[ Upstream commit f06b7549 ]

Lennert reported a failure to add different mpls encaps in a multipath
route:

  $ ip -6 route add 1234::/16 \
        nexthop encap mpls 10 via fe80::1 dev ens3 \
        nexthop encap mpls 20 via fe80::1 dev ens3
  RTNETLINK answers: File exists

The problem is that the duplicate nexthop detection does not compare
lwtunnel configuration. Add it.

Fixes: 19e42e45 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reported-by: João Taveira Araújo <joao.taveira@gmail.com>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 05a6b4ca ]

The code that detects a failed soft reset of Octeon is comparing the wrong
value against the reset value of the Octeon SLI_SCRATCH_1 register,
resulting in an inability to detect a soft reset failure.  Fix it by using
the correct value in the comparison, which is any non-zero value.

Fixes: f21fb3ed ("Add support of Cavium Liquidio ethernet adapters")
Fixes: c0eab5b3 ("liquidio: CN23XX firmware download")
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9af9959e ]

commit 9256645a ("net/core: relax BUILD_BUG_ON in
netdev_stats_to_stats64") made an attempt to read beyond
the size of the source a possibility.

Fix to only copy src size to dest. As dest might be bigger than src.

 ==================================================================
 BUG: KASAN: slab-out-of-bounds in netdev_stats_to_stats64+0xe/0x30 at addr ffff8801be248b20
 Read of size 192 by task VBoxNetAdpCtl/6734
 CPU: 1 PID: 6734 Comm: VBoxNetAdpCtl Tainted: G           O    4.11.4prahal+intel+ #118
 Hardware name: LENOVO 20CDCTO1WW/20CDCTO1WW, BIOS GQET52WW (1.32 ) 05/04/2017
 Call Trace:
  dump_stack+0x63/0x86
  kasan_object_err+0x1c/0x70
  kasan_report+0x270/0x520
  ? netdev_stats_to_stats64+0xe/0x30
  ? sched_clock_cpu+0x1b/0x190
  ? __module_address+0x3e/0x3b0
  ? unwind_next_frame+0x1ea/0xb00
  check_memory_region+0x13c/0x1a0
  memcpy+0x23/0x50
  netdev_stats_to_stats64+0xe/0x30
  dev_get_stats+0x1b9/0x230
  rtnl_fill_stats+0x44/0xc00
  ? nla_put+0xc6/0x130
  rtnl_fill_ifinfo+0xe9e/0x3700
  ? rtnl_fill_vfinfo+0xde0/0xde0
  ? sched_clock+0x9/0x10
  ? sched_clock+0x9/0x10
  ? sched_clock_local+0x120/0x130
  ? __module_address+0x3e/0x3b0
  ? unwind_next_frame+0x1ea/0xb00
  ? sched_clock+0x9/0x10
  ? sched_clock+0x9/0x10
  ? sched_clock_cpu+0x1b/0x190
  ? VBoxNetAdpLinuxIOCtlUnlocked+0x14b/0x280 [vboxnetadp]
  ? depot_save_stack+0x1d8/0x4a0
  ? depot_save_stack+0x34f/0x4a0
  ? depot_save_stack+0x34f/0x4a0
  ? save_stack+0xb1/0xd0
  ? save_stack_trace+0x16/0x20
  ? save_stack+0x46/0xd0
  ? kasan_slab_alloc+0x12/0x20
  ? __kmalloc_node_track_caller+0x10d/0x350
  ? __kmalloc_reserve.isra.36+0x2c/0xc0
  ? __alloc_skb+0xd0/0x560
  ? rtmsg_ifinfo_build_skb+0x61/0x120
  ? rtmsg_ifinfo.part.25+0x16/0xb0
  ? rtmsg_ifinfo+0x47/0x70
  ? register_netdev+0x15/0x30
  ? vboxNetAdpOsCreate+0xc0/0x1c0 [vboxnetadp]
  ? vboxNetAdpCreate+0x210/0x400 [vboxnetadp]
  ? VBoxNetAdpLinuxIOCtlUnlocked+0x14b/0x280 [vboxnetadp]
  ? do_vfs_ioctl+0x17f/0xff0
  ? SyS_ioctl+0x74/0x80
  ? do_syscall_64+0x182/0x390
  ? __alloc_skb+0xd0/0x560
  ? __alloc_skb+0xd0/0x560
  ? save_stack_trace+0x16/0x20
  ? init_object+0x64/0xa0
  ? ___slab_alloc+0x1ae/0x5c0
  ? ___slab_alloc+0x1ae/0x5c0
  ? __alloc_skb+0xd0/0x560
