Commit 6651ffc8
("ipv6: Fix tcp_v6_send_response transport header setting.")
fixed one half of why ipv6 tcp response checksums were
invalid, but it's not the whole story.

If we're going to use CHECKSUM_PARTIAL for these things (which we are
since commit 2e8e18ef "tcp: Set
CHECKSUM_UNNECESSARY in tcp_init_nondata_skb"), we can't be setting
buff->csum as we always have been here in tcp_v6_send_response.  We
need to leave it at zero.

Kill that line and checksums are good again.
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-6000.c
	net/core/dev.c

Fix the following RCU warning in dev_pick_tx():

===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
net/core/dev.c:1993 invoked rcu_dereference_check() without protection!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 0
2 locks held by swapper/0:
 #0:  (&idev->mc_ifc_timer){+.-...}, at: [<ffffffff81039e65>] run_timer_softirq+0x17b/0x278
 #1:  (rcu_read_lock_bh){.+....}, at: [<ffffffff812ea3eb>] dev_queue_xmit+0x14e/0x4dc

stack backtrace:
Pid: 0, comm: swapper Not tainted 2.6.34-rc5-cachefs #4
Call Trace:
 <IRQ>  [<ffffffff810516c4>] lockdep_rcu_dereference+0xaa/0xb2
 [<ffffffff812ea4f6>] dev_queue_xmit+0x259/0x4dc
 [<ffffffff812ea3eb>] ? dev_queue_xmit+0x14e/0x4dc
 [<ffffffff81052324>] ? trace_hardirqs_on+0xd/0xf
 [<ffffffff81035362>] ? local_bh_enable_ip+0xbc/0xc1
 [<ffffffff812f0954>] neigh_resolve_output+0x24b/0x27c
 [<ffffffff8134f673>] ip6_output_finish+0x7c/0xb4
 [<ffffffff81350c34>] ip6_output2+0x256/0x261
 [<ffffffff81052324>] ? trace_hardirqs_on+0xd/0xf
 [<ffffffff813517fb>] ip6_output+0xbbc/0xbcb
 [<ffffffff8135bc5d>] ? fib6_force_start_gc+0x2b/0x2d
 [<ffffffff81368acb>] mld_sendpack+0x273/0x39d
 [<ffffffff81368858>] ? mld_sendpack+0x0/0x39d
 [<ffffffff81052099>] ? mark_held_locks+0x52/0x70
 [<ffffffff813692fc>] mld_ifc_timer_expire+0x24f/0x288
 [<ffffffff81039ed6>] run_timer_softirq+0x1ec/0x278
 [<ffffffff81039e65>] ? run_timer_softirq+0x17b/0x278
 [<ffffffff813690ad>] ? mld_ifc_timer_expire+0x0/0x288
 [<ffffffff81035531>] ? __do_softirq+0x69/0x140
 [<ffffffff8103556a>] __do_softirq+0xa2/0x140
 [<ffffffff81002e0c>] call_softirq+0x1c/0x28
 [<ffffffff81004b54>] do_softirq+0x38/0x80
 [<ffffffff81034f06>] irq_exit+0x45/0x47
 [<ffffffff810177c3>] smp_apic_timer_interrupt+0x88/0x96
 [<ffffffff810028d3>] apic_timer_interrupt+0x13/0x20
 <EOI>  [<ffffffff810488dd>] ? __atomic_notifier_call_chain+0x0/0x86
 [<ffffffff810096bf>] ? mwait_idle+0x6e/0x78
 [<ffffffff810096b6>] ? mwait_idle+0x65/0x78
 [<ffffffff810011cb>] cpu_idle+0x4d/0x83
 [<ffffffff81380b05>] rest_init+0xb9/0xc0
 [<ffffffff81380a4c>] ? rest_init+0x0/0xc0
 [<ffffffff8168dcf0>] start_kernel+0x392/0x39d
 [<ffffffff8168d2a3>] x86_64_start_reservations+0xb3/0xb7
 [<ffffffff8168d38b>] x86_64_start_kernel+0xe4/0xeb

An rcu_dereference() should be an rcu_dereference_bh().
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

My recent patch to remove the open-coded checksum sequence in
tcp_v6_send_response broke it as we did not set the transport
header pointer on the new packet.

