- 13 Feb, 2012 1 commit
-
-
NeilBrown authored
Since we added 'replacement' capability, RAID1 can have twice as many devices as ->raid_disks indicates. So md_raid1_congested needs to check that many possible devices, not just ->raid_disks many. Signed-off-by: NeilBrown <neilb@suse.de>
-
- 07 Feb, 2012 1 commit
-
-
NeilBrown authored
1/ If a resync is aborted we should record how far we got (recovery_cp) the last request that we know has completed (->curr_resync_completed) rather than the last request that was submitted (->curr_resync). 2/ When a resync aborts we still want to update the metadata with any changes, so set MD_CHANGE_DEVS even if we 'skip'. Signed-off-by: NeilBrown <neilb@suse.de>
-
- 30 Jan, 2012 1 commit
-
-
Jonathan Brassow authored
The life cycle of a device-mapper target is: 1) create 2) resume 3) suspend *) possibly repeat from 2 4) destroy The dm-raid target is unconditionally calling MD's bitmap_load function upon every resume. If steps 2 & 3 above are repeated, bitmap_load is called multiple times. It is only written to be called once; otherwise, it allocates new memory for the bitmap (without freeing the old) and incrementing the number of pages it thinks it has without zeroing first. This ultimately leads to access beyond allocated memory and lost memory. Simply avoiding the bitmap_load call upon resume is not sufficient. If the target was suspended while the initial recovery was only partially complete, it needs to be restarted when the target is resumed. This is why 'md_wakeup_thread' is called before issuing the 'mddev_resume'. Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
- 10 Jan, 2012 2 commits
-
-
NeilBrown authored
We normally try to avoid reading from write-mostly devices, but when we do we really have to check for bad blocks and be sure not to try reading them. With the current code, best_good_sectors might not get set and that causes zero-length read requests to be send down which is very confusing. This bug was introduced in commit d2eb35ac and so the patch is suitable for 3.1.x and 3.2.x Reported-and-tested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reported-and-tested-by: Art -kwaak- van Breemen <ard@telegraafnet.nl> Signed-off-by: NeilBrown <neilb@suse.de> Cc: stable@vger.kernel.org
-
NeilBrown authored
We currently only 'notify' changes to the 'degraded' attribute when it decreases, not when it increases. Notifying on failure is a little awkward as it happen in interrupt context. So instead, notify when we remove the failed device from the array, which is very soon afterwards. Reported-and-tested-by: Mikhail Balabin <mbalabin@gmail.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
- 22 Dec, 2011 35 commits
-
-
NeilBrown authored
Now that WantReplacement drives are replaced cleanly, mark a drive as want_replacement when we see a write error. It might get failed soon so the WantReplacement flag is irrelevant, but if the write error is recorded in the bad block log, we still want to activate any spare that might be available. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When attempting to add a spare to a RAID1 array, also consider adding it as a replacement for a want_replacement device. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
If a Replacement is seen, file it as such. If we see two replacements (or two normal devices) for the one slot, abort. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When recovery completes ->spare_active is called. This checks if the replacement is ready and if so it fails the original. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
Replacement devices are stored at a different offset, so look there too. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
In RAID1, a replacement is much like a normal device, so we just double the size of the relevant arrays and look at all possible devices for reads and writes. This means that the array looks like it is now double the size in some way - we need to be careful about that. In particular, we checking if the array is still degraded while creating a recovery request we need to only consider the first 'half' - i.e. the real (non-replacement) devices. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
In general mddev->raid_disks can change unexpectedly while conf->raid_disks will only change in a very controlled way. So change some uses of one to the other. The use of mddev->raid_disks will not cause actually problems but this way is more consistent and safer in the long term. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When attempting to add a spare to a RAID10 array, also consider adding it as a replacement for a want_replacement device. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
If a Replacement is seen, file it as such. If we see two replacements (or two normal devices) for the one slot, abort. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When recovery finish and spare_active is called, check for a replace that might have just become fully synced and mark it as such, marking the original as failed. Then when the original is removed, move the replacement into its position. This means that 'replacement' and spontaneously become NULL in some situations. Make sure we check for those. It also means that 'rdev' and 'replacement' could appear to be identical - check for that too. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
If there is a replacement device, then recover to it, reading from any drives - maybe the one being replaced, maybe not. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
If we need to resync an array which has replacement devices, we always write any block checked to every replacement. If the resync was bitmap-based resync we will then complete the replacement normally. If it was a full resync, we mark the replacements as fully recovered when the resync finishes so no further recovery is needed. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When writing, we need to submit two writes, one to the original, and one to the replacements - if there is a replacement. If the write to the replacement results in a write error we just fail the device. We only try to record write errors to the original. This only handles writing new data. Writing for resync/recovery will come later. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
Enhance raid10_remove_disk to be able to remove ->replacement as well as ->rdev Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When reading (for array reads, not for recovery etc) we read from the replacement device if it has recovered far enough. This requires storing the chosen rdev in the 'r10_bio' so we can make sure to drop the ref on the right device when the read finishes. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
It makes more sense to return an rdev than just an index as read_balance() gets a reference to the rdev and so returning the pointer make this more idiomatic. This will be needed in a future patch when we might return a 'replacement' rdev instead of the main rdev. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
Allow each slot in the RAID10 to have 2 devices, the want_replacement and the replacement. Also an r10bio to have 2 bios, and for resync/recovery allocate the second bio if there are any replacement devices. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
Now that WantReplacement drives are replaced cleanly, mark a drive as WantReplacement when we see a write error. It might get failed soon so the WantReplacement flag is irrelevant, but if the write error is recorded in the bad block log, we still want to activate any spare that might be available. Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When attempting to add a spare to a RAID[456] array, also consider adding it as a replacement for a want_replacement device. This requires that common md code attempt hot_add even when the array is not formally degraded. Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