  ? sched_clock+0x9/0x10
  ? kasan_unpoison_shadow+0x35/0x50
  ? kasan_kmalloc+0xad/0xe0
  ? __kmalloc_node_track_caller+0x246/0x350
  ? __alloc_skb+0xd0/0x560
  ? kasan_unpoison_shadow+0x35/0x50
  ? memset+0x31/0x40
  ? __alloc_skb+0x31f/0x560
  ? napi_consume_skb+0x320/0x320
  ? br_get_link_af_size_filtered+0xb7/0x120 [bridge]
  ? if_nlmsg_size+0x440/0x630
  rtmsg_ifinfo_build_skb+0x83/0x120
  rtmsg_ifinfo.part.25+0x16/0xb0
  rtmsg_ifinfo+0x47/0x70
  register_netdevice+0xa2b/0xe50
  ? __kmalloc+0x171/0x2d0
  ? netdev_change_features+0x80/0x80
  register_netdev+0x15/0x30
  vboxNetAdpOsCreate+0xc0/0x1c0 [vboxnetadp]
  vboxNetAdpCreate+0x210/0x400 [vboxnetadp]
  ? vboxNetAdpComposeMACAddress+0x1d0/0x1d0 [vboxnetadp]
  ? kasan_check_write+0x14/0x20
  VBoxNetAdpLinuxIOCtlUnlocked+0x14b/0x280 [vboxnetadp]
  ? VBoxNetAdpLinuxOpen+0x20/0x20 [vboxnetadp]
  ? lock_acquire+0x11c/0x270
  ? __audit_syscall_entry+0x2fb/0x660
  do_vfs_ioctl+0x17f/0xff0
  ? __audit_syscall_entry+0x2fb/0x660
  ? ioctl_preallocate+0x1d0/0x1d0
  ? __audit_syscall_entry+0x2fb/0x660
  ? kmem_cache_free+0xb2/0x250
  ? syscall_trace_enter+0x537/0xd00
  ? exit_to_usermode_loop+0x100/0x100
  SyS_ioctl+0x74/0x80
  ? do_sys_open+0x350/0x350
  ? do_vfs_ioctl+0xff0/0xff0
  do_syscall_64+0x182/0x390
  entry_SYSCALL64_slow_path+0x25/0x25
 RIP: 0033:0x7f7e39a1ae07
 RSP: 002b:00007ffc6f04c6d8 EFLAGS: 00000206 ORIG_RAX: 0000000000000010
 RAX: ffffffffffffffda RBX: 00007ffc6f04c730 RCX: 00007f7e39a1ae07
 RDX: 00007ffc6f04c730 RSI: 00000000c0207601 RDI: 0000000000000007
 RBP: 00007ffc6f04c700 R08: 00007ffc6f04c780 R09: 0000000000000008
 R10: 0000000000000541 R11: 0000000000000206 R12: 0000000000000007
 R13: 00000000c0207601 R14: 00007ffc6f04c730 R15: 0000000000000012
 Object at ffff8801be248008, in cache kmalloc-4096 size: 4096
 Allocated:
 PID = 6734
  save_stack_trace+0x16/0x20
  save_stack+0x46/0xd0
  kasan_kmalloc+0xad/0xe0
  __kmalloc+0x171/0x2d0
  alloc_netdev_mqs+0x8a7/0xbe0
  vboxNetAdpOsCreate+0x65/0x1c0 [vboxnetadp]
  vboxNetAdpCreate+0x210/0x400 [vboxnetadp]
  VBoxNetAdpLinuxIOCtlUnlocked+0x14b/0x280 [vboxnetadp]
  do_vfs_ioctl+0x17f/0xff0
  SyS_ioctl+0x74/0x80
  do_syscall_64+0x182/0x390
  return_from_SYSCALL_64+0x0/0x6a
 Freed:
 PID = 5600
  save_stack_trace+0x16/0x20
  save_stack+0x46/0xd0
  kasan_slab_free+0x73/0xc0
  kfree+0xe4/0x220
  kvfree+0x25/0x30
  single_release+0x74/0xb0
  __fput+0x265/0x6b0
  ____fput+0x9/0x10
  task_work_run+0xd5/0x150
  exit_to_usermode_loop+0xe2/0x100
  do_syscall_64+0x26c/0x390
  return_from_SYSCALL_64+0x0/0x6a
 Memory state around the buggy address:
  ffff8801be248a80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
  ffff8801be248b00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 >ffff8801be248b80: 00 00 00 00 00 00 00 00 00 00 00 07 fc fc fc fc
                                                     ^
  ffff8801be248c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
  ffff8801be248c80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ==================================================================
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4b4c21fa ]

It's not a good idea to add the same hlist_node to two different hash lists.
This leads to various hard to debug memory corruptions.

