In commit 9c204b46
(ath9k_hw: do not limit initial tx power to 20 dbm),
setting of txpower was broken.

This patch fixes it by initializing reg_pwr from the new
power limit, not the previous value.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It was not possible to guess the conditions from MMIO dumps. Take them
from brcmsmac code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We've compared b43 with brcmsmac and took functions names from the
later.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is not implemented in brcmsmac, but was noticed in (newer) wl. Can
be workaround for some hardware bug.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The biggest change is reversing order of reading 32-bit table value.
MMIO dumps has shown it's done that way for LCN-PHY.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: zero.lin <zero.lin@ralinktech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Introduce filtering for scheduled scans to reduce the number of
unnecessary results (which cause useless wake-ups).

Add a new nested attribute where sets of parameters to be matched can
be passed when starting a scheduled scan.  Only scan results that
match any of the sets will be returned.

At this point, the set consists of a single parameter, an SSID.  This
can be easily extended in the future to support more complex matches.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

add WIPHY_FLAG_AP_UAPSD flag to indicate uapsd support on
AP mode.

Advertise it to userspace by including a new
NL80211_ATTR_SUPPORT_AP_UAPSD attribute.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

unsigned shorts and unsigned chars are never == -1.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

"vif" is assigned twice.  We can remove the first one.

This silences a Smatch warning that "ctx" could be one step past the
end of the priv->contexts[] array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Rx latecy to start signal(usec) of 11a is 41 not 37 and
also corrected the rx delay in quarter rate.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The calls to kzalloc() weren't checked here and it upsets the static
checkers.  Obviously they're not super likely to fail, but we might
as well add some error handling.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When this flag is set, Tx A-MPDU sessions will not be started by
mac80211. This flag is required for devices that support Tx A-MPDU setup
in hardware.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Removing unnecessary messages saves code and text.

Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Removing unnecessary messages saves code and text.

Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Removing unnecessary messages saves code and text.

Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

No need to take the mpath state lock when an mpath is removed.
Also, no need checking the lock when reading mpath flags.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When an interface is removed, the mesh paths associated with it should
also be removed.

This fixes a bug we observed when reloading a device driver module
without reloading mac80211s.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reported by Pedro Larbig (ASPj)
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Sequence of kmalloc/kzalloc and memcpy is replaced with
kmemdup.

Cc: Walter Harms <wharms@bfs.de>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit "ath9k_hw: Fix exceed transmission burst-time of 5GHz" added
a padding of 60 delimiters on the first subframe to work around an issue
on AR9380, but it lacked the checks to prevent it from being applied to
pre-AR9380, enterprise AR9380 or AR9580+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This will avoid mac80211 to trigger PS mode for connected station
based on the PM bit of incoming frames. AP firmware is capable of
handling such frames and buffering TX frames destined to the
stations that are in PS mode.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The previous register used in these initvals was probably accidentally
copied over from the AR9100 values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It was used for the defunct 'turbo' mode which was never implemented in the
driver. Saves ~7.5k uncompressed
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the rssi of the current AP drops, both wpa_supplicant and the
firmware may do a background scan to find a better AP and try to
associate. Since firmware based roaming is faster, inform
wpa_supplicant to avoid roaming and let the firmware decide to
roam if necessary.

For fullmac drivers like ath6kl, it is just enough to provide the
ESSID and the firmware will decide on the BSSID. Since it is not
possible to do pre-auth during roaming for fullmac drivers, the
wpa_supplicant needs to completely disconnect with the old AP and
reconnect with the new AP. This consumes lot of time and it is
better to leave the roaming decision to the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Unfortunately failed BAR tx attempts happen more frequently than I
expected, and the resulting aggregation teardowns cause performance
issues, as the aggregation session does not always get re-established
properly.
Instead of tearing down the entire aggr session, we can simply store the
SSN of the last failed BAR tx attempt, wait for the first successful
tx status event, and then send another BAR with the same SSN.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Specs say about size 2 (u16) and my 14e4:4727 has board rev 0x1211.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Switching is not fully implemented yet, prepare place for the code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

It is only used to workaround interoperability issues related to longer
delays in receiving the block ack, so it is not necessary to apply it
to the CTS exchange.
Should improve throughput slightly, especially when there are lots
of retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Under failure conditions, the mesh stack sends PERR messages to the
previous sender of the failed frame.  This happens in the tx feedback
path, in which the transmission queue lock may be taken.  Avoid a
deadlock by sending the path error via the pending queue.
Signed-off-by: John W. Linville <linville@tuxdriver.com>