The Ethernet switch has an embedded interrupt controller. Interrupts
from the embedded PHYs are part of this interrupt controller.
Explicitly list the MDIO bus the embedded PHYs are on, and wire up the
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not all boards have the interrupt output from the switch connected to
a GPIO line. In such cases, phylib has to poll the internal PHYs,
rather than receive an interrupt when there is a change in the link
state. phylib polls once per second, and per PHY reads around 4
words. With a switch typically having 4 internal PHYs, this means 16
MDIO transactions per second.

Rather than performing this phylib level polling, have the driver poll
the interrupt status register. If the status register indicates an
interrupt condition processing of interrupts in the same way as if a
GPIO was used.

Polling 10 times a second places less load on the MDIO bus. But rather
than taking on average 0.5s to detect a link change, it takes less
than 0.05s. Additionally, other interrupts, such as the watchdog, ATU
and VTU violations will be reported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Up until now we only allowed VLAN devices to be put in a VLAN-unaware
bridge, but some users need the ability to enslave physical ports as
well.

This is achieved by mapping the port and VID 1 to the bridge's vFID,
instead of the port and the VID used by the VLAN device.

The above is valid because as long as the port is not enslaved to a
bridge, VID 1 is guaranteed to be configured as PVID and egress
untagged.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2018-02-26

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) Various improvements for BPF kselftests: i) skip unprivileged tests
   when kernel.unprivileged_bpf_disabled sysctl knob is set, ii) count
   the number of skipped tests from unprivileged, iii) when a test case
   had an unexpected error then print the actual but also the unexpected
   one for better comparison, from Joe.

2) Add a sample program for collecting CPU state statistics with regards
   to how long the CPU resides in cstate and pstate levels. Based on
   cpu_idle and cpu_frequency trace points, from Leo.

3) Various x64 BPF JIT optimizations to further shrink the generated
   image size in order to make it more icache friendly. When tested on
   the Cilium generated programs, image size reduced by approx 4-5% in
   best case mainly due to how LLVM emits unsigned 32 bit constants,
   from Daniel.

4) Improvements and fixes on the BPF sockmap sample programs: i) fix
   the sockmap's Makefile to include nlattr.o for libbpf, ii) detach
   the sock ops programs from the cgroup before exit, from Prashant.

5) Avoid including xdp.h in filter.h by just forward declaring the
   struct xdp_rxq_info in filter.h, from Jesper.

6) Fix the BPF kselftests Makefile for cgroup_helpers.c by only declaring
   it a dependency for test_dev_cgroup.c but not every other test case
   where it is not needed, from Jesper.

7) Adjust rlimit RLIMIT_MEMLOCK for test_tcpbpf_user selftest since the
   default is insufficient for creating the 'global_map' used in the
   corresponding BPF program, from Yonghong.

8) Likewise, for the xdp_redirect sample, Tushar ran into the same when
   invoking xdp_redirect and xdp_monitor at the same time, therefore
   in order to have the sample generically work bump the limit here,
   too. Fix from Tushar.

9) Avoid an unnecessary NULL check in BPF_CGROUP_RUN_PROG_INET_SOCK()
   since sk is always guaranteed to be non-NULL, from Yafang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

CPU is active when have running tasks on it and CPUFreq governor can
select different operating points (OPP) according to different workload;
we use 'pstate' to present CPU state which have running tasks with one
specific OPP.  On the other hand, CPU is idle which only idle task on
it, CPUIdle governor can select one specific idle state to power off
hardware logics; we use 'cstate' to present CPU idle state.

Based on trace events 'cpu_idle' and 'cpu_frequency' we can accomplish
the duration statistics for every state.  Every time when CPU enters
into or exits from idle states, the trace event 'cpu_idle' is recorded;
trace event 'cpu_frequency' records the event for CPU OPP changing, so
it's easily to know how long time the CPU stays in the specified OPP,
and the CPU must be not in any idle state.