Fixes: 8ed66f0e ("geneve: implement support for IPv6-based tunnels")
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 69e76661 ]

It's not a good idea to add the same hlist_node to two different hash lists.
This leads to various hard to debug memory corruptions.

Fixes: b1be00a6 ("vxlan: support both IPv4 and IPv6 sockets in a single vxlan device")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ec8add2a ]

Currently, when the link for $DEV is down, this command succeeds but the
address is removed immediately by DAD (1):

    ip addr add 1111::12/64 dev $DEV valid_lft 3600 preferred_lft 1800

In the same situation, this will succeed and not remove the address (2):

    ip addr add 1111::12/64 dev $DEV
    ip addr change 1111::12/64 dev $DEV valid_lft 3600 preferred_lft 1800

The comment in addrconf_dad_begin() when !IF_READY makes it look like
this is the intended behavior, but doesn't explain why:

     * If the device is not ready:
     * - keep it tentative if it is a permanent address.
     * - otherwise, kill it.

We clearly cannot prevent userspace from doing (2), but we can make (1)
work consistently with (2).

addrconf_dad_stop() is only called in two cases: if DAD failed, or to
skip DAD when the link is down. In that second case, the fix is to avoid
deleting the address, like we already do for permanent addresses.

Fixes: 3c21edbd ("[IPV6]: Defer IPv6 device initialization until the link becomes ready.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8ff93de7 ]

Symbol error during carrier counter from PPCNT was mistakenly reported as
TX carrier errors in get_stats ndo, although it's an RX counter.

Fixes: 269e6b3a ("net/mlx5e: Report additional error statistics in get stats ndo")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2a0165a0 ]

Draining the health workqueue will ignore future health works including
the one that report hardware failure and thus we can't enter error state
Instead cancel the recovery flow and make sure only recovery flow won't
be scheduled.

Fixes: 5e44fca5 ('net/mlx5: Only cancel recovery work when cleaning up device')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8ce59b16 ]

When wait for firmware init fails, previous code would mistakenly
return success and cause inconsistency in the driver state.

Fixes: 6c780a02 ("net/mlx5: Wait for FW readiness before initializing command interface")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f7a320ff upstream.

This problem was found by strace ioctl list generator.

Fixes: 15c6098c ("staging: android: ion: Remove ion_handle and ion_client")
Signed-off-by: Gleb Fotengauer-Malinovskiy <glebfm@altlinux.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 99c13b8c upstream.

The pat_enabled() logic is broken on CPUs which do not support PAT and
where the initialization code fails to call pat_init(). Due to that the
enabled flag stays true and pat_enabled() returns true wrongfully.

As a consequence the mappings, e.g. for Xorg, are set up with the wrong
caching mode and the required MTRR setups are omitted.

To cure this the following changes are required:

  1) Make pat_enabled() return true only if PAT initialization was
     invoked and successful.

  2) Invoke init_cache_modes() unconditionally in setup_arch() and
     remove the extra callsites in pat_disable() and the pat disabled
     code path in pat_init().

Also rename __pat_enabled to pat_disabled to reflect the real purpose of
this variable.

Fixes: 9cd25aac ("x86/mm/pat: Emulate PAT when it is disabled")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bernhard Held <berny156@gmx.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@suse.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1707041749300.3456@file01.intranet.prod.int.rdu2.redhat.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1ea1516f upstream.

kstrtoull returns 0 on success, however, in reserved_clusters_store we
will return -EINVAL if kstrtoull returns 0, it makes us fail to update
reserved_clusters value through sysfs.

Fixes: 76d33bcaSigned-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fec17cb2 upstream.

Otherwise, we enable all sorts of forgeries via timing attack.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Suggested-by: Stephan Müller <smueller@chronox.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 42cfcafb upstream.

