- 23 Mar, 2017 3 commits
-
-
Lendacky, Thomas authored
The ECC bit positions that describe whether the ECC interrupt is for Tx, Rx or descriptor memory and whether the it is a single correctable or double detected error were defined in incorrectly (reversed order). Fix the bit position definitions for these settings so that the proper ECC handling is performed. Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dan Carpenter authored
Presumably if there is an "add" function, there is also a "del" function. But it causes a static checker warning because it looks like a common cut and paste bug. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
-
Arnd Bergmann authored
compile-testing fails when QCOM_SMD is a loadable module: drivers/bluetooth/built-in.o: In function `btqcomsmd_send': btqca.c:(.text+0xa8): undefined reference to `qcom_smd_send' drivers/bluetooth/built-in.o: In function `btqcomsmd_probe': btqca.c:(.text+0x3ec): undefined reference to `qcom_wcnss_open_channel' btqca.c:(.text+0x46c): undefined reference to `qcom_smd_set_drvdata' This clarifies the dependency to allow compile-testing only when SMD is completely disabled, otherwise the dependency on QCOM_SMD will make sure we can link against it. Fixes: e27ee2b1 ("Bluetooth: btqcomsmd: Allow driver to build if COMPILE_TEST is enabled") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> [bjorn: Restructure and clarify dependency to QCOM_WCNSS_CTRL] Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Acked-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
- 22 Mar, 2017 37 commits
-
-
Eric Dumazet authored
Dmitry reported a lockdep splat [1] (false positive) that we can fix by releasing the spinlock before calling icmp_send() from ip_expire() This is a false positive because sending an ICMP message can not possibly re-enter the IP frag engine. [1] [ INFO: possible circular locking dependency detected ] 4.10.0+ #29 Not tainted ------------------------------------------------------- modprobe/12392 is trying to acquire lock: (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] spin_lock include/linux/spinlock.h:299 [inline] (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] __netif_tx_lock include/linux/netdevice.h:3486 [inline] (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 but task is already holding lock: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock include/linux/spinlock.h:299 [inline] (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&(&q->lock)->rlock){+.-...}: validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] ip_defrag+0x3a2/0x4130 net/ipv4/ip_fragment.c:669 ip_check_defrag+0x4e3/0x8b0 net/ipv4/ip_fragment.c:713 packet_rcv_fanout+0x282/0x800 net/packet/af_packet.c:1459 deliver_skb net/core/dev.c:1834 [inline] dev_queue_xmit_nit+0x294/0xa90 net/core/dev.c:1890 xmit_one net/core/dev.c:2903 [inline] dev_hard_start_xmit+0x16b/0xab0 net/core/dev.c:2923 sch_direct_xmit+0x31f/0x6d0 net/sched/sch_generic.c:182 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_resolve_output+0x6b9/0xb10 net/core/neighbour.c:1308 neigh_output include/net/neighbour.h:478 [inline] ip_finish_output2+0x8b8/0x15a0 net/ipv4/ip_output.c:228 ip_do_fragment+0x1d93/0x2720 net/ipv4/ip_output.c:672 ip_fragment.constprop.54+0x145/0x200 net/ipv4/ip_output.c:545 ip_finish_output+0x82d/0xe10 net/ipv4/ip_output.c:314 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 raw_sendmsg+0x26de/0x3a00 net/ipv4/raw.c:655 inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:761 sock_sendmsg_nosec net/socket.c:633 [inline] sock_sendmsg+0xca/0x110 net/socket.c:643 ___sys_sendmsg+0x4a3/0x9f0 net/socket.c:1985 __sys_sendmmsg+0x25c/0x750 net/socket.c:2075 SYSC_sendmmsg net/socket.c:2106 [inline] SyS_sendmmsg+0x35/0x60 net/socket.c:2101 do_syscall_64+0x2e8/0x930 arch/x86/entry/common.c:281 return_from_SYSCALL_64+0x0/0x7a -> #0 (_xmit_ETHER#2){+.-...