commit 50e95b6b ("ARM: dts: am57xx-idk: Add Industrial
output support") added the TPIC2810 device-tree node under
SPI bus instead of I2C1.

Fix it. Tested on AM572x IDK by driving on-board LEDs
connected to TPIC2810

Fixes: 50e95b6b ("ARM: dts: am57xx-idk: Add Industrial output support")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

What happens is that a write to /dev/sg is given a request with non-zero
->iovec_count combined with zero ->dxfer_len.  Or with ->dxferp pointing
to an array full of empty iovecs.

Having write permission to /dev/sg shouldn't be equivalent to the
ability to trigger BUG_ON() while holding spinlocks...

Found by Dmitry Vyukov and syzkaller.

[ The BUG_ON() got changed to a WARN_ON_ONCE(), but this fixes the
  underlying issue.  - Linus ]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Don't crash the machine just because of an empty transfer. Use WARN_ON()
combined with returning an error.

Found by Dmitry Vyukov and syzkaller.

[ Changed to "WARN_ON_ONCE()". Al has a patch that should fix the root
  cause, but a BUG_ON() is not acceptable in any case, and a WARN_ON()
  might still be a cause of excessive log spamming.

  NOTE! If this warning ever triggers, we may end up leaking resources,
  since this doesn't bother to try to clean the command up. So this
  WARN_ON_ONCE() triggering does imply real problems. But BUG_ON() is
  much worse.

  People really need to stop using BUG_ON() for "this shouldn't ever
  happen". It makes pretty much any bug worse.     - Linus ]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If ip6_dst_lookup_tail has acquired a dst and fails the IPv4-mapped
check, release the dst before returning an error.

Fixes: ec5e3b0a ("ipv6: Inhibit IPv4-mapped src address on the wire.")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ARM SoC fixes from Arnd Bergmann:
 "Two more bugfixes that came in during this week:

   - a defconfig change to enable a vital driver used on some Qualcomm
     based phones. This was already queued for 4.11, but the maintainer
     asked to have it in 4.10 after all.

   - a regression fix for the reset controller framework, this got
     broken by a typo in the 4.10 merge window"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: multi_v7_defconfig: enable Qualcomm RPMCC
  reset: fix shared reset triggered_count decrement on error

Pull ARM fixes from Russell King:
 "A couple of fixes from Kees concerning problems he spotted with our
  user access support"

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 8658/1: uaccess: fix zeroing of 64-bit get_user()
  ARM: 8657/1: uaccess: consistently check object sizes

Pull x86 fix from Thomas Gleixner:
 "Make the build clean by working around yet another GCC stupidity"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vm86: Fix unused variable warning if THP is disabled

Pull locking fix from Thomas Gleixner:
 "Move the futex init function to core initcall so user mode helper does
  not run into an uninitialized futex syscall"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex: Move futex_init() to core_initcall

Pull timer fixes from Thomas Gleixner:
 "Two small fixes::

   - Prevent deadlock on the tick broadcast lock. Found and fixed by
     Mike.

   - Stop using printk() in the timekeeping debug code to prevent a
     deadlock against the scheduler"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Use deferred printk() in debug code
  tick/broadcast: Prevent deadlock on tick_broadcast_lock

Pull networking fixes from David Miller:

 1) Fix leak in dpaa_eth error paths, from Dan Carpenter.

 2) Use after free when using IPV6_RECVPKTINFO, from Andrey Konovalov.

 3) fanout_release() cannot be invoked from atomic contexts, from Anoob
    Soman.

 4) Fix bogus attempt at lockdep annotation in IRDA.

 5) dev_fill_metadata_dst() can OOP on a NULL dst cache pointer, from
    Paolo Abeni.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  irda: Fix lockdep annotations in hashbin_delete().
  vxlan: fix oops in dev_fill_metadata_dst
  dccp: fix freeing skb too early for IPV6_RECVPKTINFO
  dpaa_eth: small leak on error
  packet: Do not call fanout_release from atomic contexts

Use rcuidle console tracepoint because, apparently, it may be issued
from an idle CPU:

  hw-breakpoint: Failed to enable monitor mode on CPU 0.
  hw-breakpoint: CPU 0 failed to disable vector catch

  ===============================
  [ ERR: suspicious RCU usage.  ]
  4.10.0-rc8-next-20170215+ #119 Not tainted
  -------------------------------
  ./include/trace/events/printk.h:32 suspicious rcu_dereference_check() usage!