Changes in the SW cts (ciphertext stealing) code in
commit 0605c41c ("crypto: cts - Convert to skcipher")
revealed a problem in the CAAM driver:
when cts(cbc(aes)) is executed and cts runs in SW,
cbc(aes) is offloaded in CAAM; cts encrypts the last block
in atomic context and CAAM incorrectly decides to use GFP_KERNEL
for memory allocation.

Fix this by allowing GFP_KERNEL (sleeping) only when MAY_SLEEP flag is
set, i.e. remove MAY_BACKLOG flag.

We split the fix in two parts - first is sent to -stable, while the
second is not (since there is no known failure case).

Link: http://lkml.kernel.org/g/20170602122446.2427-1-david@sigma-star.atReported-by: David Gstir <david@sigma-star.at>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a9332e9a upstream.

There is a clean-up bug in the core comedi module initialization
functions, `comedi_init()`.  If the `comedi_num_legacy_minors` module
parameter is non-zero (and valid), it creates that many "legacy" devices
and registers them in SysFS.  A failure causes the function to clean up
and return an error.  Unfortunately, it fails to destroy the "comedi"
class that was created earlier.  Fix it by adding a call to
`class_destroy(comedi_class)` at the appropriate place in the clean-up
sequence.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dc32190f upstream.

The key table is not intialized correctly without this call.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a0c4acd2 upstream.

If a writer could been woken up, the above branch

	if (sem->count == 0)
		break;

would have moved us to taking the sem. So, it's
not the time to wake a writer now, and only readers
are allowed now. Thus, 0 must be passed to __rwsem_do_wake().

Next, __rwsem_do_wake() wakes readers unconditionally.
But we mustn't do that if the sem is owned by writer
in the moment. Otherwise, writer and reader own the sem
the same time, which leads to memory corruption in
callers.

rwsem-xadd.c does not need that, as:

  1) the similar check is made lockless there,
  2) in __rwsem_mark_wake::try_reader_grant we test,

that sem is not owned by writer.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 17fcbd59 "locking/rwsem: Fix down_write_killable() for CONFIG_RWSEM_GENERIC_SPINLOCK=y"
Link: http://lkml.kernel.org/r/149762063282.19811.9129615532201147826.stgit@localhost.localdomainSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2fd1d2c4 upstream.

Andrei Vagin writes:
FYI: This bug has been reproduced on 4.11.7
> BUG: Dentry ffff895a3dd01240{i=4e7c09a,n=lo}  still in use (1) [unmount of proc proc]
> ------------[ cut here ]------------
> WARNING: CPU: 1 PID: 13588 at fs/dcache.c:1445 umount_check+0x6e/0x80
> CPU: 1 PID: 13588 Comm: kworker/1:1 Not tainted 4.11.7-200.fc25.x86_64 #1
> Hardware name: CompuLab sbc-flt1/fitlet, BIOS SBCFLT_0.08.04 06/27/2015
> Workqueue: events proc_cleanup_work
> Call Trace:
>  dump_stack+0x63/0x86
>  __warn+0xcb/0xf0
>  warn_slowpath_null+0x1d/0x20
>  umount_check+0x6e/0x80
>  d_walk+0xc6/0x270
>  ? dentry_free+0x80/0x80
>  do_one_tree+0x26/0x40
>  shrink_dcache_for_umount+0x2d/0x90
>  generic_shutdown_super+0x1f/0xf0
>  kill_anon_super+0x12/0x20
>  proc_kill_sb+0x40/0x50
>  deactivate_locked_super+0x43/0x70
>  deactivate_super+0x5a/0x60
>  cleanup_mnt+0x3f/0x90
>  mntput_no_expire+0x13b/0x190
>  kern_unmount+0x3e/0x50
>  pid_ns_release_proc+0x15/0x20
>  proc_cleanup_work+0x15/0x20
>  process_one_work+0x197/0x450
>  worker_thread+0x4e/0x4a0
>  kthread+0x109/0x140
>  ? process_one_work+0x450/0x450
>  ? kthread_park+0x90/0x90
>  ret_from_fork+0x2c/0x40
> ---[ end trace e1c109611e5d0b41 ]---
> VFS: Busy inodes after unmount of proc. Self-destruct in 5 seconds.  Have a nice day...
> BUG: unable to handle kernel NULL pointer dereference at           (null)
> IP: _raw_spin_lock+0xc/0x30
> PGD 0

Fix this by taking a reference to the super block in proc_sys_prune_dcache.

