When a STA sends huge BK QoS data frame first and then sends BE/VI/VO
QoS data frame, the corresponding throughput becomes much lower than
that without sends BK QoS data frame before.

The root cause is that when station send BK stream, the tx credits of
BK stream don't return back to higher priority QoS stream such as BE,
VI, and VO stream. This patch will handle BK stream properly, when
there is higher priority QoS stream, it will seek tx credits from BK
stream properly.
Signed-off-by: Kevin Fang <kevin.fang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

bss filter is configured to allow the frames from all the bss other
than the currenly connected one, this is done when a scan is requested
in connected state. There is no reason to filter out the currently
connected bss, configure the filter to allow all the bss. This would
fix the reporting of stale rssi of the current bss while scanning.
Reported-by: Naveen singh <navesing@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

With firmwares which do not support rsn capability override
(ATH6KL_FW_CAPABILITY_RSN_CAP_OVERRIDE) from host would
cause 4-way handshake failure when HT cap is advertised.
To fix this, do not advertise HT cap with cfg80211 for
those fw.

kvalo: fix a checkpatch warning
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This patch enables all multicast packets in non suspend mode
and enable multicast filtering in wow suspend mode. This also
fixes a bug in multicast where the driver assumed disable
multicast-all command disabled/filtered all multicast
packets, which was wrong assumption, because firmware will
apply the programmed filter.

Multicast requirements
 - Enable forward all multicast packets(no filtering) in
      non suspend mode.
 - Enable multicast filtering in wow suspend mode for both
      AP and CLIENT.

kvalo: fix a checkpatch warning and drop unrelated newline removal
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The patch "ath6kl: support fw reporting phy capabilities" gave the
firmware the ability to disable certain wiphy supported bands. Check if
this is the case in ath6kl_wmi_beginscan_cmd to avoid dereferencing a
NULL pointer.

kvalo: change the patch so that there's no code between declarations
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Do not assume anyone before us includes it for us.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Complete the waiting fwlog_block_read on debugfs cleanup, otherwise
userspace and module unload might softlock.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is supposed to be pushed in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The original conditions are always true.  I think && was intended here,
but I don't have the hardware to test.  Could you take a look?

kvalo: Chilam confirmed that the fix is valid
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The ath6kl fw does not have enough memory to support the WoW filters of
more than one vif. Disallow WoW suspend if this is the case.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Now that we know the supported PHY capabilities, only restore supported
bands / HT capabilities in firmware when stopping AP.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Currently the supported bands are just hard coded in the driver.
However, the ath6kl FW will include its 11n and band capabilites in a
WMI_READY event. Handle this and report capabilites to cfg80211
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl: If wow deepsleep pno suspend failure driver will choose cutpower.
in this scenario MMC_PM_KEEP_POWER should be cleared so that mmc will power
off the ar6000

kvalo: remove extra parenthesis
Signed-off-by: Ming Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Set max_scan_ssids and max_sched_scan_ssids to same value. These use the
same probed SSID list, so there is no point in using different maximum
number of SSIDs.

Clear probed SSID entries that are not used. This was already done for
sched_scan, but not for scan. Be consistent and clear the table for both
cases to avoid leaving bogus entries.

In addition, share the same function for setting the probed SSIDs for
scan and sched_scan paths. This fixes setting of wildcard SSID flag
(ANY_SSID_FLAG) and changes the scan path to use probed SSID index
consistently (i.e., start with 0 similarly to sched_scan; firmware
will handle the needed internal mapping).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl does not support Probe Response offloading for Interworking (IEEE
802.11u), so remove the incorrectly added capability flag for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Background scan interval should not be modified while starting
schedule scanning as it changes the bg scan interval when connected to AP.
Use the currently configured interval instead.

kvalo: improve commit log
Signed-off-by: Subramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Added a new member bg_scan_period in struct ath6kl_vif
to retain background scan period value configured via debugfs
entry 'bgscan_interval'. This backup is needed in schedule scan
path while configuring scan parameters.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