}: check_prev_add kernel/locking/lockdep.c:1830 [inline] check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940 validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] __netif_tx_lock include/linux/netdevice.h:3486 [inline] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_hh_output include/net/neighbour.h:468 [inline] neigh_output include/net/neighbour.h:476 [inline] ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228 ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394 icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754 ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239 call_timer_fn+0x241/0x820 kernel/time/timer.c:1268 expire_timers kernel/time/timer.c:1307 [inline] __run_timers+0x960/0xcf0 kernel/time/timer.c:1601 run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614 __do_softirq+0x31f/0xbe7 kernel/softirq.c:284 invoke_softirq kernel/softirq.c:364 [inline] irq_exit+0x1cc/0x200 kernel/softirq.c:405 exiting_irq arch/x86/include/asm/apic.h:657 [inline] smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962 apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707 __read_once_size include/linux/compiler.h:254 [inline] atomic_read arch/x86/include/asm/atomic.h:26 [inline] rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline] __rcu_is_watching kernel/rcu/tree.c:1133 [inline] rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147 rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293 radix_tree_deref_slot include/linux/radix-tree.h:238 [inline] filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335 do_fault_around mm/memory.c:3231 [inline] do_read_fault mm/memory.c:3265 [inline] do_fault+0xbd5/0x2080 mm/memory.c:3370 handle_pte_fault mm/memory.c:3600 [inline] __handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714 handle_mm_fault+0x1e2/0x480 mm/memory.c:3751 __do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397 do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460 page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&(&q->lock)->rlock); lock(_xmit_ETHER#2); lock(&(&q->lock)->rlock); lock(_xmit_ETHER#2); *** DEADLOCK *** 10 locks held by modprobe/12392: #0: (&mm->mmap_sem){++++++}, at: [<ffffffff81329758>] __do_page_fault+0x2b8/0xb60 arch/x86/mm/fault.c:1336 #1: (rcu_read_lock){......}, at: [<ffffffff8188cab6>] filemap_map_pages+0x1e6/0x1570 mm/filemap.c:2324 #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] spin_lock include/linux/spinlock.h:299 [inline] #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] pte_alloc_one_map mm/memory.c:2944 [inline] #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] alloc_set_pte+0x13b8/0x1b90 mm/memory.c:3072 #3: (((&q->timer))){+.-...}, at: [<ffffffff81627e72>] lockdep_copy_map include/linux/lockdep.h:175 [inline] #3: (((&q->timer))){+.-...}, at: [<ffffffff81627e72>] call_timer_fn+0x1c2/0x820 kernel/time/timer.c:1258 #4: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock include/linux/spinlock.h:299 [inline] #4: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201 #5: (rcu_read_lock){......}, at: [<ffffffff8389a633>] ip_expire+0x1b3/0x6c0 net/ipv4/ip_fragment.c:216 #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] spin_trylock include/linux/spinlock.h:309 [inline] #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] icmp_xmit_lock net/ipv4/icmp.c:219 [inline] #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] icmp_send+0x803/0x1c80 net/ipv4/icmp.c:681 #7: (rcu_read_lock_bh){......}, at: [<ffffffff838ab9a1>] ip_finish_output2+0x2c1/0x15a0 net/ipv4/ip_output.c:198 #8: (rcu_read_lock_bh){......}, at: [<ffffffff836d1dee>] __dev_queue_xmit+0x23e/0x1e60 net/core/dev.c:3324 #9: (dev->qdisc_running_key ?: &qdisc_running_key){+.....}, at: [<ffffffff836d3a27>] dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 stack backtrace: CPU: 0 PID: 12392 Comm: modprobe Not tainted 4.10.0+ #29 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:16 [inline] dump_stack+0x2ee/0x3ef lib/dump_stack.c:52 print_circular_bug+0x307/0x3b0 kernel/locking/lockdep.c:1204 check_prev_add kernel/locking/lockdep.c:1830 [inline] check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940 validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] __netif_tx_lock include/linux/netdevice.h:3486 [inline] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_hh_output include/net/neighbour.h:468 [inline] neigh_output include/net/neighbour.h:476 [inline] ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228 ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394 icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754 ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239 call_timer_fn+0x241/0x820 kernel/time/timer.c:1268 expire_timers kernel/time/timer.c:1307 [inline] __run_timers+0x960/0xcf0 kernel/time/timer.c:1601 run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614 __do_softirq+0x31f/0xbe7 kernel/softirq.c:284 invoke_softirq kernel/softirq.c:364 [inline] irq_exit+0x1cc/0x200 kernel/softirq.c:405 