The superblock reference is the core of the fix however the sysctl_inodes
list is converted to a hlist so that hlist_del_init_rcu may be used.  This
allows proc_sys_prune_dache to remove inodes the sysctl_inodes list, while
not causing problems for proc_sys_evict_inode when if it later choses to
remove the inode from the sysctl_inodes list.  Removing inodes from the
sysctl_inodes list allows proc_sys_prune_dcache to have a progress
guarantee, while still being able to drop all locks.  The fact that
head->unregistering is set in start_unregistering ensures that no more
inodes will be added to the the sysctl_inodes list.

Previously the code did a dance where it delayed calling iput until the
next entry in the list was being considered to ensure the inode remained on
the sysctl_inodes list until the next entry was walked to.  The structure
of the loop in this patch does not need that so is much easier to
understand and maintain.
Reported-by: Andrei Vagin <avagin@gmail.com>
Tested-by: Andrei Vagin <avagin@openvz.org>
Fixes: ace0c791 ("proc/sysctl: Don't grab i_lock under sysctl_lock.")
Fixes: d6cffbbe ("proc/sysctl: prune stale dentries during unregistering")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4dec2f11 upstream.

18a42088 introduced a change to reduce the RX DMA latency on the first reception
when the serial port was opened for reading. However it was claiming a hardirq
unsafe lock after a hardirq safe lock which is not allowed and causes lockdep
to complain verbosely.

This patch changes the code to always start RX DMA earlier, instead of
relying on the flags used to open the serial port removing the code that
was looking for the serial file flags.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f991af3d upstream.

The retry logic for netlink_attachskb() inside sys_mq_notify()
is nasty and vulnerable:

1) The sock refcnt is already released when retry is needed
2) The fd is controllable by user-space because we already
   release the file refcnt

so we when retry but the fd has been just closed by user-space
during this small window, we end up calling netlink_detachskb()
on the error path which releases the sock again, later when
the user-space closes this socket a use-after-free could be
triggered.

Setting 'sock' to NULL here should be sufficient to fix it.
Reported-by: GeneBlue <geneblue.mail@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b61929c6 upstream.

Initialise ctr_completion variable before use.

Cc: <stable@vger.kernel.org>
Signed-off-by: Harsh Jain <harshjain.prof@gmail.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1a3fc2c4 upstream.

There has been a report about a deadlock in the xenbus driver:

[  247.979498] ======================================================
[  247.985688] WARNING: possible circular locking dependency detected
[  247.991882] 4.12.0-rc4-00022-gc4b25c0 #575 Not tainted
[  247.997040] ------------------------------------------------------
[  248.003232] xenbus/91 is trying to acquire lock:
[  248.007875]  (&u->msgbuffer_mutex){+.+.+.}, at: [<ffff00000863e904>]
xenbus_dev_queue_reply+0x3c/0x230
[  248.017163]
[  248.017163] but task is already holding lock:
[  248.023096]  (xb_write_mutex){+.+...}, at: [<ffff00000863a940>]
xenbus_thread+0x5f0/0x798
[  248.031267]
[  248.031267] which lock already depends on the new lock.
[  248.031267]
[  248.039615]
[  248.039615] the existing dependency chain (in reverse order) is:
[  248.047176]
[  248.047176] -> #1 (xb_write_mutex){+.+...}:
[  248.052943]        __lock_acquire+0x1728/0x1778
[  248.057498]        lock_acquire+0xc4/0x288
[  248.061630]        __mutex_lock+0x84/0x868
[  248.065755]        mutex_lock_nested+0x3c/0x50
[  248.070227]        xs_send+0x164/0x1f8
[  248.074015]        xenbus_dev_request_and_reply+0x6c/0x88
[  248.079427]        xenbus_file_write+0x260/0x420
[  248.084073]        __vfs_write+0x48/0x138
[  248.088113]        vfs_write+0xa8/0x1b8
[  248.091983]        SyS_write+0x54/0xb0
[  248.095768]        el0_svc_naked+0x24/0x28
[  248.099897]
[  248.099897] -> #0 (&u->msgbuffer_mutex){+.+.+.}:
[  248.106088]        print_circular_bug+0x80/0x2e0
[  248.110730]        __lock_acquire+0x1768/0x1778
[  248.115288]        lock_acquire+0xc4/0x288
[  248.119417]        __mutex_lock+0x84/0x868
[  248.123545]        mutex_lock_nested+0x3c/0x50
[  248.128016]        xenbus_dev_queue_reply+0x3c/0x230
[  248.133005]        xenbus_thread+0x788/0x798
[  248.137306]        kthread+0x110/0x140
[  248.141087]        ret_from_fork+0x10/0x40

It is rather easy to avoid by dropping xb_write_mutex before calling
xenbus_dev_queue_reply().

