEL and reduces the overall amount of time with rcu_read_lock held
and hash table spinlock held.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/net: updates 2017-10-18

please apply some additional robustness fixes and cleanups for 4.15.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A few lines down, qeth_prepare_control_data() makes further changes to
the control cmd buffer, and then also writes a trace entry for it.
So the first entry just pollutes the trace file with intermediate data,
drop it.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch to napi_complete_done(), and thus enable delayed GRO flushing.
The timeout is configured via /sys/class/net/<if>/gro_flush_timeout.

Default timeout is 0, so no change in behaviour.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current code bails out when two subsequent buffer elements hold
insufficient data to contain a qeth_hdr packet descriptor.
This seems reasonable, but it would be legal for quirky hardware to
leave a few elements empty and then present packets in a subsequent
element. These packets would currently be dropped.

So make sure to check all buffer elements, until we hit the LAST_ENTRY
indication.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the allocation of SG skbs into the main path. This allows for
a little code sharing, and handling ENOMEM from within one place.

As side effect, L2 SG skbs now get the proper amount of additional
headroom (read: zero) instead of the hard-coded ETH_HLEN.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the open-coded skb_add_rx_frag(), and use a fall-through
to remove some duplicated code.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of silently discarding VLAN registration requests on OSM,
just indicate that this card type doesn't support VLAN.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's no reason why l2_set_mac_address() should ever be called for
a netdevice that's not owned by qeth. It's certainly not required for
VLAN devices, which have their own netdev_ops.

Also:
1) we don't do such validation for any of the other netdev_ops routines.
2) the code in question clearly has never been actually exercised;
   it's broken. After determining that the device is not owned
   by qeth, it would still use dev->ml_priv to write a qeth trace entry.

Remove the check, and its helper that walked the global card list.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Drop the support for Token Ring,
2. use the ETH_DATA_LEN macro for the default L2 MTU,
3. handle OSM via the default case (as OSM is L2-only), and
4. document why the L3 MTU is reduced.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the allocation of the addr buffer fails, we need to free
our refcount on the inetdevice before returning.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sysfs enabled value is a boolean, so kstrtobool() is a better fit
for parsing the input string since it does the range checking for us.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With commit "s390/ccwgroup: tie a ccwgroup driver to its ccw driver",
the ccwgroup core now ensures that a qeth group device only consists of
ccw devices which are supported by qeth. Therefore remove qeth's
internal device matching, and use .driver_info to determine the card
type.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>