  other info that might help us debug this:

  RCU used illegally from idle CPU!
  rcu_scheduler_active = 2, debug_locks = 0
  RCU used illegally from extended quiescent state!
  2 locks held by swapper/0/0:
   #0:  (cpu_pm_notifier_lock){......}, at: [<c0237e2c>] cpu_pm_exit+0x10/0x54
   #1:  (console_lock){+.+.+.}, at: [<c01ab350>] vprintk_emit+0x264/0x474

  stack backtrace:
  CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc8-next-20170215+ #119
  Hardware name: Generic OMAP4 (Flattened Device Tree)
    console_unlock
    vprintk_emit
    vprintk_default
    printk
    reset_ctrl_regs
    dbg_cpu_pm_notify
    notifier_call_chain
    cpu_pm_exit
    omap_enter_idle_coupled
    cpuidle_enter_state
    cpuidle_enter_state_coupled
    do_idle
    cpu_startup_entry
    start_kernel

This RCU warning, however, is suppressed by lockdep_off() in printk().
lockdep_off() increments the ->lockdep_recursion counter and thus
disables RCU_LOCKDEP_WARN() and debug_lockdep_rcu_enabled(), which want
lockdep to be enabled "current->lockdep_recursion == 0".

Link: http://lkml.kernel.org/r/20170217015932.11898-1-sergey.senozhatsky@gmail.comSigned-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <rmk@armlinux.org.uk>
Cc: <stable@vger.kernel.org> [3.4+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch enables the Qualcomm RPM based Clock Controller present on
A-family boards.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

A nested lock depth was added to the hasbin_delete() code but it
doesn't actually work some well and results in tons of lockdep splats.

Fix the code instead to properly drop the lock around the operation
and just keep peeking the head of the hashbin queue.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull block layer fix from Jens Axboe:
 "A single fix for a lockdep splat reported by Thomas and Gabriel"

* 'for-linus' of git://git.kernel.dk/linux-block:
  cfq-iosched: don't call wbt_disable_default() with IRQs disabled

Since the commit 0c1d70af ("net: use dst_cache for vxlan device")
vxlan_fill_metadata_dst() calls vxlan_get_route() passing a NULL
dst_cache pointer, so the latter should explicitly check for
valid dst_cache ptr. Unfortunately the commit d71785ff ("net: add
dst_cache to ovs vxlan lwtunnel") removed said check.

As a result is possible to trigger a null pointer access calling
vxlan_fill_metadata_dst(), e.g. with:

ovs-vsctl add-br ovs-br0
ovs-vsctl add-port ovs-br0 vxlan0 -- set interface vxlan0 \
	type=vxlan options:remote_ip=192.168.1.1 \
	options:key=1234 options:dst_port=4789 ofport_request=10
ip address add dev ovs-br0 172.16.1.2/24
ovs-vsctl set Bridge ovs-br0 ipfix=@i -- --id=@i create IPFIX \
	targets=\"172.16.1.1:1234\" sampling=1
iperf -c 172.16.1.1 -u -l 1000 -b 10M -t 1 -p 1234

This commit addresses the issue passing to vxlan_get_route() the
dst_cache already available into the lwt info processed by
vxlan_fill_metadata_dst().

Fixes: d71785ff ("net: add dst_cache to ovs vxlan lwtunnel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current DCCP implementation an skb for a DCCP_PKT_REQUEST packet
is forcibly freed via __kfree_skb in dccp_rcv_state_process if
dccp_v6_conn_request successfully returns.

However, if IPV6_RECVPKTINFO is set on a socket, the address of the skb
is saved to ireq->pktopts and the ref count for skb is incremented in
dccp_v6_conn_request, so skb is still in use. Nevertheless, it gets freed
in dccp_rcv_state_process.

Fix by calling consume_skb instead of doing goto discard and therefore
calling __kfree_skb.

Similar fixes for TCP:

fb7e2399 [TCP]: skb is unexpectedly freed.
0aea76d3 tcp: SYN packets are now
simply consumed
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull powerpc fix from Michael Ellerman:
 "One fix from Paul: we can not use the radix MMU under a hypervisor for
  now.