Actually, there is code there trying to set the transport
header properly, but it sets it for the wrong skb ('skb'
instead of 'buff').

This bug was introduced by commit
a8fdf2b3 ("ipv6: Fix
tcp_v6_send_response(): it didn't set skb transport header")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to export skb_under_panic() and skb_over_panic() in
skbuff.c, since these methods are used only in skbuff.c ; this patch
removes these two exports. It also marks these functions as 'static'
and removeS the extern declarations of them from
include/linux/skbuff.h
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse can help us find endianness bugs, but we need to make some
cleanups to be able to more easily spot real bugs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

grec_nsrcs is in network order, we should convert to host horder in
br_multicast_igmp3_report()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was merely an oversight when I added the *_gro_receive()
calls.
Signed-off-by: David S. Miller <davem@davemloft.net>

This was merely an oversight when I added the napi_gro_receive()
calls.
Signed-off-by: David S. Miller <davem@davemloft.net>

Define a new function to return the waitqueue of a "struct sock".

static inline wait_queue_head_t *sk_sleep(struct sock *sk)
{
	return sk->sk_sleep;
}

Change all read occurrences of sk_sleep by a call to this function.

Needed for a future RCU conversion. sk_sleep wont be a field directly
available.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  quota: Convert __DQUOT_PARANOIA symbol to standard config option

Make __DQUOT_PARANOIA define from the old days a standard config option
and turn it off by default.

This gets rid of a quota warning about writes before quota is turned on
for systems with ext4 root filesystem. Currently there's no way to legally
solve this because /etc/mtab has to be written before quota is turned on
on most systems.
Signed-off-by: Jan Kara <jack@suse.cz>

* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  pcmcia: fix error handling in cm4000_cs.c
  drivers/pcmcia: Add missing local_irq_restore
  serial_cs: MD55x support (PCMCIA GPRS/EDGE modem) (kernel 2.6.33)
  pcmcia: avoid late calls to pccard_validate_cis
  pcmcia: fix ioport size calculation in rsrc_nonstatic
  pcmcia: re-start on MFC override
  pcmcia: fix io_probe due to parent (PCI) resources
  pcmcia: use previously assigned IRQ for all card functions

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Fix hardirq tracing in trap return path.
  sparc64: Use correct pt_regs in decode_access_size() error paths.
  sparc64: Fix PREEMPT_ACTIVE value.
  sparc64: Run NMIs on the hardirq stack.
  sparc64: Allocate sufficient stack space in ftrace stubs.
  sparc: Fix forgotten kmemleak headers inclusion

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf: Fix unsafe frame rewinding with hot regs fetching

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: delay vblank cleanup until after driver unload

Before commit e28cbf22 ("improve
sys_newuname() for compat architectures") 64-bit x86 had a private
implementation of sys_uname which was just called sys_uname, which other
architectures used for the old uname.

Due to some merge issues with the uname refactoring patches we ended up
calling the old uname version for both the old and new system call
slots, which lead to the domainname filed never be set which caused
failures with libnss_nis.
Reported-and-tested-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since netdev_chain is guarded by rtnl_lock, ASSERT_RTNL should be
present here to make sure that all callers of call_netdevice_notifiers
does the locking properly.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case we compute a software skb->rxhash, we can generate a consistent
hash : Its value will be the same in both flow directions.

This helps some workloads, like conntracking, since the same state needs
to be accessed in both directions.

tbench + RFS + this patch gives better results than tbench with default
kernel configuration (no RPS, no RFS)

Also fixed some sparse warnings.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct softnet_data holds many queues, so consistent use "sd" name
instead of "queue" is better.

Adds a rps_ipi_queued() helper to cleanup enqueue_to_backlog()

Adds a _and_irq_disable suffix to net_rps_action() name, as David
suggested.

incr_input_queue_head() becomes input_queue_head_incr()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can overflow the hardirq stack if we set the %pil here
so early, just let the normal control flow do it.