If a Replacement is seen, file it as such. If we see two replacements (or two normal devices) for the one slot, abort. Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When recovery completes - as reported by a call to ->spare_active, we clear In_sync on the original and set it on the replacement. Then when the original gets removed we move the replacement from 'replacement' to 'rdev'. This could race with other code that is looking at these pointers, so we use memory barriers and careful ordering to ensure that a reader might see one device twice, but never no devices. Then the readers guard against using both devices, which could only happen when writing. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
During recovery we want to write to the replacement but not the original. So we have two new flags - R5_NeedReplace if this stripe has a replacement that needs to be written at some stage - R5_WantReplace if NeedReplace, and the data is available, and a 'sync' has been requested on this stripe. We also distinguish between 'sync and replace' which need to read all other devices, and 'replace' which only needs to read the devices being replaced. Note that during resync we always write to any replacement device. It might not need to be written to, but as we don't read to compare, we have to write to be sure. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When writing, we need to submit two writes, one to the original, and one to the replacement - if there is a replacement. If the write to the replacement results in a write error, we just fail the device. We only try to record write errors to the original. When writing for recovery, we shouldn't write to the original. This will be addressed in a subsequent patch that generally addresses recovery. Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
Enhance raid5_remove_disk to be able to remove ->replacement as well as ->rdev. Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
If a replacement device is present and has been recovered far enough, then use it for reading into the stripe cache. If we get an error we don't try to repair it, we just fail the device. A replacement device that gives errors does not sound sensible. This requires removing the setting of R5_ReadError when we get a read error during a read that bypasses the cache. It was probably a bad idea anyway as we don't know that every block in the read caused an error, and it could cause ReadError to be set for the replacement device, which is bad. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
We current initialise some fields of a bio when preparing a stripe_head, and again just before submitting the request. Remove the duplication by only setting the fields that lower level devices don't touch in raid5_build_block, and only set the changeable fields in ops_run_io. Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
Remove some #defines that are no longer used, and replace some others with an enum. And remove an unused field. Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
Just enhance data structures to record a second device per slot to be used as a 'replacement' device, replacing the original. We also have a second bio in each slot in each stripe_head. This will only be used when writing to the array - we need to write to both the original and the replacement at the same time, so will need two bios. For now, only try using the replacement drive for aligned-reads. In this case, we prefer the replacement if it has been recovered far enough, otherwise use the original. This includes a small enhancement. Previously we would only do aligned reads if the target device was fully recovered. Now we also do them if it has recovered far enough. Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
hot-replace is a feature being added to md which will allow a device to be replaced without removing it from the array first. With hot-replace a spare can be activated and recovery can start while the original device is still in place, thus allowing a transition from an unreliable device to a reliable device without leaving the array degraded during the transition. It can also be use when the original device is still reliable but it not wanted for some reason. This will eventually be supported in RAID4/5/6 and RAID10. This patch adds a super-block flag to distinguish the replacement device. If an old kernel sees this flag it will reject the device. It also adds two per-device flags which are viewable and settable via sysfs. "want_replacement" can be set to request that a device be replaced. "replacement" is set to show that this device is replacing another device. The "rd%d" links in /sys/block/mdXx/md only apply to the original device, not the replacement. We currently don't make links for the replacement - there doesn't seem to be a need. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
Soon an array will be able to have multiple devices with the same raid_disk number (an original and a replacement). So removing a device based on the number won't work. So pass the actual device handle instead. Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When setting the slot number on a device in an active array we currently check that the number is not already in use. We then call into the personality's hot_add_disk function which performs the same test and returns the same error. Thus the common test is not needed. As we will shortly be changing some personalities to allow duplicates in some cases (to support hot-replace), the common test will become inconvenient. So remove the common test. Reviewed-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
For each active region corresponding to a bit in the bitmap with have a 14bit counter (and some flags). This counts number of active writes + bit in the on-disk bitmap + delay-needed. The "delay-needed" is because we always want a delay before clearing a bit. So the number here is normally number of active writes plus 2. If there have been no writes for a while, we drop to 1. If still no writes we clear the bit and drop to 0. So for consistency, when setting bit from the on-disk bitmap or by request from user-space it is best to set the counter to '2' to start with. In particular we might also set the NEEDED_MASK flag at this time, and in all other cases NEEDED_MASK is only set when the counter is 2 or more. Signed-off-by: NeilBrown <neilb@suse.de>
-
Steven Rostedt authored
While using etags to find free_pages(), I stumbled across this debug definition of free_pages() that is to be used while debugging some raid code in userspace. The __get_free_pages() allocates the correct size, but the free_pages() does not match. free_pages(), like __get_free_pages(), takes an order and not a size. Acked-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
When an array is being reshaped to change the number of devices, the two halves can be differently degraded. e.g. one could be missing a device and the other not. So we need to be more careful about calculating the 'degraded' attribute. Instead of just inc/dec at appropriate times, perform a full re-calculation examining both possible cases. This doesn't happen often so it not a big cost, and we already have most of the code to do it. Signed-off-by: NeilBrown <neilb@suse.de>
-
NeilBrown authored
We have a variable 'mddev' in this function, but repeatedly get the same value by dereferencing bitmap->mddev. There is room for simplification here... Signed-off-by: NeilBrown <neilb@suse.de>
-