exiting_irq arch/x86/include/asm/apic.h:657 [inline] smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962 apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707 RIP: 0010:__read_once_size include/linux/compiler.h:254 [inline] RIP: 0010:atomic_read arch/x86/include/asm/atomic.h:26 [inline] RIP: 0010:rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline] RIP: 0010:__rcu_is_watching kernel/rcu/tree.c:1133 [inline] RIP: 0010:rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147 RSP: 0000:ffff8801c391f120 EFLAGS: 00000a03 ORIG_RAX: ffffffffffffff10 RAX: dffffc0000000000 RBX: ffff8801c391f148 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 000055edd4374000 RDI: ffff8801dbe1ae0c RBP: ffff8801c391f1a0 R08: 0000000000000002 R09: 0000000000000000 R10: dffffc0000000000 R11: 0000000000000002 R12: 1ffff10038723e25 R13: ffff8801dbe1ae00 R14: ffff8801c391f680 R15: dffffc0000000000 </IRQ> rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293 radix_tree_deref_slot include/linux/radix-tree.h:238 [inline] filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335 do_fault_around mm/memory.c:3231 [inline] do_read_fault mm/memory.c:3265 [inline] do_fault+0xbd5/0x2080 mm/memory.c:3370 handle_pte_fault mm/memory.c:3600 [inline] __handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714 handle_mm_fault+0x1e2/0x480 mm/memory.c:3751 __do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397 do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460 page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011 RIP: 0033:0x7f83172f2786 RSP: 002b:00007fffe859ae80 EFLAGS: 00010293 RAX: 000055edd4373040 RBX: 00007f83175111c8 RCX: 000055edd4373238 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00007f8317510970 RBP: 00007fffe859afd0 R08: 0000000000000009 R09: 0000000000000000 R10: 0000000000000064 R11: 0000000000000000 R12: 000055edd4373040 R13: 0000000000000000 R14: 00007fffe859afe8 R15: 0000000000000000 Signed-off-by:Eric Dumazet <edumazet@google.com> Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
-
Eric Dumazet authored
icsk_ack.lrcvtime has a 0 value at socket creation time. tcpi_last_data_recv can have bogus value if no payload is ever received. This patch initializes icsk_ack.lrcvtime for active sessions in tcp_finish_connect(), and for passive sessions in tcp_create_openreq_child() Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
-
Stanislaw Gruszka authored
Commit 2ae0f17d ("genetlink: use idr to track families") replaced if (++n < fams_to_skip) continue; into: if (n++ < fams_to_skip) continue; This subtle change cause that on retry ctrl_dumpfamily() call we omit one family that failed to do ctrl_fill_info() on previous call, because cb->args[0] = n number counts also family that failed to do ctrl_fill_info(). Patch fixes the problem and avoid confusion in the future just decrease n counter when ctrl_fill_info() fail. User visible problem caused by this bug is failure to get access to some genetlink family i.e. nl80211. However problem is reproducible only if number of registered genetlink families is big enough to cause second call of ctrl_dumpfamily(). Cc: Xose Vazquez Perez <xose.vazquez@gmail.com> Cc: Larry Finger <Larry.Finger@lwfinger.net> Cc: Johannes Berg <johannes@sipsolutions.net> Fixes: 2ae0f17d ("genetlink: use idr to track families") Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Acked-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Daniel Borkmann authored
In sk_clone_lock(), we create a new socket and inherit most of the parent's members via sock_copy() which memcpy()'s various sections. Now, in case the parent socket had a BPF socket filter attached, then newsk->sk_filter points to the same instance as the original sk->sk_filter. sk_filter_charge() is then called on the newsk->sk_filter to take a reference and should that fail due to hitting max optmem, we bail out and release the newsk instance. The issue is that commit 278571ba ("net: filter: simplify socket charging") wrongly combined the dismantle path with the failure path of xfrm_sk_clone_policy(). This means, even when charging failed, we call sk_free_unlock_clone() on the newsk, which then still points to the same sk_filter as the original sk. Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually where it tests for present sk_filter and calls sk_filter_uncharge() on it, which potentially lets sk_omem_alloc wrap around and releases the eBPF prog and sk_filter structure from the (still intact) parent. Fix it by making sure that when sk_filter_charge() failed, we reset newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(), so that we don't mess with the parents sk_filter. Only if xfrm_sk_clone_policy() fails, we did reach the point where either the parent's filter was NULL and as a result newsk's as well or where we previously had a successful sk_filter_charge(), thus for that case, we do need sk_filter_uncharge() to release the prior taken reference on sk_filter. Fixes: 278571ba ("net: filter: simplify socket charging") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Eric Dumazet authored