This is fine as we are allowed to do the actual IRQ enable
at any point after we call trace_hardirqs_on.
Signed-off-by: David S. Miller <davem@davemloft.net>

Drivers may use vblank calls now (e.g. drm_vblank_off) in their unload
paths, so don't clean up the vblank related structures until after
driver unload.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The recent anon_vma fixes cause many anonymous pages to end up
in the parent process anon_vma, even when the page is exclusively
owned by the current process.

Adding exclusively owned anonymous pages to the top anon_vma
reduces rmap scanning overhead, especially in workloads with
forking servers.

This patch adds a parameter to __page_set_anon_rmap that can
be used to indicate whether or not the added page is exclusively
owned by the current process.

Pages added through page_add_new_anon_rmap are exclusively
owned by the current process, and can be added to the top
anon_vma.

Pages added through page_add_anon_rmap can be either shared
or exclusively owned, so we do the conservative thing and
add it to the oldest anon_vma.

A next step would be to add the exclusive parameter to
page_add_anon_rmap, to be used from functions where we do
know for sure whether a page is exclusively owned.
Signed-off-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Lightly-tested-by: Borislav Petkov <bp@alien8.de>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
[ Edited to look nicer  - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

store_rps_map() & store_rps_dev_flow_table_cnt() are static.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
  eCryptfs: Turn lower lookup error messages into debug messages
  eCryptfs: Copy lower directory inode times and size on link
  ecryptfs: fix use with tmpfs by removing d_drop from ecryptfs_destroy_inode
  ecryptfs: fix error code for missing xattrs in lower fs
  eCryptfs: Decrypt symlink target for stat size
  eCryptfs: Strip metadata in xattr flag in encrypted view
  eCryptfs: Clear buffer before reading in metadata xattr
  eCryptfs: Rename ecryptfs_crypt_stat.num_header_bytes_at_front
  eCryptfs: Fix metadata in xattr feature regression

Signed-off-by: Alexander Kuznetsov <alr.kuznetsov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Since "mac80211: make off-channel work generic" drivers have not been
notified of configuration changes after association or authentication. This
caused more dependence on current state to ensure driver will be notified
when configuration changes occur. One such problem arises if off-channel is
in progress when HT information changes. Since HT is only enabled on the
"oper_channel" the driver will never be notified of this change. Usually
the driver is notified soon after of a BSS information change
(BSS_CHANGED_HT) ... but since the driver did not get a notification that
this is a HT channel the new BSS information does not make sense.

Fix this by also changing the off-channel information when HT is enabled
and thus cause driver to be notified correctly.

This fixes a problem in 4965 when associated with 5GHz 40MHz channel.
Without this patch the system can associate but is unable to transfer any
data, not even ping.

See http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2158Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the addba timer expires but has no work to do,
it should not affect the state machine. If it does,
TX will not see the successfully established and we
can also crash trying to re-establish the session.

Cc: stable@kernel.org [2.6.32, 2.6.33]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

net_rps_action() is a bit expensive on NR_CPUS=64..4096 kernels, even if
RPS is not active.

Tom Herbert used two bitmasks to hold information needed to send IPI,
but a single LIFO list seems more appropriate.

Move all RPS logic into net_rps_action() to cleanup net_rx_action() code
(remove two ifdefs)

Move rps_remote_softirq_cpus into softnet_data to share its first cache
line, filling an existing hole.

In a future patch, we could call net_rps_action() from process_backlog()
to make sure we send IPI before handling this cpu backlog.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set version to 1.52.53-1.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Author: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move "don't shut down the power" logic into bnx2x_set_power_state() to make the code cleaner.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Properly mask the value to be written to the register (according to the register size) during the self-test.
Otherwise immediate parity error would be generated.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Try to enable less MSI-X vectors if initial request has failed.

Author: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added total_mcast/bcast_pkts_transmitted statistics.

Author: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

White spaces, code readability and prints.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>