  Although the code checked if the processor supports radix, that is not
  sufficient"

* tag 'powerpc-4.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64: Disable use of radix under a hypervisor

Pull input fix from Dmitry Torokhov:
 "Just a single change to Elan touchpad driver to recognize a new ACPI
  ID"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elan_i2c - add ELAN0605 to the ACPI table

Pull i2c fix from Wolfram Sang:
 "I2C has a revert to fix a regression"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  Revert "i2c: designware: detect when dynamic tar update is possible"

Pull MMC fix from Ulf Hansson:
 "Fix multi-bit bus width without high-speed mode for MMC"

* tag 'mmc-v4.10-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: core: fix multi-bit bus width without high-speed mode

Pull NTB bugfixes frfom Jon Mason:
 "NTB bug fixes to address a crash when unloading the ntb module, a DMA
  engine unmap leak, allowing the proper queue choice, and clearing the
  SKX irq bit"

* tag 'ntb-4.10-bugfixes' of git://github.com/jonmason/ntb:
  ntb: ntb_hw_intel: link_poll isn't clearing the pending status properly
  ntb_transport: Pick an unused queue
  ntb: ntb_perf missing dmaengine_unmap_put
  NTB: ntb_transport: fix debugfs_remove_recursive

This should be >= instead of > here.  It means that we don't increment
the free count enough so it becomes off by one.

Fixes: 9ad1a374 ("dpaa_eth: add support for DPAA Ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull "Reset controller fixes for v4.10" from Philipp Zabel:

- Remove erroneous negation of the error check of the reset function
  to decrement trigger_count in the error case, not on success. This
  fixes shared resets to actually only trigger once, as intended.

* tag 'reset-for-4.10-fixes' of https://git.pengutronix.de/git/pza/linux:
  reset: fix shared reset triggered_count decrement on error

Commit 66644982 ("packet: call fanout_release, while UNREGISTERING a
netdev"), unfortunately, introduced the following issues.

1. calling mutex_lock(&fanout_mutex) (fanout_release()) from inside
rcu_read-side critical section. rcu_read_lock disables preemption, most often,
which prohibits calling sleeping functions.

[  ] include/linux/rcupdate.h:560 Illegal context switch in RCU read-side critical section!
[  ]
[  ] rcu_scheduler_active = 1, debug_locks = 0
[  ] 4 locks held by ovs-vswitchd/1969:
[  ]  #0:  (cb_lock){++++++}, at: [<ffffffff8158a6c9>] genl_rcv+0x19/0x40
[  ]  #1:  (ovs_mutex){+.+.+.}, at: [<ffffffffa04878ca>] ovs_vport_cmd_del+0x4a/0x100 [openvswitch]
[  ]  #2:  (rtnl_mutex){+.+.+.}, at: [<ffffffff81564157>] rtnl_lock+0x17/0x20
[  ]  #3:  (rcu_read_lock){......}, at: [<ffffffff81614165>] packet_notifier+0x5/0x3f0
[  ]
[  ] Call Trace:
[  ]  [<ffffffff813770c1>] dump_stack+0x85/0xc4
[  ]  [<ffffffff810c9077>] lockdep_rcu_suspicious+0x107/0x110
[  ]  [<ffffffff810a2da7>] ___might_sleep+0x57/0x210
[  ]  [<ffffffff810a2fd0>] __might_sleep+0x70/0x90
[  ]  [<ffffffff8162e80c>] mutex_lock_nested+0x3c/0x3a0
[  ]  [<ffffffff810de93f>] ? vprintk_default+0x1f/0x30
[  ]  [<ffffffff81186e88>] ? printk+0x4d/0x4f
[  ]  [<ffffffff816106dd>] fanout_release+0x1d/0xe0
[  ]  [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0

2. calling mutex_lock(&fanout_mutex) inside spin_lock(&po->bind_lock).
"sleeping function called from invalid context"

[  ] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620
[  ] in_atomic(): 1, irqs_disabled(): 0, pid: 1969, name: ovs-vswitchd
[  ] INFO: lockdep is turned off.
[  ] Call Trace:
[  ]  [<ffffffff813770c1>] dump_stack+0x85/0xc4
[  ]  [<ffffffff810a2f52>] ___might_sleep+0x202/0x210
[  ]  [<ffffffff810a2fd0>] __might_sleep+0x70/0x90
[  ]  [<ffffffff8162e80c>] mutex_lock_nested+0x3c/0x3a0
[  ]  [<ffffffff816106dd>] fanout_release+0x1d/0xe0
[  ]  [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0

3. calling dev_remove_pack(&fanout->prot_hook), from inside
spin_lock(&po->bind_lock) or rcu_read-side critical-section. dev_remove_pack()
-> synchronize_net(), which might sleep.