Alexander reported a KMSAN splat caused by reads of uninitialized field (tb_id_in) from user provided struct fib_result_nl It turns out nl_fib_input() sanity tests on user input is a bit wrong : User can pretend nlh->nlmsg_len is big enough, but provide at sendmsg() time a too small buffer. Reported-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
-
Alexei Starovoitov authored
In both kmalloc and prealloc mode the bpf_map_update_elem() is using per-cpu extra_elems to do atomic update when the map is full. There are two issues with it. The logic can be misused, since it allows max_entries+num_cpus elements to be present in the map. And alloc_extra_elems() at map creation time can fail percpu alloc for large map values with a warn: WARNING: CPU: 3 PID: 2752 at ../mm/percpu.c:892 pcpu_alloc+0x119/0xa60 illegal size (32824) or align (8) for percpu allocation The fixes for both of these issues are different for kmalloc and prealloc modes. For prealloc mode allocate extra num_possible_cpus elements and store their pointers into extra_elems array instead of actual elements. Hence we can use these hidden(spare) elements not only when the map is full but during bpf_map_update_elem() that replaces existing element too. That also improves performance, since pcpu_freelist_pop/push is avoided. Unfortunately this approach cannot be used for kmalloc mode which needs to kfree elements after rcu grace period. Therefore switch it back to normal kmalloc even when full and old element exists like it was prior to commit 6c905981 ("bpf: pre-allocate hash map elements"). Add tests to check for over max_entries and large map values. Reported-by:
Dave Jones <davej@codemonkey.org.uk> Fixes: 6c905981 ("bpf: pre-allocate hash map elements") Signed-off-by:
Martin KaFai Lau <kafai@fb.com> Signed-off-by:
-
Govindarajulu Varadarajan authored
update enic maintainers Signed-off-by:
Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by:
-
Doug Berger authored
Commit 6ac3ce82 ("net: bcmgenet: Remove excessive PHY reset") removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and bcmgenet_internal_phy_setup() functions. In so doing it broke the reset of the internal PHY devices used by the GENETv1-GENETv3 which required this reset before the UniMAC was enabled. It also broke the internal GPHY devices used by the GENETv4 because the config_init that installed the AFE workaround was no longer occurring after the reset of the GPHY performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup(). In addition the code in bcmgenet_internal_phy_setup() related to the "enable APD" comment goes with the bcmgenet_mii_reset() so it should have also been removed. Commit bd4060a6 ("net: bcmgenet: Power on integrated GPHY in bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the bcmgenet_power_up() function, but failed to remove it from the bcmgenet_internal_phy_setup() function. Had it done so, the bcmgenet_internal_phy_setup() function would have been empty and could have been removed at that time. Commit 5dbebbb4 ("net: bcmgenet: Software reset EPHY after power on") was submitted to correct the functional problems introduced by commit 6ac3ce82 ("net: bcmgenet: Remove excessive PHY reset"). It was included in v4.4 and made available on 4.3-stable. Unfortunately, it didn't fully revert the commit because this bcmgenet_mii_reset() doesn't apply the soft reset to the internal GPHY used by GENETv4 like the previous one did. This prevents the restoration of the AFE work- arounds for internal GPHY devices after the bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup(). This commit takes the alternate approach of removing the unnecessary bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3 so that when bcmgenet_mii_reset() was restored it should have only gone into bcmgenet_power_up(). This will avoid the problems while also removing the redundancy (and hopefully some of the confusion). Fixes: 6ac3ce82 ("net: bcmgenet: Remove excessive PHY reset") Signed-off-by:
Doug Berger <opendmb@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Alexander Potapenko authored
In the case udp_sk(sk)->pending is AF_INET6, udpv6_sendmsg() would jump to do_append_data, skipping the initialization of sockc.tsflags. Fix the problem by moving sockc.tsflags initialization earlier. The bug was detected with KMSAN. Fixes: c14ac945 ("sock: enable timestamping using control messages") Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
-
David S. Miller authored
YASUAKI ISHIMATSU says: ==================== fjes: Do not load fjes driver The fjes driver is used only by FUJITSU servers and almost of all servers in the world never use it. But currently if ACPI PNP0C02 is defined in the ACPI table, the following message is always shown: "FUJITSU Extended Socket Network Device Driver - version 1.2 - Copyright (c) 2015 FUJITSU LIMITED" The message makes users confused because there is no reason that the message is shown in other vendor servers. To avoid the confusion, the patch adds several checks. v3: - Rebase on latest net tree. - Add _STA method check to avoid loading fjes driver. v2: - Order local variable declarations from longest to shortest line ==================== Signed-off-by: -
Yasuaki Ishimatsu authored
The extended device socket cannot turn on/off while system is running. So when system boots up and the device is not power on, the fjes driver does not need be loaded. To check the status of the device, the patch adds ACPI _STA method check. Signed-off-by:
Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com> CC: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by:
-
Yasuaki Ishimatsu authored
The fjes driver is used only by FUJITSU servers and almost of all servers in the world never use it. But currently if ACPI PNP0C02 is defined in the ACPI table, the following message is always shown: "FUJITSU Extended Socket Network Device Driver - version 1.2 - Copyright (c) 2015 FUJITSU LIMITED" The message makes users confused because there is no reason that the message is shown in other vendor servers. To avoid the confusion, the patch adds a check that the server has a extended socket device or not. Signed-off-by:
-
David S. Miller authored
Saeed Mahameed says: ==================== Mellanox mlx5 fixes 2017-03-21 This series contains some mlx5 core and ethernet driver fixes. For -stable: net/mlx5e: Count LRO packets correctly (for kernel >= 4.2) net/mlx5e: Count GSO packets correctly (for kernel >= 4.2) net/mlx5: Increase number of max QPs in default profile (for kernel >= 4.0) net/mlx5e: Avoid supporting udp tunnel port ndo for VF reps (for kernel >= 4.10) net/mlx5e: Use the proper UAPI values when offloading TC vlan actions (for kernel >= v4.9) net/mlx5: E-Switch, Don't allow changing inline mode when flows are configured (for kernel >= 4.10) net/mlx5e: Change the TC offload rule add/del code path to be per NIC or E-Switch (for kernel >= 4.10) net/mlx5: Add missing entries for set/query rate limit commands (for kernel >= 4.8) ==================== Signed-off-by: -
Gal Pressman authored
RX packets statistics ('rx_packets' counter) used to count LRO packets as one, even though it contains multiple segments. This patch will increment the counter by the number of segments, and align the driver with the behavior of other drivers in the stack. Note that no information is lost in this patch due to 'rx_lro_packets' counter existence. Before, ethtool showed: $ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets" rx_packets: 435277 rx_lro_packets: 35847 rx_packets_phy: 1935066 Now, we will see the more logical statistics: $ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets" rx_packets: 1935066 rx_lro_packets: 35847 rx_packets_phy: 1935066 Fixes: e586b3b0 ("net/mlx5: Ethernet Datapath files") Signed-off-by:Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Acked-by:
-
Gal Pressman authored
TX packets statistics ('tx_packets' counter) used to count GSO packets as one, even though it contains multiple segments. This patch will increment the counter by the number of segments, and align the driver with the behavior of other drivers in the stack. Note that no information is lost in this patch due to 'tx_tso_packets' counter existence. Before, ethtool showed: $ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets" tx_packets: 61340 tx_tso_packets: 60954 tx_packets_phy: 2451115 Now, we will see the more logical statistics: $ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets" tx_packets: 2451115 tx_tso_packets: 60954 tx_packets_phy: 2451115 Fixes: e586b3b0 ("net/mlx5: Ethernet Datapath files") Signed-off-by: -
