This patch add support for tdls channel switch event process.
We block TX queues for particular RA list depending upon channel
switch state. If channel switch state is moving to base channel,
we unblock RA lists for AP. If channel switch state is moving to off
channel, we unblock TDLS peer RA lists.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch add new tdls status used for tdls channel switch.
Driver in turn would block cmd path and data path if tdls
channel switching. Data path to non tdls peer should be blocked
if tdls channel switch to off-channel.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If tx_pkts_queued is increased for tx paused receive address, tx process
will be triggered for this packet. But since RA list was tx paused,
there will be an infinite loop in mwifiex_wmm_process_tx waiting for the
event(tx pause, tdls cs) to cancel tx pause. This will be an dead loop,
since main_process was locked at this time, there will be no opportunity
to process event.

So do not increase tx_pkts_queued if receive address tx paused,
this will be restored RA list is unpaused.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Data traffic to tx paused receive address should be blocked.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds support to enable TX data pause feature for mwifiex.
Whenever FW TX buffers reach threshold, FW would send TX pause event
to driver. Driver in turn would block data traffic to that particular
receiver address.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In the rtlwifi/rtl8192cu, rtl8723 code is dead code.
So I remove it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Major changes in ath10k:

* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch

FCC long pulse radar (type 5) requires pulses to be
checked for chirping. This patch implements chirp
detection based on the FFT data provided for long
pulses.

A chirp is detected when a set of criteria defined
by FCC pulse characteristics is met, including
* have at least 4 FFT samples
* max_bin index moves equidistantly between samples
* the gradient is within defined range

The chirp detection has been tested with reference
radar generating devices and proved to work reliably.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The chip reports radar pulses on extension channel
even if operating in HT20 mode. This patch adds a
sanity check for HT40 mode before it feeds pulses
on extension channel to the pattern detector.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

commit 2c86c275 ("Add ipw2100 wireless driver.") introduced
HW_PHY_OFF_LOOP_DELAY (HZ / 5000) which always evaluated to 0. Clarified
by Stanislav Yakovlev <stas.yakovlev@gmail.com> that it should be 50
milliseconds thus fixed up to msecs_to_jiffies(50).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Concurrent AP/GO operation on different channels
isn't really supported well by the firmware so
it's better to remove it from being advertised.

Also tune the way station and p2p client interface
limits are expressed to allow station + 2x p2p
client or station + p2p client + p2p go.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Whenever any vdev was supposed to be paused all Tx
queues were stopped (except offchannel) instead of
only these associated with the given vdev.

This caused subtle issues with
multi-channel/multi-vif scenarios, e.g.
authentication of station vif could sometimes fail
depending on fw tx pause request timing.

Fixes: b4aa539d ("ath10k: implement tx pause wmi event")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Psmode can be forcefully enabled when vdev isn't
started. It isn't guaranteed that mac80211 will
re-issue psmode setting after vdev is started
unless actual bss_conf.ps value has changed.

Even if this doesn't fix any problems now it may
prevent future breakage.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The expiration function must not be called when
roc is explicitly cancelled by mac80211. However
since fcf98446 ("ath10k: fix hw roc
expiration") the notification was never sent when
roc actually expired.

This fixes some P2P connection setup issues.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Further testing proved that multi-channel AP+STA
on QCA6174 with RM.2.0-00088 should have powersave
force-disabled to avoid beacon misses/skipping on
either side which in turn could disrupt
communication.

Since AP never has arvif->ps don't even bother
checking it. Other combinations may be broken as
well so disallow powersave with multivif outright
unless firmware advertises otherwise.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

mac80211 already does provide complete IEs for
Probe Requests for hw scan and ath10k firmware was
appending duplicate Supported Rates IEs
unnecessarily.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In commit 418ca599 ("ath10k: Make target cpu address to
CE address conversion chip specific") mask 0x7fff is added
by mistake instead of 0x7ff. Fix this regression.

Fixes: 418ca599 ("ath10k: Make target cpu address to CE address conversion chip specific")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

commit a521ee98 ("ath10k: Add new reg_address/mask to hw register
table") broke QCA61x4 support by providing wrong
fw_indicator_address, which should have been 0x0003a028 instead of 0x00009028.

User experience was a failing boot up sequence (crashing device during
initialization):

[  181.663874] ath10k_pci 0000:02:00.0: enabling device (0000 -> 0002)
[  181.664787] ath10k_pci 0000:02:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0
[  181.688886] ath10k_pci 0000:02:00.0: device has crashed during init
[  181.688897] ath10k_pci 0000:02:00.0: failed to wait for target after cold reset: -70
[  181.688902] ath10k_pci 0000:02:00.0: failed to reset chip: -70
[  181.689774] ath10k_pci: probe of 0000:02:00.0 failed with error -70

Fix it by updating the address with correct value.

Fixes: a521ee98 ("ath10k: Add new reg_address/mask to hw register table")
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Sathya Perla says:

====================
be2net: patch set

Hi David, the following patch set has code cleanup patches, minor enhancements
and non-critical fixes. Pls consider applying to the net-next tree. Thanks!