[  ] BUG: scheduling while atomic: ovs-vswitchd/1969/0x00000002
[  ] INFO: lockdep is turned off.
[  ] Call Trace:
[  ]  [<ffffffff813770c1>] dump_stack+0x85/0xc4
[  ]  [<ffffffff81186274>] __schedule_bug+0x64/0x73
[  ]  [<ffffffff8162b8cb>] __schedule+0x6b/0xd10
[  ]  [<ffffffff8162c5db>] schedule+0x6b/0x80
[  ]  [<ffffffff81630b1d>] schedule_timeout+0x38d/0x410
[  ]  [<ffffffff810ea3fd>] synchronize_sched_expedited+0x53d/0x810
[  ]  [<ffffffff810ea6de>] synchronize_rcu_expedited+0xe/0x10
[  ]  [<ffffffff8154eab5>] synchronize_net+0x35/0x50
[  ]  [<ffffffff8154eae3>] dev_remove_pack+0x13/0x20
[  ]  [<ffffffff8161077e>] fanout_release+0xbe/0xe0
[  ]  [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0

4. fanout_release() races with calls from different CPU.

To fix the above problems, remove the call to fanout_release() under
rcu_read_lock(). Instead, call __dev_remove_pack(&fanout->prot_hook) and
netdev_run_todo will be happy that &dev->ptype_specific list is empty. In order
to achieve this, I moved dev_{add,remove}_pack() out of fanout_{add,release} to
__fanout_{link,unlink}. So, call to {,__}unregister_prot_hook() will make sure
fanout->prot_hook is removed as well.

Fixes: 66644982 ("packet: call fanout_release, while UNREGISTERING a netdev")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Anoob Soman <anoob.soman@citrix.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For a shared reset, when the reset is successful, the triggered_count is
incremented when trying to call the reset callback, so that another device
sharing the same reset line won't trigger it again. If the reset has not
been triggered successfully, the trigger_count should be decremented.

The code does the opposite, and decrements the trigger_count on success.
As a consequence, another device sharing the reset will be able to trigger
it again.

Fixed be removing negation in from of the error code of the reset function.

Fixes: 7da33a37 ("reset: allow using reset_control_reset with shared reset")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

On Skylake hardware, the link_poll isn't clearing the pending interrupt
bit.  Adding a new function for SKX that handles clearing of status bit the
right way.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 783dfa6c ("ntb: Adding Skylake Xeon NTB support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Fix typo causing ntb_transport_create_queue to select the first
queue every time, instead of using the next free queue.
Signed-off-by: Thomas VanSelus <tvanselus@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Fixes: fce8a7bb ("PCI-Express Non-Transparent Bridge Support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>

In the normal I/O execution path, ntb_perf is missing a call to
dmaengine_unmap_put() after submission. That causes us to leak
unmap objects.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 8a7b6a77 ("ntb: ntb perf tool")
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The call to debugfs_remove_recursive(qp->debugfs_dir) of the sub-level
directory must not be later than
debugfs_remove_recursive(nt_debugfs_dir) of the top-level directory.
Otherwise, the sub-level directory will not exist, and it would be
invalid (panic) to attempt to remove it.  This removes the top-level
directory last, after sub-level directories have been cleaned up.
Signed-off-by: Allen Hubbe <Allen.Hubbe@dell.com>
Fixes: e26a5843 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Pull drm fixes from Dave Airlie:
 "Just two last minute fixes, one for DP MST oopses and one for a radeon
  regression"

* tag 'drm-fixes-for-v4.10-final' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: Use mode h/vdisplay fields to hide out of bounds HW cursor
  drm/dp/mst: fix kernel oops when turning off secondary monitor

One regression fix for interlaced modes on radeon

* 'drm-fixes-4.10' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: Use mode h/vdisplay fields to hide out of bounds HW cursor

'adr' yields a data-pointer, not a function-pointer.