Maor Gottlieb authored
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a limit preventing some applications to allocate needed QPs amount. Double the size to 256K. Fixes: e126ba97 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by:
Maor Gottlieb <maorg@mellanox.com> Signed-off-by:
-
Paul Blakey authored
This was added to allow the TC offloading code to identify offloading encap/decap vxlan rules. The VF reps are effectively related to the same mlx5 PCI device as the PF. Since the kernel invokes the (say) delete ndo for each netdev, the FW erred on multiple vxlan dst port deletes when the port was deleted from the system. We fix that by keeping the registration to be carried out only by the PF. Since the PF serves as the uplink device, the VF reps will look up a port there and realize if they are ok to offload that. Tested: <SETUP VFS> <SETUP switchdev mode to have representors> ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999 ip link set vxlan1 up ip link del dev vxlan1 Fixes: 4a25730e ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors') Signed-off-by:
Paul Blakey <paulb@mellanox.com> Reviewed-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Or Gerlitz authored
Currently we use the non UAPI values and we miss erring on the modify action which is not supported, fix that. Fixes: 8b32580d ('net/mlx5e: Add TC vlan action for SRIOV offloads') Signed-off-by:
Petr Machata <petrm@mellanox.com> Reviewed-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Roi Dayan authored
Changing the eswitch inline mode can potentially cause already configured flows not to match the policy. E.g. set policy L4, add some L4 rules, set policy to L2 --> bad! Hence we disallow it. Keep track of how many offloaded rules are now set and refuse inline mode changes if this isn't zero. Fixes: bffaa916 ("net/mlx5: E-Switch, Add control for inline mode") Signed-off-by:
Roi Dayan <roid@mellanox.com> Reviewed-by:
-
Or Gerlitz authored
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch offloading use case, and push the latter into the e-switch code. This provides better separation and is to be used in down-stream patch for applying a fix. Fixes: bffaa916 ("net/mlx5: E-Switch, Add control for inline mode") Signed-off-by:
-
Or Gerlitz authored
The switch cases for the rate limit set and query commands were missing, which could get us wrong under fw error or driver reset flow, fix that. Fixes: 1466cc5b ('net/mlx5: Rate limit tables support') Signed-off-by:
Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-for-davem-2017-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo says: ==================== wireless-drivers fixes for 4.11 iwlwifi * fix a user reported warning in DQA mwifiex * fix a potential double free * fix lost early debug logs * fix init wakeup warning message from device framework * add Ganapathi and Xinming as maintainers ath10k * fix regression with QCA6174 during resume and firmware crash ==================== Signed-off-by:
-
Ying Xue authored
Until now, tipc_nametbl_unsubscribe() is called at subscriptions reference count cleanup. Usually the subscriptions cleanup is called at subscription timeout or at subscription cancel or at subscriber delete. We have ignored the possibility of this being called from other locations, which causes deadlock as we try to grab the tn->nametbl_lock while holding it already. CPU1: CPU2: ---------- ---------------- tipc_nametbl_publish spin_lock_bh(&tn->nametbl_lock) tipc_nametbl_insert_publ tipc_nameseq_insert_publ tipc_subscrp_report_overlap tipc_subscrp_get tipc_subscrp_send_event tipc_close_conn tipc_subscrb_release_cb tipc_subscrb_delete tipc_subscrp_put tipc_subscrp_put tipc_subscrp_kref_release tipc_nametbl_unsubscribe spin_lock_bh(&tn->nametbl_lock) <<grab nametbl_lock again>> CPU1: CPU2: ---------- ---------------- tipc_nametbl_stop spin_lock_bh(&tn->nametbl_lock) tipc_purge_publications tipc_nameseq_remove_publ tipc_subscrp_report_overlap tipc_subscrp_get tipc_subscrp_send_event tipc_close_conn tipc_subscrb_release_cb tipc_subscrb_delete tipc_subscrp_put tipc_subscrp_put tipc_subscrp_kref_release tipc_nametbl_unsubscribe spin_lock_bh(&tn->nametbl_lock) <<grab nametbl_lock again>> In this commit, we advance the calling of tipc_nametbl_unsubscribe() from the refcount cleanup to the intended callers. Fixes: d094c4d5 ("tipc: add subscription refcount to avoid invalid delete") Reported-by:John Thompson <thompa.atl@gmail.com> Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by:
-
Xin Long authored
This patch is to remove the unnecessary temporary variable 'err' from sctp_association_init. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Xin Long authored
sctp_stream_free uses struct sctp_stream as a param, but struct sctp_stream is defined after it's declaration. This patch is to declare struct sctp_stream before sctp_stream_free. Fixes: a8386317 ("sctp: prepare asoc stream for stream reconf") Signed-off-by:
-
Arnd Bergmann authored
With posix timers having become optional, we get a build error with the cpts time sync option of the CPSW driver: drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts': drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration] This adds a hard dependency on PTP_CLOCK to avoid the problem, as building it without PTP support makes no sense anyway. Fixes: baa73d9e ("posix-timers: Make them configurable") Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: stable@vger.kernel.org Signed-off-by:
Nicolas Pitre <nico@linaro.org> Signed-off-by:
-
Arnd Bergmann authored
The dependency is reversed: cpsw and netcp call into cpts, but cpts depends on the other two in Kconfig. This can lead to cpts being a loadable module and its callers built-in: drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove': cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release' drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler': cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp' drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler': cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp' drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop': As a workaround, I'm introducing another Kconfig symbol to control the compilation of cpts, while making the actual module controlled by a silent symbol that is =y when necessary. Fixes: 6246168b ("net: ethernet: ti: netcp: add support of cpts") Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
-
David S. Miller authored
Hayes Wang says: ==================== r8152: fix the rx settings of RTL8153 The RMS and the rx early size should base on the same rx size. However, the RMS is set to 9K bytes now and the rx early depends on mtu. For using the rx buffer effectively, sync the two settings according to the mtu. ==================== Signed-off-by: -
hayeswang authored
revert commit a59e6d81 ("r8152: correct the rx early size") and fix the rx early size as (rx buffer size - rx packet size - rx desc size - alignment) / 4 Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
hayeswang authored
Set the received maximum size (RMS) according to the mtu size. It is unnecessary to receive a packet which is more than the size we could transmit. Besides, this could let the rx buffer be used effectively. Signed-off-by:
-
Tejun Heo authored
The net_cls controller controls the classid field of each socket which is associated with the cgroup. Because the classid is per-socket attribute, when a task migrates to another cgroup or the configured classid of the cgroup changes, the controller needs to walk all sockets and update the classid value, which was implemented by 3b13758f ("cgroups: Allow dynamically changing net_classid"). While the approach is not scalable, migrating tasks which have a lot of fds attached to them is rare and the cost is born by the ones initiating the operations. However, for simplicity, both the migration and classid config change paths call update_classid() which scans all fds of all tasks in the target css. This is an overkill for the migration path which only needs to cover a much smaller subset of tasks which are actually getting migrated in. On cgroup v1, this can lead to unexpected scalability issues when one tries to migrate a task or process into a net_cls cgroup which already contains a lot of fds. Even if the migration traget doesn't have many to get scanned, update_classid() ends up scanning all fds in the target cgroup which can be extremely numerous. Unfortunately, on cgroup v2 which doesn't use net_cls, the problem is even