This patch is to utilize the mentioned trace events for pstate and
cstate statistics.  To achieve more accurate profiling data, the program
uses below sequence to insure CPU running/idle time aren't missed:

- Before profiling the user space program wakes up all CPUs for once, so
  can avoid to missing account time for CPU staying in idle state for
  long time; the program forces to set 'scaling_max_freq' to lowest
  frequency and then restore 'scaling_max_freq' to highest frequency,
  this can ensure the frequency to be set to lowest frequency and later
  after start to run workload the frequency can be easily to be changed
  to higher frequency;

- User space program reads map data and update statistics for every 5s,
  so this is same with other sample bpf programs for avoiding big
  overload introduced by bpf program self;

- When send signal to terminate program, the signal handler wakes up
  all CPUs, set lowest frequency and restore highest frequency to
  'scaling_max_freq'; this is exactly same with the first step so
  avoid to missing account CPU pstate and cstate time during last
  stage.  Finally it reports the latest statistics.

The program has been tested on Hikey board with octa CA53 CPUs, below
is one example for statistics result, the format mainly follows up
Jesper Dangaard Brouer suggestion.

Jesper reminds to 'get printf to pretty print with thousands separators
use %' and setlocale(LC_NUMERIC, "en_US")', tried three different arm64
GCC toolchains (5.4.0 20160609, 6.2.1 20161016, 6.3.0 20170516) but all
of them cannot support printf flag character %' on arm64 platform, so go
back print number without grouping mode.

CPU states statistics:
state(ms)  cstate-0    cstate-1    cstate-2    pstate-0    pstate-1    pstate-2    pstate-3    pstate-4
CPU-0      767         6111        111863      561         31          756         853         190
CPU-1      241         10606       107956      484         125         646         990         85
CPU-2      413         19721       98735       636         84          696         757         89
CPU-3      84          11711       79989       17516       909         4811        5773        341
CPU-4      152         19610       98229       444         53          649         708         1283
CPU-5      185         8781        108697      666         91          671         677         1365
CPU-6      157         21964       95825       581         67          566         684         1284
CPU-7      125         15238       102704      398         20          665         786         1197

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Daniel Borkmann says:

====================
Couple of minor improvements to the x64 JIT I had still around from
pre merge window in order to shrink the image size further. Added
test cases for kselftests too as well as running Cilium workloads on
them w/o issues.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Add few test cases that check the rnu-time results under JIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

While it's rather cumbersome to reduce prologue for cBPF->eBPF
migrations wrt spill/fill for r15 which is callee saved register
due to bpf_error path in bpf_jit.S that is both used by migrations
as well as native eBPF, we can still trivially save 5 bytes in
prologue for the former since tail calls can never be used there.
cBPF->eBPF migrations also have their own custom prologue in BPF
asm that xors A and X reg anyway, so it's fine we skip this here.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Add a generic emit_mov_reg() helper in order to reuse it in BPF
multiplication to load the src into rax, we can save a few bytes
in alu32 while doing so.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Instead of unconditionally performing push/pop on rax/rdx
in case of multiplication, we can save a few bytes in case
of dest register being either BPF r0 (rax) or r3 (rdx)
since the result is written in there anyway.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

While analyzing some of the more complex BPF programs from Cilium,
I found that LLVM generally prefers to emit LD_IMM64 instead of MOV32
BPF instructions for loading unsigned 32-bit immediates into a
register. Given we cannot change the current/stable LLVM versions
that are already out there, lets optimize this case such that the
JIT prefers to emit 'mov %eax, imm32' over 'movabsq %rax, imm64'
whenever suitable in order to reduce the image size by 4-5 bytes per
such load in the typical case, reducing image size on some of the
bigger programs by up to 4%. emit_mov_imm32() and emit_mov_imm64()
have been added as helpers.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

When we shift by one, we can use a different encoding where imm
is not explicitly needed, which saves 1 byte per such op.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

Pull networking fixes from David Miller:

 1) Fix TTL offset calculation in mac80211 mesh code, from Peter Oh.

 2) Fix races with procfs in ipt_CLUSTERIP, from Cong Wang.

 3) Memory leak fix in lpm_trie BPF map code, from Yonghong Song.

