- 25 May, 2020 15 commits
-
-
Martin Blumenstingl authored
There is now a dedicated driver for these SoCs making the old compatible obsolete. Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
Felipe Balbi <balbi@kernel.org>
-
Martin Blumenstingl authored
The registers which are managed by the meson-gxl-usb3 PHY driver are actually "USB control" registers (which are "glue" registers which manage OTG detection and routing of the OTG capable port between the DWC2 peripheral-only controller and the DWC3 host-only controller). Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-g12a-usb driver supports the USB control registers on GXL and GXM SoCs (these were previously managed by the meson-gxl-usb3 PHY driver). Signed-off-by:
-
Martin Blumenstingl authored
Add the correcly architectured USB Glue node and adapt all the Amlogic GXL and GXM board to the new organization. Signed-off-by:
-
Neil Armstrong authored
In order to add support for the Amlogic GXL/GXM USB Glue, this adds the corresponding : - PHY names - clock names - USB2 PHY init and mode set - regmap setup Reviewed-by:
-
Neil Armstrong authored
On the Amlogic GXL/GXM SoCs, the OTG PHY status signals are always connected to the DWC3 controller, thus crashing the controller when switching to OTG mode when port is not populated with a device/cable to Host. Amlogic added a bit to disconnect the OTG PHY status signals from the DWC3 to be used when switching the OTG PHY as Device to the DWC2 controller. The drawback is that it makes the DWC3 port state machine stall and needs a full reset of the DWC3 controller to get connect status to the port connected to the OTG PHY, but not the other one. Reviewed-by:
-
Neil Armstrong authored
Refactor the USB init code patch to handle the Amlogic GXL/GXM needing to initialize the OTG port as Peripheral mode for the DWC2 IP to probe correctly. A secondary, post_init callback is added to setup the OTG PHY mode after powering up the PHYs and before probing the DWC2 and DWC3 controllers. Reviewed-by:
-
Jason Yan authored
Fix the following gcc warning: drivers/usb/gadget/udc/gr_udc.c:51:19: warning: ‘driver_desc’ defined but not used [-Wunused-const-variable=] static const char driver_desc[] = DRIVER_DESC; ^~~~~~~~~~~ Reported-by:Hulk Robot <hulkci@huawei.com> Signed-off-by:
Jason Yan <yanaijie@huawei.com> Signed-off-by:
-
Christophe JAILLET authored
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'. Fixes: 48ba02b2 ("usb: gadget: add udc driver for max3420") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Nishad Kamdar authored
This patch corrects the SPDX License Identifier style in header files related to MediaTek USB3 Dual Role controller. For C header files Documentation/process/license-rules.rst mandates C-like comments (opposed to C source files where C++ style should be used). Changes made by using a script provided by Joe Perches here: https://lkml.org/lkml/2019/2/7/46. Reviewed-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Suggested-by:
Joe Perches <joe@perches.com> Signed-off-by:
Nishad Kamdar <nishadkamdar@gmail.com> Signed-off-by:
-
Peter Chen authored
During device mode initialization, lots of device information are printed to console, see below. Change them as debug message. cdns-usb3 5b130000.cdns3: Initialized ep0 support: cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO Reviewed-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Peter Chen <peter.chen@nxp.com> Signed-off-by:
-
Peter Chen authored
And delete cdsn3_hw_role_state_machine declare which doesn't be needed. Reviewed-by:
-
Peter Chen authored
In short, we have three kinds of role switches: - Based on SoC: ID and VBUS - Based on external connnctor, eg, Type-C or GPIO Connector - Based on user choices through sysfs Since HW handling and usb-role-switch handling are at different places, we do not need role_override any more, and this flag could not judge external connector case well. With role_override deleted, We use cdns3_hw_role_switch for the 1st use case, and usb-role-switch for the 2nd and 3rd cases. Reviewed-by:
-
Peter Chen authored
After that, the role switch device (eg, Type-C device) could call cdns3_role_set to finish the role switch. Reviewed-by:
-
Thinh Nguyen authored
If there are still pending requests because no TRB was available, prepare more when started requests are completed. Introduce dwc3_gadget_ep_should_continue() to check for incomplete and pending requests to resume updating new TRBs to the controller's TRB cache. Signed-off-by:
Thinh Nguyen <thinhn@synopsys.com> Signed-off-by:
-
Nagarjuna Kristam authored
Register vbus_draw to gadget ops and update corresponding vbus draw current to usb_phy. Signed-off-by:
Nagarjuna Kristam <nkristam@nvidia.com> Signed-off-by:
-
- 05 May, 2020 25 commits
-
-
Thinh Nguyen authored
If the driver issued START_TRANSFER and received a no-resource status, then generally there are a few reasons for this: 1) The driver did not allocate resource for the endpoint during power-on-reset initialization. 2) The transfer resource was reset. At this moment, we don't do this in the driver, but it occurs when the driver issues START_CONFIG cmd to ep0 with resource index=2. 3) The driver issues the START_TRANSFER command to an already started endpoint. Usually, this is because the END_TRANSFER command hasn't completed yet. Print out a warning to help debug this issue in the driver. Signed-off-by:
-
Thinh Nguyen authored
After a number of unsuccessful start isoc attempts due to bus-expiry status, issue END_TRANSFER command and retry on the next XferNotReady event. Signed-off-by:
-
Thinh Nguyen authored
As long as the START_TRANSFER command completes, it provides the resource index of the endpoint. Use this when we need to issue END_TRANSFER command to an isoc endpoint to retry with a new XferNotReady event. Signed-off-by:
-
Thinh Nguyen authored
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we should properly end an active transfer and give back all the started requests. However if it's for an isoc endpoint, the failure maybe due to bus-expiry status. In this case, don't give back the requests and wait for the next retry. Fixes: 72246da4 ("usb: Introduce DesignWare USB3 DRD Driver") Signed-off-by:
-
Thinh Nguyen authored
If the driver is configured to use DRD role-switch, let the drd code path decide the default dr_mode. Signed-off-by:
-
Thinh Nguyen authored
If the driver is configured to use DRD role-switch, it's not OTG. There won't be OTG irq to free. Check for dwc->otg_irq before freeing it. Signed-off-by:
-
Neil Armstrong authored
Refactor the USB2 PHY init code patch to handle the Amlogic GXL/GXM not having the PHY mode control registers in the Glue but in the PHY registers. The Amlogic GXL/GXM will call phy_set_mode() instead of programming the PHY mode control registers, thus add two new callbacks to the SoC match data. Reviewed-by:
-
Neil Armstrong authored
The dwc3_meson_g12a_usb_init function can return an error, check it. Fixes: c9999337 ("usb: dwc3: Add Amlogic G12A DWC3 glue") Reviewed-by:
-
Neil Armstrong authored
In order to support the Amlogic GXL/GXM SoCs, the reset line must be handled as shared since also used by the PHYs. Reviewed-by:
-
Neil Armstrong authored
On the Amlogic GXL/GXM SoCs, only the USB control registers are available, the PHY mode being handled in the PHY registers. Thus, handle the PHY mode registers in separate regmaps and prepare support for Amlogic GXL/GXM SoCs by moving the regmap setup in a callback set in the SoC match data. Reviewed-by:
-
Neil Armstrong authored
To handle the variable USB2 PHY counts on GXL and GXM SoCs, add the possible PHY names for each SoC in the compatible match data. Reviewed-by:
Hanjie Lin <hanjie.lin@amlogic.com> Signed-off-by:
-
Neil Armstrong authored
dt-bindings: usb: amlogic,meson-g12a-usb-ctrl: add the Amlogic GXL and GXM Families USB Glue Bindings The Amlogic GXL and GXM is slightly different from the Amlogic G12A Glue. The GXL SoCs only embeds 2 USB2 PHYs and no USB3 PHYs, and the GXM SoCs embeds 3 USB2 PHYs. Reviewed-by:
-
Sandeep Maheswaram authored
Add compatible for SC7180 in usb dwc3 bindings. Signed-off-by:
Sandeep Maheswaram <sanm@codeaurora.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Acked-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Signed-off-by:
-
Sandeep Maheswaram authored
Convert USB DWC3 bindings to DT schema format using json-schema. Signed-off-by:
-
Thinh Nguyen authored
The flow from function dwc3_gadget_ep_dequeue() is not easy to follow. Refactor it for easier read. No functional change in this commit. Signed-off-by:
-
Thinh Nguyen authored
Remove 2 unnecessary checks: 1) A request in the started_list must have its trb field set. So checking for req->trb is unnecessary. 2) An endpoint must have started (and have not ended) for the request to still be in the started_list. There's no point to check if the endpoint is started. We had this check because previously the driver didn't handle the endpoint's started/ended flags for END_TRANSFER command properly. See commit 9f45581f ("usb: dwc3: gadget: early giveback if End Transfer already completed"). Signed-off-by:
-
Thinh Nguyen authored
If a request is dequeued, the transfer is cancelled. Give back all the started requests. In most scenarios, the function driver dequeues all requests of a transfer when there's a failure. If the function driver follows this, then it's fine. If not, then we'd be skipping TRBs at different points within the dequeue and enqueue pointers, making dequeue/enqueue pointers useless. To enforce and make sure that we're properly skipping TRBs, cancel all the started requests and give back all the cancelled requests to the function drivers. Signed-off-by:
-
Thinh Nguyen authored
DWC3 must not issue CLEAR_STALL command to control endpoints. The controller automatically clears the STALL when it receives the SETUP token. Also, when the driver receives ClearFeature(halt_ep), DWC3 must stop any active transfer from the endpoint and give back all the requests to the function drivers. Fixes: 72246da4 ("usb: Introduce DesignWare USB3 DRD Driver") Signed-off-by:
-
Tao Ren authored
Update device tree binding document for aspeed vhub's device IDs and string properties. Signed-off-by:
Tao Ren <rentao.bupt@gmail.com> Signed-off-by:
-
Tao Ren authored
This patch moves patch-usb1-dev-desc logic from get-descriptor handler to "ast_vhub_fixup_usb1_dev_desc" function so the code is executed only once (at vhub initial time). Signed-off-by:
-
Tao Ren authored
The patch overrides idVendor, idProduct and bcdDevice fields in vhub Device Descriptor if according device tree properties are defined. Signed-off-by:
-
Tao Ren authored
If "vhub,string-descriptor" device tree property is defined, the driver will load string descriptors from device tree; otherwise, the default string descriptors will be used. Signed-off-by:
-
Tao Ren authored
The USB LANGID validation code in "check_user_usb_string" function is moved to "usb_validate_langid" function which can be used by other usb gadget drivers. Signed-off-by:
-
Tao Ren authored
This patch introduces a link list to store string descriptors with different languages, and "ast_vhub_rep_string" function is also improved to support multiple language usb strings. Signed-off-by:
-
Tao Ren authored
This patch evaluates vhub ports' irq mask before going through per-port irq handling one by one, which helps to speed up irq handling in case there is no port interrupt. Signed-off-by:
-