Fixes: 999f934d ("ARM: omap5/dra7xx: Enable booting secondary
CPU in HYP mode")
Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This reverts commit 24b91e36 and commit
7bdb59f1 ("tick/nohz: Fix possible missing clock reprog after tick
soft restart") that depends on it,

Pavel reports that it causes occasional boot hangs for him that seem to
depend on just how the machine was booted.  In particular, his machine
hangs at around the PCI fixups of the EHCI USB host controller, but only
hangs from cold boot, not from a warm boot.

Thomas Gleixner suspecs it's a CPU hotplug interaction, particularly
since Pavel also saw suspend/resume issues that seem to be related.
We're reverting for now while trying to figure out the root cause.
Reported-bisected-and-tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org  # reverted commits were marked for stable
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull media fix from Mauro Carvalho Chehab:
 "A regression fix that makes the Siano driver to work again after the
  CONFIG_VMAP_STACK change"

* tag 'media/v4.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] siano: make it work again with CONFIG_VMAP_STACK

Flags (PIPE_BUF_FLAG_PACKET, PIPE_BUF_FLAG_GIFT) could remain on the
unused part of the pipe ring buffer.  Previously splice_to_pipe() left
the flags value alone, which could result in incorrect behavior.

Uninitialized flags appears to have been there from the introduction of
the splice syscall.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Cc: <stable@vger.kernel.org> # 2.6.17+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull fuse fixes from Miklos Szeredi:
 "Fix a use after free bug introduced in 4.2 and using an uninitialized
  value introduced in 4.9"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: fix uninitialized flags in pipe_buffer
  fuse: fix use after free issue in fuse_dev_do_read()

Pull PCI fix from Bjorn Helgaas:
 "Add back pcie_pme_remove() so we free the IRQ when removing PCIe port
  devices; previously the leaked IRQ caused an MSI BUG_ON"

* tag 'pci-v4.10-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI/PME: Restore pcie_pme_driver.remove

Pull networking fixes from David Miller:

 1) In order to avoid problems in the future, make cgroup bpf overriding
    explicit using BPF_F_ALLOW_OVERRIDE. From Alexei Staovoitov.

 2) LLC sets skb->sk without proper skb->destructor and this explodes,
    fix from Eric Dumazet.

 3) Make sure when we have an ipv4 mapped source address, the
    destination is either also an ipv4 mapped address or
    ipv6_addr_any(). Fix from Jonathan T. Leighton.

 4) Avoid packet loss in fec driver by programming the multicast filter
    more intelligently. From Rui Sousa.

 5) Handle multiple threads invoking fanout_add(), fix from Eric
    Dumazet.

 6) Since we can invoke the TCP input path in process context, without
    BH being disabled, we have to accomodate that in the locking of the
    TCP probe. Also from Eric Dumazet.

 7) Fix erroneous emission of NETEVENT_DELAY_PROBE_TIME_UPDATE when we
    aren't even updating that sysctl value. From Marcus Huewe.

 8) Fix endian bugs in ibmvnic driver, from Thomas Falcon.

[ This is the second version of the pull that reverts the nested
  rhashtable changes that looked a bit too scary for this late in the
  release  - Linus ]

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
  rhashtable: Revert nested table changes.
  ibmvnic: Fix endian errors in error reporting output
  ibmvnic: Fix endian error when requesting device capabilities
  net: neigh: Fix netevent NETEVENT_DELAY_PROBE_TIME_UPDATE notification
  net: xilinx_emaclite: fix freezes due to unordered I/O
  net: xilinx_emaclite: fix receive buffer overflow
  bpf: kernel header files need to be copied into the tools directory
  tcp: tcp_probe: use spin_lock_bh()
  uapi: fix linux/if_pppol2tp.h userspace compilation errors
  packet: fix races in fanout_add()
  ibmvnic: Fix initial MTU settings
  net: ethernet: ti: cpsw: fix cpsw assignment in resume
  kcm: fix a null pointer dereference in kcm_sendmsg()
  net: fec: fix multicast filtering hardware setup
  ipv6: Handle IPv4-mapped src to in6addr_any dst.
  ipv6: Inhibit IPv4-mapped src address on the wire.
  net/mlx5e: Disable preemption when doing TC statistics upcall
  rhashtable: Add nested tables
  tipc: Fix tipc_sk_reinit race conditions
  gfs2: Use rhashtable walk interface in glock_hash_walk
  ...