 4) Need to use GFP_ATOMIC in BPF cpumap allocations, from Jason Wang.

 5) Fix potential deadlocks in netfilter getsockopt() code paths, from
    Paolo Abeni.

 6) Netfilter stackpointer size checks really are needed to validate
    user input, from Florian Westphal.

 7) Missing timer init in x_tables, from Paolo Abeni.

 8) Don't use WQ_MEM_RECLAIM in mac80211 hwsim, from Johannes Berg.

 9) When an ibmvnic device is brought down then back up again, it can be
    sent queue entries from a previous session, handle this properly
    instead of crashing. From Thomas Falcon.

10) Fix TCP checksum on LRO buffers in mlx5e, from Gal Pressman.

11) When we are dumping filters in cls_api, the output SKB is empty, and
    the filter we are dumping is too large for the space in the SKB, we
    should return -EMSGSIZE like other netlink dump operations do.
    Otherwise userland has no signal that is needs to increase the size
    of its read buffer. From Roman Kapl.

12) Several XDP fixes for virtio_net, from Jesper Dangaard Brouer.

13) Module refcount leak in netlink when a dump start fails, from Jason
    Donenfeld.

14) Handle sub-optimal GSO sizes better in TCP BBR congestion control,
    from Eric Dumazet.

15) Releasing bpf per-cpu arraymaps can take a long time, add a
    condtional scheduling point. From Eric Dumazet.

16) Implement retpolines for tail calls in x64 and arm64 bpf JITs. From
    Daniel Borkmann.

17) Fix page leak in gianfar driver, from Andy Spencer.

18) Missed clearing of estimator scratch buffer, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net_sched: gen_estimator: fix broken estimators based on percpu stats
  gianfar: simplify FCS handling and fix memory leak
  ipv6 sit: work around bogus gcc-8 -Wrestrict warning
  macvlan: fix use-after-free in macvlan_common_newlink()
  bpf, arm64: fix out of bounds access in tail call
  bpf, x64: implement retpoline for tail call
  rxrpc: Fix send in rxrpc_send_data_packet()
  net: aquantia: Fix error handling in aq_pci_probe()
  bpf: fix rcu lockdep warning for lpm_trie map_free callback
  bpf: add schedule points in percpu arrays management
  regulatory: add NUL to request alpha2
  ibmvnic: Fix early release of login buffer
  net/smc9194: Remove bogus CONFIG_MAC reference
  net: ipv4: Set addr_type in hash_keys for forwarded case
  tcp_bbr: better deal with suboptimal GSO
  smsc75xx: fix smsc75xx_set_features()
  netlink: put module reference if dump start fails
  selftests/bpf/test_maps: exit child process without error in ENOMEM case
  selftests/bpf: update gitignore with test_libbpf_open
  selftests/bpf: tcpbpf_kern: use in6_* macros from glibc
  ..

Merge branch 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security

Pull security subsystem fixes from James Morris:

 - keys fixes via David Howells:
      "A collection of fixes for Linux keyrings, mostly thanks to Eric
       Biggers:

        - Fix some PKCS#7 verification issues.

        - Fix handling of unsupported crypto in X.509.

        - Fix too-large allocation in big_key"

 - Seccomp updates via Kees Cook:
      "These are fixes for the get_metadata interface that landed during
       -rc1. While the new selftest is strictly not a bug fix, I think
       it's in the same spirit of avoiding bugs"

 - an IMA build fix from Randy Dunlap

* 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  integrity/security: fix digsig.c build error with header file
  KEYS: Use individual pages in big_key for crypto buffers
  X.509: fix NULL dereference when restricting key with unsupported_sig
  X.509: fix BUG_ON() when hash algorithm is unsupported
  PKCS#7: fix direct verification of SignerInfo signature
  PKCS#7: fix certificate blacklisting
  PKCS#7: fix certificate chain verification
  seccomp: add a selftest for get_metadata
  ptrace, seccomp: tweak get_metadata behavior slightly
  seccomp, ptrace: switch get_metadata types to arch independent

