- 06 Jun, 2017 40 commits
-
-
Niklas Söderlund authored
There is only one subdevice registered with the async framework so there is no need for the driver to check which subdevice is bound or unbound. Remove these checks since the async framework preforms this. Signed-off-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> [hans.verkuil@cisco.com: fix typo: surce -> source] Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com>
-
Niklas Söderlund authored
With the driver stopping and starting the stream each time the driver is stalled rvin_capture_off() can be folded in to the only caller. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Niklas Söderlund authored
If userspace can't feed the driver with buffers as fast as the driver consumes them the driver will stop video capturing and wait for more buffers from userspace, the driver is stalled. Once it have been feed one or more free buffers it will recover from the stall and resume capturing. Instead of continue to capture using the same capture mode as before the stall allow the driver to choose between single and continuous mode based on free buffer availability. Do this by stopping capturing when the driver becomes stalled and restart capturing once it continues. By doing this the capture mode will be evaluated each time the driver is recovering from a stall. This behavior is needed to fix a bug where continuous capturing mode is used, userspace is about to stop the stream and is waiting for the last buffers to be returned from the driver and is not queuing any new buffers. In this case the driver becomes stalled when there are only 3 buffers remaining streaming will never resume since the driver is waiting for userspace to feed it more buffers before it can continue streaming. With this fix the driver will then switch to single capture mode for the last 3 buffers and a deadlock is avoided. The issue can be demonstrated using yavta. $ yavta -f RGB565 -s 640x480 -n 4 --capture=10 /dev/video22 Device /dev/video22 opened. Device `R_Car_VIN' on `platform:e6ef1000.video' (driver 'rcar_vin') supports video, capture, without mplanes. Video format set: RGB565 (50424752) 640x480 (stride 1280) field interlaced buffer size 614400 Video format: RGB565 (50424752) 640x480 (stride 1280) field interlaced buffer size 614400 4 buffers requested. length: 614400 offset: 0 timestamp type/source: mono/EoF Buffer 0/0 mapped at address 0xb6cc7000. length: 614400 offset: 614400 timestamp type/source: mono/EoF Buffer 1/0 mapped at address 0xb6c31000. length: 614400 offset: 1228800 timestamp type/source: mono/EoF Buffer 2/0 mapped at address 0xb6b9b000. length: 614400 offset: 1843200 timestamp type/source: mono/EoF Buffer 3/0 mapped at address 0xb6b05000. 0 (0) [-] interlaced 0 614400 B 38.240285 38.240303 12.421 fps ts mono/EoF 1 (1) [-] interlaced 1 614400 B 38.282329 38.282346 23.785 fps ts mono/EoF 2 (2) [-] interlaced 2 614400 B 38.322324 38.322338 25.003 fps ts mono/EoF 3 (3) [-] interlaced 3 614400 B 38.362318 38.362333 25.004 fps ts mono/EoF 4 (0) [-] interlaced 4 614400 B 38.402313 38.402328 25.003 fps ts mono/EoF 5 (1) [-] interlaced 5 614400 B 38.442307 38.442321 25.004 fps ts mono/EoF 6 (2) [-] interlaced 6 614400 B 38.482301 38.482316 25.004 fps ts mono/EoF 7 (3) [-] interlaced 7 614400 B 38.522295 38.522312 25.004 fps ts mono/EoF 8 (0) [-] interlaced 8 614400 B 38.562290 38.562306 25.003 fps ts mono/EoF <blocks forever, waiting for the last buffer> This fix also allow the driver to switch to single capture mode if userspace doesn't feed it buffers fast enough. Or the other way around, if userspace suddenly feeds the driver buffers faster it can switch to continues capturing mode. Signed-off-by:
-
Niklas Söderlund authored
Instead of selecting single or continuous capture mode based on how many buffers userspace intends to give us select capture mode based on number of free buffers we can allocate to hardware when the stream is started. This change is a prerequisite to enable the driver to switch from continuous to single capture mode (or the other way around) when the driver is stalled by userspace not feeding it buffers as fast as it consumes it. Signed-off-by:
-
Niklas Söderlund authored
This only moves whole structs, defines and functions around, no code is changed inside any function. The reason for moving this code around is to prepare for refactoring and fixing of a start/stop stream bug without having to use forward declarations. Signed-off-by:
-
Niklas Söderlund authored
It's possible to grab frames using only one buffer, this should never have been set to anything else then 1. Signed-off-by:
-
Niklas Söderlund authored
Use information about pad index when enumerating mbus codes. Signed-off-by:
-
Niklas Söderlund authored
Information about pads will be needed when enumerating the media bus codes in the async complete handler which is run before rvin_v4l2_probe(). Move the pad lookup to the async bound handler so they are available when needed. Signed-off-by:
-
Niklas Söderlund authored
The pad lookup code can be broken out to increase readability and to reduce code duplication. Signed-off-by:
-
Niklas Söderlund authored
It makes more sense to store the sink and source pads in struct rvin_graph_entity since that contains other subdevice related information. The data type to store pad information in is unsigned int and not int, change this. While we are at it drop the _idx suffix from the names, this never made sense. Signed-off-by:
-
Niklas Söderlund authored
The driver supports a single input only, which can be either analog or digital. If the subdevice supports dv_timings_cap the input is digital and the driver should not fill in the standard. Signed-off-by:
-
Niklas Söderlund authored