Patch 1 removes duplicate code in be_setup_wol() routine making it simpler
and more readable.

Patch 2 fixes the the bridge mode return value for the ndo_bridge_getlink()
call. Instead of just relying on the SRIOV enabled state, the driver now
queries the FW, for the actual mode of bridge.

Patch 3 removes code for setting D0 power state as it's already done
in pci_enable_device()

Patch 4 fixes a bad return value in be_check_ufi_compatibility() routine
introduced by an earlier commit.

Patch 5 fixes a field in udp header being accessed while in network endian
format.

Patch 6 fixes the be_mcc_notify() routine to return an error status when
the FW/HW is in an error state.

Patch 7 fixes the be_cmd_rx_filter() routine to issue the RX_FILTER cmd
and not wait for a completion from the FW. If the FW/adapter
is in an error state, this change helps in not holding up the rtnl_lock
and keeping bottom halves disabled while the driver timesout waiting for
a response from the FW.

Patch 8 fixes the be_cmd_set_loopback() routine to issue the LOOPBACK cmd
and not wait for the FW completion while spin_lock_bh() is held on the
mcc_lock. As the cmd is always issued from ethtool in a process context,
it can sleep till the FW completion is received.

Patch 9 bumps up the driver version to 10.6.0.3
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SET_LOOPBACK_MODE command is always issued from ethtool only in a
process context. So, while waiting for the cmd to complete, the driver
can sleep instead of holding spin_lock_bh() on the mcc_lock. This is done
by calling be_mcc_notify() instead of be_mcc_notify_wait() (that returns
only after the cmd completes while the MCCQ is locked).
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fix makes the RX_FILTER cmd asynchronous, i.e., the caller issues
this cmd and doesn't wait for a completion from the FW. If the FW/adapter
is in an error state, this change helps in not holding up the rtnl_lock
and keeping bottom halves disabled while the driver timesout waiting for
a response from the FW.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the adapter is in error state, return error from be_mcc_notify()
so that the caller routines need not sleep waiting for a response.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "dest" field in the UDP-hdr of a TX skb is in network endian format.
Convert it to host endian before accessing it. The os2bmc patch,
mentioned below introduced this code.

Fixes: 760c295e ("be2net: Support for OS2BMC")
Signed-off-by: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the commit a6e6ff6e
("be2net: simplify UFI compatibility checking"), a return value of "-1"
was incorrectly used in place of "false". This patch fixes it.

Fixes: a6e6ff6e ("be2net: simplify UFI compatibility checking")
Signed-off-by: Vasundhara Volam <vasundhara.volam@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pci_enable_device() call sets device power state to D0; there is no need
doing it again.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current code assumes that bridge functionality (EVB) in the adapter
is enabled only when SR-IOV is enabled. This is not always true.
This patch uses the GET_HSW_CONFIG FW cmd to query this from the FW.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change will make be_setup_wol() routine more compact and readable
by removing some duplicate code.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If outgoing interface is specified and the candidate address is
restricted to the outgoing interface, it is enough to iterate
over that given interface only.
Signed-off-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Support manually setting the polarity to mdi or mdix
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass the mdix setting from ethtool down to the phy driver, to allow
driver specific implementations of manually setting the polarity.
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 900f65d3 ("tcp: move duplicate code from
tcp_v4_init_sock()/tcp_v6_init_sock()"), we no longer
need to export tcp_init_xmit_timers()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fill also the port group state when sending notifications.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

flags local variable in __mkroute_input is not used as a variable.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support to allow non-local binds similar to how this was done for IPv4.
Non-local binds are very useful in emulating the Internet in a box, etc.

This add the ip_nonlocal_bind sysctl under ipv6.

Testing:

Set up nonlocal binding and receive routing on a host, e.g.:

ip -6 rule add from ::/0 iif eth0 lookup 200
ip -6 route add local 2001:0:0:1::/64 dev lo proto kernel scope host table 200
sysctl -w net.ipv6.ip_nonlocal_bind=1

Set up routing to 2001:0:0:1::/64 on peer to go to first host

ping6 -I 2001:0:0:1::1 peer-address -- to verify
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
inet: timewait cleanups

Another round of patches to make tw handling simpler.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

inet_twsk_deschedule() calls are followed by inet_twsk_put().

Only particular case is in inet_twsk_purge() but there is no point
to defer the inet_twsk_put() after re-enabling BH.

Lets rename inet_twsk_deschedule() to inet_twsk_deschedule_put()
and move the inet_twsk_put() inside.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

timewait sockets have a complex refcounting logic.
Once we realize it should be similar to established and
syn_recv sockets, we can use sk_nulls_del_node_init_rcu()
and remove inet_twsk_unhash()

In particular, deferred inet_twsk_put() added in commit
13475a30 ("tcp: connect() race with timewait reuse")
looks unecessary : When removing a timewait socket from
ehash or bhash, caller must own a reference on the socket
anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kernel will crash the same if one of the pointer is NULL anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>