Pull arm64 fixes from Catalin Marinas:
 "arm64 and perf fixes:

   - build error when accessing MPIDR_HWID_BITMASK from .S

   - fix CTR_EL0 field definitions

   - remove/disable some kernel messages on user faults (unhandled
     signals, unimplemented syscalls)

   - fix kernel page fault in unwind_frame() with function graph tracing

   - fix perf sleeping while atomic errors when booting with ACPI"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: fix unwind_frame() for filtered out fn for function graph tracing
  arm64: Enforce BBM for huge IO/VMAP mappings
  arm64: perf: correct PMUVer probing
  arm_pmu: acpi: request IRQs up-front
  arm_pmu: note IRQs and PMUs per-cpu
  arm_pmu: explicitly enable/disable SPIs at hotplug
  arm_pmu: acpi: check for mismatched PPIs
  arm_pmu: add armpmu_alloc_atomic()
  arm_pmu: fold platform helpers into platform code
  arm_pmu: kill arm_pmu_platdata
  ARM: ux500: remove PMU IRQ bouncer
  arm64: __show_regs: Only resolve kernel symbols when running at EL1
  arm64: Remove unimplemented syscall log message
  arm64: Disable unhandled signal log messages by default
  arm64: cpufeature: Fix CTR_EL0 field definitions
  arm64: uaccess: Formalise types for access_ok()
  arm64: Fix compilation error while accessing MPIDR_HWID_BITMASK from .S files

Pull MIPS fix from James Hogan:
 "A single MIPS fix for mismatching struct compat_flock, resulting in
  bus errors starting Firefox on Debian 8 since 4.13"

* tag 'mips_fixes_4.16_3' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
  MIPS: Drop spurious __unused in struct compat_flock

Pull printk fixlet from Petr Mladek:
 "People expect to see the real pointer value for %px.

  Let's substitute '(null)' only for the other %p? format modifiers that
  need to deference the pointer"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
  vsprintf: avoid misleading "(null)" for %px

Pull i2c fixes from Wolfram Sang:
 "Two bugfixes, one v4.16 regression fix, and two documentation fixes"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: designware: Consider SCL GPIO optional
  i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula".
  i2c: bcm2835: Set up the rising/falling edge delays
  i2c: i801: Add missing documentation entries for Braswell and Kaby Lake
  i2c: designware: must wait for enable

Pull SCSI fixes from James Bottomley:
 "These are mostly fixes for problems with merge window code.

  In addition we have one doc update (alua) and two dead code removals
  (aiclib and octogon) a spurious assignment removal (csiostor) and a
  performance improvement for storvsc involving better interrupt
  spreading and increasing the command per lun handling"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla4xxx: skip error recovery in case of register disconnect.
  scsi: aacraid: fix shutdown crash when init fails
  scsi: qedi: Cleanup local str variable
  scsi: qedi: Fix truncation of CHAP name and secret
  scsi: qla2xxx: Fix incorrect handle for abort IOCB
  scsi: qla2xxx: Fix double free bug after firmware timeout
  scsi: storvsc: Increase cmd_per_lun for higher speed devices
  scsi: qla2xxx: Fix a locking imbalance in qlt_24xx_handle_els()
  scsi: scsi_dh: Document alua_rtpg_queue() arguments
  scsi: Remove Makefile entry for oktagon files
  scsi: aic7xxx: remove aiclib.c
  scsi: qla2xxx: Avoid triggering undefined behavior in qla2x00_mbx_completion()
  scsi: mptfusion: Add bounds check in mptctl_hp_targetinfo()
  scsi: sym53c8xx_2: iterator underflow in sym_getsync()
  scsi: bnx2fc: Fix check in SCSI completion handler for timed out request
  scsi: csiostor: remove redundant assignment to pointer 'ln'
  scsi: ufs: Enable quirk to ignore sending WRITE_SAME command
  scsi: ibmvfc: fix misdefined reserved field in ibmvfc_fcp_rsp_info
  scsi: qla2xxx: Fix memory corruption during hba reset test
  scsi: mpt3sas: fix an out of bound write

For ages iproute2 has used `struct rtmsg` as the ancillary header for
FIB rules and in the process set the protocol value to RTPROT_BOOT.
Until ca56209a66 ("net: Allow a rule to track originating protocol")
the kernel rules code ignored the protocol value sent from userspace
and always returned 0 in notifications. To avoid incompatibility with
existing iproute2, send the protocol as a new attribute.

