- 18 Dec, 2013 40 commits
-
-
Sujith Manoharan authored
The interrupt reference counter is always initialized in ath9k_start(). Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Sujith Manoharan authored
* Remove unused macros. * Move definitions to appropriate sections. Signed-off-by:
-
Sujith Manoharan authored
* Move definitions to spectral.h * Move processing/debug code to spectral.c Signed-off-by:
-
Luis R. Rodriguez authored
I've thrown the towel at QCA. Signed-off-by:
Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by:
-
Felix Fietkau authored
The beacon code previously reset TSF on every configuration call, as some of the code was not prepared to properly calculate nexttbtt based on current TSF. This patch adds a common function for calculating nexttbtt and moves the TSF reset to driver start. This should improve AP mode compatibility with various stations that expect the TSF to not randomly jump due to hardware resets. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
Remove unused fields, pass timer info in usec instead of TU. Preparation for fixing nexttbtt calculation Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
It is unused Signed-off-by:
-
Felix Fietkau authored
Remove ah->config.spurmode and ah->config.spurchans, always use EEPROM data. Signed-off-by:
-
Felix Fietkau authored
It is unused Signed-off-by:
-
Felix Fietkau authored
The hardware does not have support for ATIM processing, and the driver does not set up ah->atim_window anywhere. Additionally, the code can clobber the timer used by P2P powersave. Signed-off-by:
-
Felix Fietkau authored
- Use generic bitops instead of custom hackery - Move interrupt enable/disable logic from ath9k to ath9k_hw - Decouple ISR call from btcoex - Make the overflow callback optional (to prevent IRQ storms) Signed-off-by:
-
Felix Fietkau authored
TSF accuracy is not needed here, and there is only one usable generic timer that is supported by all chips and uses the primary TSF counter. Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
-
Felix Fietkau authored
There's no need to truncate curchan->hw_value to u8 Signed-off-by:
-
Rashika Kheria authored
This patch marks the function il_clear_traffic_stats() in debug.c as static because they are not used outside this file. Thus, it also removes the following warnings in wireless/iwlegacy/debug.c: drivers/net/wireless/iwlegacy/debug.c:35:1: warning: no previous prototype for ‘il_clear_traffic_stats’ [-Wmissing-prototypes] Signed-off-by:
Rashika Kheria <rashika.kheria@gmail.com> Reviewed-by:
Josh Triplett <josh@joshtriplett.org> Signed-off-by:
-
Rashika Kheria authored
This patch marks the function il4965_ucode_rx_stats_read(), il4965_ucode_tx_stats_read() and il4965_ucode_general_stats_read() in 4965-debug.c as static because they are not used outside this file. Thus, it also removes the following warnings in wireless/iwlegacy/4965-debug.c: drivers/net/wireless/iwlegacy/4965-debug.c:59:1: warning: no previous prototype for ‘il4965_ucode_rx_stats_read’ [-Wmissing-prototypes] drivers/net/wireless/iwlegacy/4965-debug.c:471:1: warning: no previous prototype for ‘il4965_ucode_tx_stats_read’ [-Wmissing-prototypes] drivers/net/wireless/iwlegacy/4965-debug.c:637:1: warning: no previous prototype for ‘il4965_ucode_general_stats_read’ [-Wmissing-prototypes] Signed-off-by:
-
Rashika Kheria authored
This patch marks the function il3945_ucode_rx_stats_read(), il3945_ucode_tx_stats_read() and il3945_ucode_general_stats_read() in 3945-debug.c as static because they are not used outside this file. Thus, it also removes the following warnings in wireless/iwlegacy/3945-debug.c: drivers/net/wireless/iwlegacy/3945-debug.c:52:1: warning: no previous prototype for ‘il3945_ucode_rx_stats_read’ [-Wmissing-prototypes] drivers/net/wireless/iwlegacy/3945-debug.c:317:1: warning: no previous prototype for ‘il3945_ucode_tx_stats_read’ [-Wmissing-prototypes] drivers/net/wireless/iwlegacy/3945-debug.c:407:1: warning: no previous prototype for ‘il3945_ucode_general_stats_read’ [-Wmissing-prototypes] Signed-off-by:
-
Bing Zhao authored
When driver gets regulatory domain change notifications or before associates to an AP with Country IE, the txpwrlimit table stored in device tree for that country is downloaded to firmware. The txpwrlimit downloading will happen only at the first time when the alpha2 country code is changed. World regulatory domain "00" notification doesn't trigger the downloading. This behavior is same as domain_info command. Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Bing Zhao authored
Currently only conf file based cal-data downloading is supported. On embedded platforms a better place to store the cal-data is in device tree. Add cal-data downloading from device tree to firmware. Both methods can co-exist. Signed-off-by:
-
Bing Zhao authored
The cfg_data buffer will include the cfg_data structure header (action, type, data_len). This makes it work for all data types without extra parsing. Signed-off-by:
-
Bing Zhao authored
On cfg80211 regulatory domain change, drivers gets alpha2 country code or "00" in driver's notification handler. In most cases, the pattern will be US, 00, US, 00, US, 00, US, ... There is no need to send domain info to firmware in case of "00" or with the same alpha2 country code. Signed-off-by:
-
Lorenzo Bianconi authored
Move ath9k_hw_set_rfmode() after ath9k_hw_process_ini() in order to avoid AR_PHY_MODE register is overwritten with default values by ar9003_hw_process_ini() Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Signed-off-by:
-
Oleksij Rempel authored
On suspend/resume, firmware will restart and gpios configuration will be reseted. Restore this configureation at least for LEDs Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Signed-off-by:
-
Arend van Spriel authored
The struct brcmf_sdio_dev contains array of sdio functions that are used in the driver. However, during probe func[0] entry was assigned to the function 1 reference. This was corrected upon doing the actual I/O access. This patch makes it more clear by creating the func[0] entry properly and use it as is during I/O access. Reviewed-by:
Franky Lin <frankyl@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
Instead of calling brcmf_sdio_disconnect() expose brcmf_sdio_remove() and call it directly. Reviewed-by:
-
Arend van Spriel authored
Functions in dhd_sdio.c that are called with struct brcmf_sdio instance are renamed consistently with brcmf_sdio_ prefix. Reviewed-by:
-
Hante Meuleman authored
For the transmission of data a protocol push hdr is performed followed by a bus txdata call. For the new protocol msgbuf this is not workable. Since they are already "loosely" coupled for bcdc protocol they are combined. This means that txdata will go "through" the protocol layer and a seperate protocol push hdr will not be needed anymore. Reviewed-by:
-
Hante Meuleman authored
A new protocol layer msgbuf will be added in the future. This change makes it possible to select the desired layer by the bus driver. USB and SDIO will select BCDC. At the moment nothing is being done with this information. Reviewed-by:
-
Hante Meuleman authored
The debug function brcmf_dbg_hex_dump API got changed and the information string should preferably contain a \n at the end of the string. Update the FWIL so debug output looks better. Reviewed-by:
-
Hante Meuleman authored
The BCDC functions query_dcmd and set_dcmd both create a msgbuf to be sent to dongle this code is very similar and for optimisation best put in a function. Reviewed-by:
-
Arend van Spriel authored
The SDIO send and receive functions in bcmsdh.c are always called with the same parameters. For the driver there is no use-case to call them otherwise so remove those parameters from function prototypes. Reviewed-by:
-
Arend van Spriel authored
Functions in bcmsdh.c that are called with struct brcmf_sdio_dev instance are renamed consistently with brcmf_sdiod_ prefix. Also removing brcmf_sdioh_attach/detach() functions and merge it with brcmf_sdiod_probe/remove(). Reviewed-by:
-
Arend van Spriel authored
Instead of using the brcmf_sdio_wdtimer_enable() function call brcmf_sdbrcm_wd_timer() directly. Reviewed-by:
-
Arend van Spriel authored
In sdio code a couple of functions use a void pointer as argument type although it should be struct brcmf_sdio. Changing the functions to have proper type checking. Reviewed-by:
-
Arend van Spriel authored
The chip recognition requires a base address that was provided to it during the probe. However, the address is a fixed define value so it is unnecessary to pass through the probe functions. Reviewed-by:
-
Arend van Spriel authored
Make brcmf_sdio_regrw_helper() static removing its use outside of the bcmsdh.c source file. Reviewed-by:
-
Arend van Spriel authored
Instead of catching CCCR_IOEx register in F0 write access to determine whether F2 state needs to change do it with direct call to sdio_[enable/disable]_func(). Reviewed-by:
-
Arend van Spriel authored
During the SDIO probe the func_cis_ptr attribute in struct brcmf_sdio_dev is being determined, but it is never used after that. Removing it also obsoletes two functions in bcmsdh.c. Reviewed-by:
-
Arend van Spriel authored
With the merge of bcmsdh.c and bcmsdh_mmc.c several function prototypes are no longer necessary and can be removed. Consequence is reordering some of the functions. Reviewed-by:
-