Fixes: fd8aa909 ("xen: optimize xenbus
driver for multiple concurrent xenstore accesses").
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ff801b71 upstream.

Stephen reported the following build warning in UP:

kernel/sched/fair.c:2657:9: warning: 'struct sched_domain' declared inside
parameter list
         ^
/home/sfr/next/next/kernel/sched/fair.c:2657:9: warning: its scope is only this
definition or declaration, which is probably not what you want

Hide the numa_wake_affine() inline stub on UP builds to get rid of it.

Fixes: 3fed382b ("sched/numa: Implement NUMA node level wake_affine()")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 815abf5a upstream.

The effective_load() function was only used by the NUMA balancing
code, and not by the regular load balancing code. Now that the
NUMA balancing code no longer uses it either, get rid of it.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jhladky@redhat.com
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20170623165530.22514-5-riel@redhat.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3fed382b upstream.

Since select_idle_sibling() can place a task anywhere on a socket,
comparing loads between individual CPU cores makes no real sense
for deciding whether to do an affine wakeup across sockets, either.

Instead, compare the load between the sockets in a similar way the
load balancer and the numa balancing code do.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jhladky@redhat.com
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20170623165530.22514-4-riel@redhat.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7d894e6e upstream.

Then 'this_cpu' and 'prev_cpu' are in the same socket, select_idle_sibling()
will do its thing regardless of the return value of wake_affine().

Just return true and don't look at all the other things.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jhladky@redhat.com
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20170623165530.22514-3-riel@redhat.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 739294fb upstream.

Several tests in the NAS benchmark seem to run a lot slower with
NUMA balancing enabled, than with NUMA balancing disabled. The
slower run time corresponds with increased idle time.

Overriding the final test of migrate_degrades_locality (but still
doing the other NUMA tests first) seems to improve performance
of those benchmarks.
Reported-by: Jirka Hladky <jhladky@redhat.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/20170623165530.22514-2-riel@redhat.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8655d549 upstream.

A customer has reported a soft-lockup when running an intensive
memory stress test, where the trace on multiple CPU's looks like this:

 RIP: 0010:[<ffffffff810c53fe>]
  [<ffffffff810c53fe>] native_queued_spin_lock_slowpath+0x10e/0x190
...
 Call Trace:
  [<ffffffff81182d07>] queued_spin_lock_slowpath+0x7/0xa
  [<ffffffff811bc331>] change_protection_range+0x3b1/0x930
  [<ffffffff811d4be8>] change_prot_numa+0x18/0x30
  [<ffffffff810adefe>] task_numa_work+0x1fe/0x310
  [<ffffffff81098322>] task_work_run+0x72/0x90

Further investigation showed that the lock contention here is pmd_lock().

The task_numa_work() function makes sure that only one thread is let to perform
the work in a single scan period (via cmpxchg), but if there's a thread with
mmap_sem locked for writing for several periods, multiple threads in
task_numa_work() can build up a convoy waiting for mmap_sem for read and then
all get unblocked at once.

This patch changes the down_read() to the trylock version, which prevents the
build up. For a workload experiencing mmap_sem contention, it's probably better
to postpone the NUMA balancing work anyway. This seems to have fixed the soft
lockups involving pmd_lock(), which is in line with the convoy theory.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170515131316.21909-1-vbabka@suse.czSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1ad3aaf3 upstream.

Hackbench recently suffered a bunch of pain, first by commit:

  4c77b18c ("sched/fair: Make select_idle_cpu() more aggressive")

and then by commit:

  c743f0a5 ("sched/fair, cpumask: Export for_each_cpu_wrap()")

which fixed a bug in the initial for_each_cpu_wrap() implementation
that made select_idle_cpu() even more expensive. The bug was that it
would skip over CPUs when bits were consequtive in the bitmask.

This however gave me an idea to fix select_idle_cpu(); where the old
scheme was a cliff-edge throttle on idle scanning, this introduces a
more gradual approach. Instead of stopping to scan entirely, we limit
how many CPUs we scan.