Fixes: cac56209 ("net: Allow a rule to track originating protocol")
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull drm fixes from Dave Airlie:
 "A bunch of fixes for rc3:

  Exynos:
   - fixes for using monotonic timestamps
   - register definitions
   - removal of unused file

  ipu-v3L
   - minor changes
   - make some register arrays const+static
   - fix some leaks

  meson:
   - fix for vsync

  atomic:
   - fix for memory leak

  EDID parser:
   - add quirks for some more non-desktop devices
   - 6-bit panel fix.

  drm_mm:
   - fix a bug in the core drm mm hole handling

  cirrus:
   - fix lut loading regression

  Lastly there is a deadlock fix around runtime suspend for secondary
  GPUs.

  There was a deadlock between one thread trying to wait for a workqueue
  job to finish in the runtime suspend path, and the workqueue job it
  was waiting for in turn waiting for a runtime_get_sync to return.

  The fixes avoids it by not doing the runtime sync in the workqueue as
  then we always wait for all those tasks to complete before we runtime
  suspend"

* tag 'drm-fixes-for-v4.16-rc3' of git://people.freedesktop.org/~airlied/linux: (25 commits)
  drm/tve200: fix kernel-doc documentation comment include
  drm/edid: quirk Sony PlayStation VR headset as non-desktop
  drm/edid: quirk Windows Mixed Reality headsets as non-desktop
  drm/edid: quirk Oculus Rift headsets as non-desktop
  drm/meson: fix vsync buffer update
  drm: Handle unexpected holes in color-eviction
  drm: exynos: Use proper macro definition for HDMI_I2S_PIN_SEL_1
  drm/exynos: remove exynos_drm_rotator.h
  drm/exynos: g2d: Delete an error message for a failed memory allocation in two functions
  drm/exynos: fix comparison to bitshift when dealing with a mask
  drm/exynos: g2d: use monotonic timestamps
  drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA
  gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg
  gpu: ipu-cpmem: add 16-bit grayscale support to ipu_cpmem_set_image
  gpu: ipu-v3: prg: fix device node leak in ipu_prg_lookup_by_phandle
  gpu: ipu-v3: pre: fix device node leak in ipu_pre_lookup_by_phandle
  drm/amdgpu: Fix deadlock on runtime suspend
  drm/radeon: Fix deadlock on runtime suspend
  drm/nouveau: Fix deadlock on runtime suspend
  drm: Allow determining if current task is output poll worker
  ...

The packet fanout test generates UDP traffic and reads this with
a pair of packet sockets, testing the various fanout algorithms.

Avoid non-determinism from reading unrelated background traffic.
Fanout decisions are made before unrelated packets can be dropped with
a filter, so that is an insufficient strategy [*]. Run the packet
socket tests in a network namespace, similar to msg_zerocopy.

It it still good practice to install a filter on a packet socket
before accepting traffic. Because this is example code, demonstrate
that pattern. Open the socket initially bound to no protocol, install
a filter, and only then bind to ETH_P_IP.

Another source of non-determinism is hash collisions in FANOUT_HASH.
The hash function used to select a socket in the fanout group includes
the pseudorandom number hashrnd, which is not visible from userspace.
To work around this, the test tries to find a pair of UDP source ports
that do not collide. It gives up too soon (5 times, every 32 runs) and
output is confusing. Increase tries to 20 and revise the error msg.

[*] another approach would be to add a third socket to the fanout
    group and direct all unexpected traffic here. This is possible
    only when reimplementing methods like RR or HASH alongside this
    extra catch-all bucket, using the BPF fanout method.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Zero is being bit-wise or'd in a calculation twice; these are redundant
and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pfifo_fast got percpu stats lately, uncovering a bug I introduced last
year in linux-4.10.