worse. Before bfc2cf6f ("cgroup: call subsys->*attach() only for subsystems which are actually affected by migration"), cgroup core would call the ->css_attach callback even for controllers which don't see actual migration to a different css. As net_cls is always disabled but still mounted on cgroup v2, whenever a process is migrated on the cgroup v2 hierarchy, net_cls sees identity migration from root to root and cgroup core used to call ->css_attach callback for those. The net_cls ->css_attach ends up calling update_classid() on the root net_cls css to which all processes on the system belong to as the controller isn't used. This makes any cgroup v2 migration O(total_number_of_fds_on_the_system) which is horrible and easily leads to noticeable stalls triggering RCU stall warnings and so on. The worst symptom is already fixed in upstream by bfc2cf6f ("cgroup: call subsys->*attach() only for subsystems which are actually affected by migration"); however, backporting that commit is too invasive and we want to avoid other cases too. This patch updates net_cls's cgrp_attach() to iterate fds of only the processes which are actually getting migrated. This removes the surprising migration cost which is dependent on the total number of fds in the target cgroup. As this leaves write_classid() the only user of update_classid(), open-code the helper into write_classid(). Reported-by:
David Goode <dgoode@fb.com> Fixes: 3b13758f ("cgroups: Allow dynamically changing net_classid") Cc: stable@vger.kernel.org # v4.4+ Cc: Nina Schiff <ninasc@fb.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Tony Lindgren authored
This gets qmicli working with the MDM6600 modem. Cc: Bjørn Mork <bjorn@mork.no> Reviewed-by:
Sebastian Reichel <sre@kernel.org> Tested-by:
Tony Lindgren <tony@atomide.com> Acked-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Zi Shen Lim authored
Merge of 'linux-kselftest-4.11-rc1': 1. Partially removed use of 'test_objs' target, breaking force rebuild of BPFOBJ, introduced in commit d498f871 ("bpf: Rebuild bpf.o for any dependency update"). Update target so dependency on BPFOBJ is restored. 2. Introduced commit 2047f1d8 ("selftests: Fix the .c linking rule") which fixes order of LDLIBS. Commit d02d8986 ("bpf: Always test unprivileged programs") added libcap dependency into CFLAGS. Use LDLIBS instead to fix linking of test_verifier. 3. Introduced commit d83c3ba0 ("selftests: Fix selftests build to just build, not run tests"). Reordering the Makefile allows us to remove the 'all' target. Tested both: selftests/bpf$ make and selftests$ make TARGETS=bpf on Ubuntu 16.04.2. Signed-off-by:
Zi Shen Lim <zlim.lnx@gmail.com> Acked-by:
Shuah Khan <shuahkh@osg.samsung.com> Signed-off-by:
-
Soheil Hassas Yeganeh authored
SOF_TIMESTAMPING_OPT_STATS can be enabled and disabled while packets are collected on the error queue. So, checking SOF_TIMESTAMPING_OPT_STATS in sk->sk_tsflags is not enough to safely assume that the skb contains OPT_STATS data. Add a bit in sock_exterr_skb to indicate whether the skb contains opt_stats data. Fixes: 1c885808 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING") Reported-by:
JongHwan Kim <zzoru007@gmail.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Soheil Hassas Yeganeh authored
__sock_recv_timestamp can be called for both normal skbs (for receive timestamps) and for skbs on the error queue (for transmit timestamps). Commit 1c885808 (tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING) assumes any skb passed to __sock_recv_timestamp are from the error queue, containing OPT_STATS in the content of the skb. This results in accessing invalid memory or generating junk data. To fix this, set skb->pkt_type to PACKET_OUTGOING for packets on the error queue. This is safe because on the receive path on local sockets skb->pkt_type is never set to PACKET_OUTGOING. With that, copy OPT_STATS from a packet, only if its pkt_type is PACKET_OUTGOING. Fixes: 1c885808 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING") Reported-by:
-
Xin Long authored
This patch is to fix the issue that sctp_prsctp_prune_sent forgot to update q->out_qlen when removing a chunk from unsent queue. Fixes: 8dbdf1f5 ("sctp: implement prsctp PRIO policy") Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
-
Xin Long authored
As tp->dst_pending_confirm's value can only be set 0 or 1, this patch is to change to define it as a bit instead of __u32. Signed-off-by:
-
