Thanks to Joilnen Leite <knl_joi@yahoo.com.br> for pointing this out.

This patch:

   - Makes the cdc code handle a Motorola cable modem that stores
     CDC descriptors in the wrong place.  The workaround might be
     helpful for other hardware too.  (This was a 2.4 regression.)

   - Recognizes another Zaurus (PXA 255 based clamshell, not yet
     sold by Sharp in the US).

   - Cleaned the Zaurus stuff up a bit.  Rather than expecting
     a new driver_info struct (or re-using the right one) for
     each new pxa based product, they all use the same one.  So
     patches for new products only need new usb_device_id entries.
     (Also notes the issue that every Zaurus model will need to be
     blacklisted for CDC if the Z code isn't enabled.)

From pavel@ucw.cz

This adds support for another handheld from sharp to 2.6.0-test1

an unknown ioctl shall return ENOTTY, not EINVAL.

Now we just throw urbs at the device as fast as we can.

This is a one-line "obviously correct" patch that Lutz reports
is needed on one ARM platform.

into kroah.com:/home/greg/linux/BK/gregkh-2.6

From mru@users.sourceforge.net

My Netgear FA120 USB2 ethernet adaptor isn't working properly with
Linux 2.6.0-test1.  First off, I had to modify it slightly (patch
below) to make it work at all with USB2.  Now I can send data at the
full expected speed (~11 MB/s).

From mru@users.sourceforge.net

This trivial Makefile patch causes the AX8817x driver to actually be
built.

The recent change made to the irq handling in hcd_endpoint_disable()
caused a problem.  The statement

	local_irq_save (flags);

needs to be outside the rescan loop.  Otherwise, on loop iterations after
the first, flags is always set to indicate that interrupts are disabled.

In fact, since the routine ends with might_sleep() anyway, I don't see any
reason to save the interrupt state at all.  My patch just disables
interrupts at the start and enables them at the end.  I'm not sure that's
how you intended it to work, so you may want to change it a little.

There are two places where the audio driver checks for
endpoint-less interfaces, but the second one doesn't
filter out a garbage warning (without this patch).

Likely it'd be better to remove these warnings from
the driver, and maybe just place them in usbcore if
they'd ever be useful.  But this at least gets rid
of one class of "is this device broken" questions.

This patch makes the shuttle_usbat subdriver use proper DMA I/O buffering.
Although I try to be careful with these changes, I can't test them.  So I
urge you to read through it carefully to verify that nothing seems to be
wrong.

Also set usb_device.dev.release right after initialization to catch any
early devices being destroyed.  I still think there's a few error paths
to correct, but this catches a lot of previous errors.

Added a release callback, as is required, otherwise we can easily oops
if a user grabs a sysfs file and the device is removed from the system.

also detach the threads.

Otherwise we'll leave them around as zombies, waiting for them
to be picked up by their parent. Which might be the execve()
thread itself, causing a deadlock.

Noted by Sean Estabrooks:

There is a bug in "ll_rw_blk.c" handling partial bvec submissions.
For whatever reason the floppy driver was triggering it more than
other users (most likely because most other devices tend to be able
to always complete a full request in one go).

Fixed by updating the proper bio vector index entry.

Add kconfig options to allow excluding either or both the I/O
schedulers.  This can be useful for embedded systems (saves about ~13KB).

All schedulers are enabled by default for non-embedded.

This updates the valkyriefb driver to the new API.

From Paul Mackerras <paulus@samba.org>:

 "It compiles OK, but I haven't been able to test it.  I have simplified
  the driver quite a bit using the knowledge that there can only ever be
  one valkyrie graphics adaptor in a system - it is the built-in
  graphics adaptor on various ancient mac and powermac machines, and we
  access it at a hard-coded address, so we can only handle one."

Documentation/nmi-watchdoc.txt doesn't actually tell what options need to be
enabled in kernel config in order to use NMI watchdog. I for one found it
confusing.

Rename ariadne2 to zorro8390, since this driver supports several NS8390-based
Zorro Ethernet cards. Kill all never used occurrencies of CONFIG_NE2K_ZORRO.

m68k cache updates (from Roman Zippel):
  - Uninline flush_icache_range()
  - Add virt_to_phys_slow() which handles vmalloc()ed space

M68k: Use genrtc on all m68k platforms

M68k: Allow ALLOWINT to be used with other types than short (fixes a problem
with irqs_disabled(), from Roman Zippel)

dmasound: Implement missing SOUND_PCM_READ_RATE ioctl (from Richard Zidlicky)

MIPS: Show the correct logo on DEC and SGI machines.

M68k FPU emulator: Add fgetman, fgetexp and fsqrt (from Michael Müller and
Roman Zippel)