I missed the fact that we have to clear our temporary storage
before calling __gnet_stats_copy_basic() in the case of percpu stats.

Without this fix, rate estimators (tc qd replace dev xxx root est 1sec
4sec pfifo_fast) are utterly broken.

Fixes: 1c0d32fd ("net_sched: gen_estimator: complete rewrite of rate estimators")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2018-02-22

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) two urgent fixes for bpf_tail_call logic for x64 and arm64 JITs, from Daniel.

2) cond_resched points in percpu array alloc/free paths, from Eric.

3) lockdep and other minor fixes, from Yonghong, Arnd, Anders, Li.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

if either or both of MSG_ZEROCOPY and SOCK_ZEROCOPY have not been
specified, the rm->data.op_mmp_znotifier allocation will be skipped.
In this case, it is invalid ot pass down a cmsghdr with
RDS_CMSG_ZCOPY_COOKIE, so return EINVAL from rds_msg_zcopy for this
case.

Reported-by: syzbot+f893ae7bb2f6456dfbc3@syzkaller.appspotmail.com
Fixes: 0cebacce ("rds: zerocopy Tx support.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8168_check_dash() returns false anyway for all chip versions not
supporting dash. So we can simplify the check conditions.

In addition change the check functions to return bool instead of int,
because they actually return a bool value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, if BIOS enables WOL in the chip, settings are inconsistent
because the device isn't marked as wakeup-enabled (if not done
explicitly via userspace tools). This causes issues with suspend/
resume because mdio_bus_phy_may_suspend() checks whether device is
wakeup-enabled. In detail MDIO bus access in phy_suspend() can fail
because the MDIO bus is disabled.

In the history of the driver we find two competing approaches:
8f9d5138 "r8169: remember WOL preferences on driver load" prefers
to preserve what the BIOS may have set, whilst bde135a6
"r8169: only enable PCI wakeups when WOL is active" disabled PCI
wakeup per default to work around a bug on one platform.

Seems like nobody complained after the latter patch about non-working
WOL, what makes me think that nobody uses WOL w/o configuring it
explicitly.

My opinion:
Vast majority of users doesn't use WOL even if the BIOS enables it in
the chip. And having WOL being active keeps the PHY(s) from powering
down if being idle.
If somebody needs WOL, he can enable it during boot, e.g. by
configuring systemd.link/WakeOnLan.

Therefore, to make WOL consistent again, disable it per default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.

Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: Jim Gruen <jgruen@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gcc-8 has a new warning that detects overlapping input and output arguments
in memcpy(). It triggers for sit_init_net() calling ipip6_tunnel_clone_6rd(),
which is actually correct:

net/ipv6/sit.c: In function 'sit_init_net':
net/ipv6/sit.c:192:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]

The problem here is that the logic detecting the memcpy() arguments finds them
to be the same, but the conditional that tests for the input and output of
ipip6_tunnel_clone_6rd() to be identical is not a compile-time constant.

We know that netdev_priv(t->dev) is the same as t for a tunnel device,
and comparing "dev" directly here lets the compiler figure out as well
that 'dev == sitn->fb_tunnel_dev' when called from sit_init_net(), so
it no longer warns.

This code is old, so Cc stable to make sure that we don't get the warning
for older kernels built with new gcc.

Cc: Martin Sebor <msebor@gmail.com>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83456Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following use-after-free was reported by KASan when running
LTP macvtap01 test on 4.16-rc2:

[10642.528443] BUG: KASAN: use-after-free in
               macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10642.626607] Read of size 8 at addr ffff880ba49f2100 by task ip/18450
...
[10642.963873] Call Trace:
[10642.994352]  dump_stack+0x5c/0x7c
[10643.035325]  print_address_description+0x75/0x290
[10643.092938]  kasan_report+0x28d/0x390
[10643.137971]  ? macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.207963]  macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.275978]  macvtap_newlink+0x171/0x260 [macvtap]
[10643.334532]  rtnl_newlink+0xd4f/0x1300
...
[10646.256176] Allocated by task 18450:
[10646.299964]  kasan_kmalloc+0xa6/0xd0
[10646.343746]  kmem_cache_alloc_trace+0xf1/0x210
[10646.397826]  macvlan_common_newlink+0x6de/0x14a0 [macvlan]
[10646.464386]  macvtap_newlink+0x171/0x260 [macvtap]
[10646.522728]  rtnl_newlink+0xd4f/0x1300
...
[10647.022028] Freed by task 18450:
[10647.061549]  __kasan_slab_free+0x138/0x180
[10647.111468]  kfree+0x9e/0x1c0
[10647.147869]  macvlan_port_destroy+0x3db/0x650 [macvlan]
[10647.211411]  rollback_registered_many+0x5b9/0xb10
[10647.268715]  rollback_registered+0xd9/0x190
[10647.319675]  register_netdevice+0x8eb/0xc70
[10647.370635]  macvlan_common_newlink+0xe58/0x14a0 [macvlan]
[10647.437195]  macvtap_newlink+0x171/0x260 [macvtap]

Commit d02fd6e7 ("macvlan: Fix one possible double free") handles
the case when register_netdevice() invokes ndo_uninit() on error and
as a result free the port. But 'macvlan_port_get_rtnl(dev))' check
(returns dev->rx_handler_data), which was added by this commit in order
to prevent double free, is not quite correct:

* for macvlan it always returns NULL because 'lowerdev' is the one that
  was used to register rx handler (port) in macvlan_port_create() as
  well as to unregister it in macvlan_port_destroy().
* for macvtap it always returns a valid pointer because macvtap registers
  its own rx handler before macvlan_common_newlink().

Fixes: d02fd6e7 ("macvlan: Fix one possible double free")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk is already allocated in inet_create/inet6_create, hence when
BPF_CGROUP_RUN_PROG_INET_SOCK is executed sk will never be NULL.

The logic is as bellow,
	sk = sk_alloc();
	if (!sk)
		goto out;
	BPF_CGROUP_RUN_PROG_INET_SOCK(sk);
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

do_task_stat() calls get_wchan(), which further does unwind_frame().
unwind_frame() restores frame->pc to original value in case function
graph tracer has modified a return address (LR) in a stack frame to hook
a function return. However, if function graph tracer has hit a filtered
function, then we can't unwind it as ftrace_push_return_trace() has
biased the index(frame->graph) with a 'huge negative'
offset(-FTRACE_NOTRACE_DEPTH).

Moreover, arm64 stack walker defines index(frame->graph) as unsigned
int, which can not compare a -ve number.

Similar problem we can have with calling of walk_stackframe() from
save_stack_trace_tsk() or dump_backtrace().

This patch fixes unwind_frame() to test the index for -ve value and
restore index accordingly before we can restore frame->pc.

Reproducer:

cd /sys/kernel/debug/tracing/
echo schedule > set_graph_notrace
echo 1 > options/display-graph
echo wakeup > current_tracer
ps -ef | grep -i agent

Above commands result in:
Unable to handle kernel paging request at virtual address ffff801bd3d1e000
pgd = ffff8003cbe97c00
[ffff801bd3d1e000] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000006 [#1] SMP
[...]
CPU: 5 PID: 11696 Comm: ps Not tainted 4.11.0+ #33
[...]
task: ffff8003c21ba000 task.stack: ffff8003cc6c0000
PC is at unwind_frame+0x12c/0x180
LR is at get_wchan+0xd4/0x134
pc : [<ffff00000808892c>] lr : [<ffff0000080860b8>] pstate: 60000145
sp : ffff8003cc6c3ab0
x29: ffff8003cc6c3ab0 x28: 0000000000000001
x27: 0000000000000026 x26: 0000000000000026
x25: 00000000000012d8 x24: 0000000000000000
x23: ffff8003c1c04000 x22: ffff000008c83000
x21: ffff8003c1c00000 x20: 000000000000000f
x19: ffff8003c1bc0000 x18: 0000fffffc593690
x17: 0000000000000000 x16: 0000000000000001
x15: 0000b855670e2b60 x14: 0003e97f22cf1d0f
x13: 0000000000000001 x12: 0000000000000000
x11: 00000000e8f4883e x10: 0000000154f47ec8
x9 : 0000000070f367c0 x8 : 0000000000000000
x7 : 00008003f7290000 x6 : 0000000000000018
x5 : 0000000000000000 x4 : ffff8003c1c03cb0
x3 : ffff8003c1c03ca0 x2 : 00000017ffe80000
x1 : ffff8003cc6c3af8 x0 : ffff8003d3e9e000