Initial benchmarks show that it mostly recovers hackbench while not
hurting anything else, except Mason's schbench, but not as bad as the
old thing.

It also appears to recover the tbench high-end, which also suffered like
hackbench.
Tested-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Cc: kitsunyan <kitsunyan@inbox.ru>
Cc: linux-kernel@vger.kernel.org
Cc: lvenanci@redhat.com
Cc: riel@redhat.com
Cc: xiaolong.ye@intel.com
Link: http://lkml.kernel.org/r/20170517105350.hk5m4h4jb6dfr65a@hirez.programming.kicks-ass.netSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c743f0a5 upstream.

More users for for_each_cpu_wrap() have appeared. Promote the construct
to generic cpumask interface.

The implementation is slightly modified to reduce arguments.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Lauro Ramos Venancio <lvenanci@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: lwang@redhat.com
Link: http://lkml.kernel.org/r/20170414122005.o35me2h5nowqkxbv@hirez.programming.kicks-ass.netSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 236222d3 upstream.

According to the Intel datasheet, the REP MOVSB instruction
exposes a pretty heavy setup cost (50 ticks), which hurts
short string copy operations.

This change tries to avoid this cost by calling the explicit
loop available in the unrolled code for strings shorter
than 64 bytes.

The 64 bytes cutoff value is arbitrary from the code logic
point of view - it has been selected based on measurements,
as the largest value that still ensures a measurable gain.

Micro benchmarks of the __copy_from_user() function with
lengths in the [0-63] range show this performance gain
(shorter the string, larger the gain):

 - in the [55%-4%] range on Intel Xeon(R) CPU E5-2690 v4
 - in the [72%-9%] range on Intel Core i7-4810MQ

Other tested CPUs - namely Intel Atom S1260 and AMD Opteron
8216 - show no difference, because they do not expose the
ERMS feature bit.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/4533a1d101fd460f80e21329a34928fad521c1d4.1498744345.git.pabeni@redhat.com
[ Clarified the changelog. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>

commit 67d20418 upstream.

Fixes: a7cd88da ("powerpc/powernv: Move CPU-Offline idle state invocation from smp.c to idle.c")
Cc: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 13b47cfc upstream.

While cleaning up sysfs callback that prints EK we discovered a kernel
memory leak. This commit fixes the issue by zeroing the buffer used for
TPM command/response.

The leak happen when we use either tpm_vtpm_proxy, tpm_ibmvtpm or
xen-tpmfront.

Fixes: 08837438 ("TPM: sysfs functions consolidation")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d1bd4a79 upstream.

If a TPM2 loses power without a TPM2_Shutdown command being issued (a
"disorderly reboot"), it may lose some state that has yet to be
persisted to NVRam, and will increment the DA counter. After the DA
counter gets sufficiently large, the TPM will lock the user out.

NOTE: This only changes behavior on TPM2 devices. Since TPM1 uses sysfs,
and sysfs relies on implicit locking on chip->ops, it is not safe to
allow this code to run in TPM1, or to add sysfs support to TPM2, until
that locking is made explicit.
Signed-off-by: Josh Zimmerman <joshz@google.com>
Fixes: 74d6b3ce ("tpm: fix suspend/resume paths for TPM 2.0")
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f77af151 upstream.

The TPM class has some common shutdown code that must be executed for
all drivers. This adds some needed functionality for that.
Signed-off-by: Josh Zimmerman <joshz@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 74d6b3ce ("tpm: fix suspend/resume paths for TPM 2.0")
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 961ae1d8 upstream.

Before commit 88ffbf3e "GFS2: Use resizable hash table for glocks",
glocks were freed via call_rcu to allow reading the glock hashtable
locklessly using rcu.  This was then changed to free glocks immediately,
which made reading the glock hashtable unsafe.  Bring back the original
code for freeing glocks via call_rcu.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dec08194 upstream.

For AMD Promontory xHCI host, although you can disable USB 2.0 ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.

This will disable wake on connect, disconnect and overcurrent on
AMD Promontory USB2 ports

[checkpatch cleanup and commit message reword -Mathias]
Cc: Tsai Nicholas <nicholas.tsai@amd.com>
Signed-off-by: Jiahau Chang <Lars_Chang@asmedia.com.tw>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 996fab55 upstream.

A new Sierra Wireless EM7305 device ID used in a Toshiba laptop.
Reported-by: Petr Kloc <petr_kloc@yahoo.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>