The rcar-vin driver only uses one pad, pad number 0. - All v4l2 operations that did not check that the requested operation was for pad 0 have been updated with a check to enforce this. - All v4l2 operations that stored (and later restored) the requested pad before substituting it for the subdevice pad number have been updated to not store the incoming pad and simply restore it to 0 after the subdevice operation is complete. Signed-off-by:
-
Niklas Söderlund authored
Use rvin_reset_format() in rvin_s_dv_timings() instead of just resetting a few fields. This fixes an issue where the field format was not properly set after S_DV_TIMINGS. Signed-off-by:
-
Niklas Söderlund authored
These two were forgotten when refactoring the format reset code. If they are not also reset at the same time as width and height the format returned from G_FMT will not match reality. Signed-off-by:
-
Sakari Ailus authored
All drivers have been converted from V4L2 OF to V4L2 fwnode. The V4L2 OF framework is now unused. Remove it. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Sakari Ailus authored
Instead of including the V4L2 OF header in ReST documentation, use the V4L2 fwnode header instead. Signed-off-by:
-
Sakari Ailus authored
Switch users of the v4l2_of_ APIs to the more generic v4l2_fwnode_ APIs. Async OF matching is replaced by fwnode matching and OF matching support is removed. Signed-off-by:
-
Sakari Ailus authored
Pass the more generic fwnode_handle to the init function than the device_node. Signed-off-by:
-
Sakari Ailus authored
Add fwnode matching to complement OF node matching. And fwnode may also be an OF node. Do not enable fwnode matching yet. It will replace OF matching soon. Signed-off-by:
-
Sakari Ailus authored
The fwnode_handle is a more generic way than OF device_node to describe firmware nodes. Instead of the OF API, use more generic fwnode API to obtain the same information. As the V4L2 fwnode support will be required by a small minority of e.g. ACPI based systems (the same might actually go for OF), make this a module instead of embedding it in the videodev module. The origins of the V4L2 fwnode framework is in the V4L2 OF framework. Signed-off-by:
-
Sean Young authored
The lirc_zilog driver is the last remaining lirc driver, so the existing todo is no longer relevant. Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Sean Young authored
Inlining these functions into the probe function makes it much more readable. Signed-off-by:
-
Sean Young authored
These functions are too short and removing them makes the code more readable. Signed-off-by:
-
Sean Young authored
Several error paths do not free up resources. This simplifies the code and fixes this. Signed-off-by:
-
Sean Young authored
If the probe fails (e.g. port already in use), rmmod causes null deref. Signed-off-by:
-
Ricardo Silva authored
Fix all checkpatch reported issues for: * CHECK: "braces {} should be used on all arms of this statement". * CHECK: "Unbalanced braces around else statement". Make sure all if/else statements are balanced in terms of braces. Most cases in code are, but a few were left unbalanced, so put them all consistent with the recommended style. Signed-off-by:Ricardo Silva <rjpdasilva@gmail.com> Signed-off-by:
-
Ricardo Silva authored
Fix all checkpatch reported issues for "CHECK: Prefer kzalloc(sizeof(*<p>)...) over kzalloc(sizeof(struct <P>)...)". Other similar case in the code already using recommended style, so make it all consistent with the recommended practice. Signed-off-by:
-
Ricardo Silva authored
Fix all checkpatch reported issues for "CHECK: Prefer using '"%s...", __func__' to using '<func_name>', ..." Use recommended style. Additionally, __func__ was already used in similar cases throughout the code, so make it all consistent. Signed-off-by:
-
Ricardo Silva authored
Fix all checkpatch reported issues for "CHECK: Comparison to NULL could be written...". Do these comparisons using the recommended coding style and consistent with other similar cases in the file, which already used the recommended way. Signed-off-by:
-
Ricardo Silva authored
Fix style issues reported by checkpatch, affecting whitespace only: * CHECK: "Please don't use multiple blank lines". Two of these still triggering and left untouched because used for separating logical blocks (vars from functions, etc.). * CHECK: "spaces preferred around that '<operator>'". All fixed. * CHECK: "Alignment should match open parenthesis". All fixed except one on line 1161, left untouched for readability. Move towards recommended coding style without compromising readability. Signed-off-by:
-
David Härdeman authored
The key_addr member is only assigned, never used. So, remove it. Signed-off-by:
David Härdeman <david@hardeman.nu> Signed-off-by:
-
David Härdeman authored
Just some debug statements to change. Signed-off-by:
-
David Härdeman authored
Changing the protocol does not imply that the keymap changes. Signed-off-by:
-
David Härdeman authored
The REP_DELAY setting on the input device is independent of hardware. This change should not change how to driver works (as it does a keydown/keyup and has no real repeat handling). Signed-off-by:
-
David Härdeman authored
Remove some stuff from lirc_dev.h which is not used anywhere. Signed-off-by:
-
David Härdeman authored
Remove superfluous includes and defines. Signed-off-by:
-
David Härdeman authored
Most drivers return both values when the device is gone. Signed-off-by:
-
David Härdeman authored
The "debug" parameter isn't actually used anywhere. Signed-off-by:
-
David Härdeman authored
device_add() and friends already manage the references to the parent device so these calls aren't necessary. Signed-off-by:
-
David Härdeman authored
These two functions only make the logic in lirc_register_driver() harder to follow. (Note that almost no other driver calls kobject_set_name() on their cdev so I simply removed that part). Signed-off-by:
-