Process ps (pid: 11696, stack limit = 0xffff8003cc6c0000)
Stack: (0xffff8003cc6c3ab0 to 0xffff8003cc6c4000)
[...]
[<ffff00000808892c>] unwind_frame+0x12c/0x180
[<ffff000008305008>] do_task_stat+0x864/0x870
[<ffff000008305c44>] proc_tgid_stat+0x3c/0x48
[<ffff0000082fde0c>] proc_single_show+0x5c/0xb8
[<ffff0000082b27e0>] seq_read+0x160/0x414
[<ffff000008289e6c>] __vfs_read+0x58/0x164
[<ffff00000828b164>] vfs_read+0x88/0x144
[<ffff00000828c2e8>] SyS_read+0x60/0xc0
[<ffff0000080834a0>] __sys_trace_return+0x0/0x4

Fixes: 20380bb3 (arm64: ftrace: fix a stack tracer's output under function graph tracer)
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
[catalin.marinas@arm.com: replace WARN_ON with WARN_ON_ONCE]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

security/integrity/digsig.c has build errors on some $ARCH due to a
missing header file, so add it.

  security/integrity/digsig.c:146:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: linux-integrity@vger.kernel.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/Signed-off-by: James Morris <james.morris@microsoft.com>

Merge tag 'keys-fixes-20180222-2' of https://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into fixes-v4.16-rc3

Keyrings fixes.

drm/imx: ipu-v3 fixups and grayscale support

- Make const interrupt register arrays static, reduces object size.
- Fix device_node leaks in PRE/PRG phandle lookup functions.
- Add 8-bit and 16-bit grayscale buffer support to ipu_cpmem_set_image,
- add 10-bit and 12-bit grayscale media bus support to ipu-csi,
  to be used by the imx-media driver.

* tag 'imx-drm-next-2018-02-22' of git://git.pengutronix.de/git/pza/linux:
  gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg
  gpu: ipu-cpmem: add 16-bit grayscale support to ipu_cpmem_set_image
  gpu: ipu-v3: prg: fix device node leak in ipu_prg_lookup_by_phandle
  gpu: ipu-v3: pre: fix device node leak in ipu_pre_lookup_by_phandle
  gpu: ipu-cpmem: add 8-bit grayscale support to ipu_cpmem_set_image
  gpu: ipu-v3: make const arrays int_reg static, shrinks object size

The MIPS %.its.S compiler command did not define __ASSEMBLY__, which meant
when compiler_types.h was added to kconfig.h, unexpected things appeared
(e.g. struct declarations) which should not have been present. As done in
the general %.S compiler command, __ASSEMBLY__ is now included here too.

The failure was:

    Error: arch/mips/boot/vmlinux.gz.its:201.1-2 syntax error
    FATAL ERROR: Unable to parse input tree
    /usr/bin/mkimage: Can't read arch/mips/boot/vmlinux.gz.itb.tmp: Invalid argument
    /usr/bin/mkimage Can't add hashes to FIT blob
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 28128c61 ("kconfig.h: Include compiler types to avoid missed struct attributes")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace

Pull siginfo fix from Eric Biederman:
 "This fixes a build error that only shows up on blackfin"

* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  fs/signalfd: fix build error for BUS_MCEERR_AR

Pull crypto fix from Herbert Xu:
 "Fix an oops in the s5p-sss driver when used with ecb(aes)"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: s5p-sss - Fix kernel Oops in AES-ECB mode