We can remove the NULL check here.  It triggers a Smatch warning because
list_first_entry() never is NULL and people who check for it normally
intend to check for list_empty() instead.  In these cases however,
we've already verified that the lists are not empty.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

kvalo: do the same changes for ar6004 hw1.2 as well

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Aafter wlan interface is down WLAN_ENABLED flags will be cleared and
deepsleep_suspend function will be blocked in this senario. This patch
allows deepsleep_suspend function when wlan interface down by removed
the WLAN_ENABLED flag checking.

kvalo: fix commit log
Signed-off-by: Ming Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

System crash because of NULL pointer reference due to
cleanup_scatter is not implemented for USB.
Signed-off-by: Ray Chen <raychen@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Found by checkpatch:

WARNING: quoted string split across lines
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If, in
drivers/net/wireless/ath/ath6kl/debug.c::ath6kl_fwlog_block_read(),
the call to wait_for_completion_interruptible() returns -ERESTARTSYS
then we'll return without freeing the (as yet unused) memory we
allocated for 'buf' - thus leaking it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add the necessary change for AR6004 1.2 chip support
Signed-off-by: Ray Chen <raychen@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Currently rsn capability is not set when it is not available in
rsn IE. Set it to 0 in firmware when it is not there in the ie to
make sure host and target are consistent.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

alignment is not taken care in accessing pairwise cipher and AKM suite
count which are parsed from rsn ie. Fix this alignment issue.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If an ath6kl AP vif is beaconing on one channel, and a STA vif
associates on a different channel, a WMI_DISCONNECT event will be sent
to the AP vif. Make the AP vif follow the STA interface, and notify
userspace.

kvalo: fix a sparse warning with vif->next_chan
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is workaround H/W or F/W bug, see in code comments. Without the fix
ping can receive duplicated ICMP frames while associated with legacy AP.
Reported-by: Walter Goldens <goldenstranger@yahoo.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Driver does not use it any more.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

and all referenced structs and corresponding enums because the driver
does not use it.

Note: keep libipw_info_element struct since it is still in use.
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The firmware may decide to switch channels while already beaconing, e.g.
in response to a cfg80211 connect request on a different vif. Add this
event to notify userspace when an AP or GO interface has successfully
migrated to a new channel, so it can update its configuration
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Remove extraneous statements from ath5k_hw_proc_4word_tx_status and ath5k_hw_proc_2word_status.
Signed-off-by: Qasim Javed <qasimj@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In WoWLAN, we only get the triggers when we actually get
to suspend. As a consequence, drivers currently don't
know that the device should enable wakeup. However, the
device_set_wakeup_enable() API is intended to be called
when the wakeup is enabled, not later when needed.

Add a new set_wakeup() call to cfg80211 and mac80211 to
allow drivers to properly call device_set_wakeup_enable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Semicolons are not necessary after macros that end in while (0).
Remove them.

Simplify the macros with tests of
do { if (foo>size) memset1; else memset2;} while (0);
to a single line memset(,,min_t(size_t, foo, size))
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds counters in various places that can drop packets on
rx without otherwise incrementing a counter.  It also counts
some non-error cases, such as becons and fragments received.

Should help with figuring out where packets are (and are not)
dropped.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This counts any failure during getting packets into
the DMA buffers, including out-of-memory, etc.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Follow updates in DFS pattern detector interface:
a) use given pulse event structure
b) adapt to boolean return value of add_pulse()
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This adds a DFS pattern detector to ath9k. It is fed with pulse events
by the radar pulse detector and reports in place whether a pattern
was detected. On detection, the result is reported as radar event to
the DFS management component in the upper layer.

Currently the ETSI DFS domain is supported with detector lines for
the patterns defined by EN-301-893 v1.5.1. Support for FCC and JP
will be added gradually.

To include the pattern detector, ath9k must be built with support
for DFS certified config flag set (CONFIG_ATH9K_DFS_CERTIFIED).
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>