When receiving failed PLCP frames is enabled, there
won't be a rate pointer when we add the radiotap
header and thus the kernel will crash. Fix this by
not assuming the rate pointer is always valid. It's
still always valid for frames that have good PLCP
though, and that is checked & enforced.

This was broken by my
commit fc885189
Author: Johannes Berg <johannes.berg@intel.com>
Date:   Fri Jul 30 13:23:12 2010 +0200

    mac80211: don't check rates on PLCP error frames

where I removed the check in this case but didn't
take into account that the rate info would be used.
Reported-by: Xiaokang Qin <xiaokang.qin@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A minor fix for the check that verifies that all given SSIDs (in req) exist
in the filters (the match sets)
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This happens with devices using a regulatory domain 0x68 that are only
5Ghz capable because ath_reg_apply_active_scan_flags assumes that we
always have a 2,4Ghz band.

CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 82cd838c, ra == 82cd8384
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000061 00000003 00000024
$ 4 : 00000003 000016c1 82f900ac 00000024
$ 8 : 00000000 82cda304 0058bad8 00000005
$12 : 005908f8 001e8481 00000003 1dcd6500
$16 : 00000002 00000000 82c700c0 82c700c0
$20 : 82d415e4 82c70d64 82c70200 82c715bc
$24 : 00000000 11e1a300
$28 : 82ce2000 82ce3c70 82c715a8 82cd8384
Hi : 00000000
Lo : 0000001e
epc : 82cd838c ath_reg_apply_world_flags+0x78/0x17c [ath]
Not tainted
ra : 82cd8384 ath_reg_apply_world_flags+0x70/0x17c [ath]
Status: 1000d403 KERNEL EXL IE
Cause : 80800008
BadVA : 00000000
PrId : 00019374 (MIPS 24Kc)
Modules linked in: ath9k(+) ath9k_common ath9k_hw ath mac80211 cfg80211
	compat_firmware_class compat arc4 aes_generic deflate ecb cbc
	leds_gpio button_hotplug gpio_buttons input_polldev ie
Process insmod (pid: 464, threadinfo=82ce2000, task=838b31d8, tls=00000000)
Stack : 00000000 00000002 82f900ac 82c700c0 82d415e4 82c70d64 00000000 00000068
82f900ac 82cd88f4 82c700c0 82cda304 00000001 000020f0 82f90000 82c70d40
00000002 82f90000 82f900ac 82d4207c 82d518a0 00000002 7fee6118 8017c0d8
00000008 8397ba00 82c70d40 00000000 82c70200 83813000 83813058 b0010000
82d518a0 00000002 7fee6118 82d4b8c8 83445cc0 80120dc0 83804000 800eeda0
...
Call Trace:
[<82cd838c>] ath_reg_apply_world_flags+0x78/0x17c [ath]
[<82cd88f4>] ath_regd_init+0x464/0x488 [ath]
[<82d4207c>] ath9k_init_device+0x6a4/0x6b4 [ath9k]
[<82d4b8c8>] ath_pci_probe+0x27c/0x358 [ath9k]
[<80181de0>] pci_device_probe+0x64/0xa4
[<8019e874>] driver_probe_device+0xb8/0x190
[<8019e9b8>] __driver_attach+0x6c/0xa4
[<8019dfc0>] bus_for_each_dev+0x60/0xb0
[<8019d744>] bus_add_driver+0xc4/0x25c
[<8019ed6c>] driver_register+0xe0/0x198
[<8018206c>] __pci_register_driver+0x50/0xe0
[<82dd0010>] ath9k_init+0x10/0x54 [ath9k]
[<8006b4a0>] do_one_initcall+0x68/0x1ec
[<800a901c>] sys_init_module+0xec/0x23c
[<80062544>] stack_done+0x20/0x3c
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Two new struct members were not documented, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since this device declares itself as vendor specific, must add
a new entry to device ID table to support it.

usb-device output of this device:

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=413c ProdID=8197 Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=D0DF9AA9C9F1
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Timers set by __set_chan_timer() should use miliseconds instead of
jiffies. Commit 942ecc9c updated
l2cap_set_timer() so it expects timeout to be specified in msecs
instead of jiffies. This makes timeouts unreliable when CONFIG_HZ
is not set to 1000.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This reverts commit 33060542.
The commit introduces regression when two 2.1 devices attempt
establish rfcomm channel. Such connection is refused since there's
a security block issue on l2cap. It means the link is unencrypted.

2011-09-16 18:08:46.567616 < ACL data: handle 1 flags 0x00 dlen 24
    0000: 14 00 40 00 06 00 02 00  0f 35 03 19 12 00 ff ff
..@......5....˙˙
    0010: 35 05 0a 00 00 ff ff 00                           5....˙˙.
2011-09-16 18:08:46.572377 > HCI Event: Number of Completed Packets
(0x13) plen 5
    handle 1 packets 1
2011-09-16 18:08:46.577931 > ACL data: handle 1 flags 0x02 dlen 88
    L2CAP(d): cid 0x0040 len 84 [psm 0]
      0000: 07 00 02 00 4f 00 4c 35  4a 35 48 09 00 00 0a 00
....O.L5J5H.....
      0010: 01 00 00 09 00 01 35 03  19 12 00 09 00 05 35 03
......5.......5.
      0020: 19 10 02 09 00 09 35 08  35 06 19 12 00 09 01 02
......5.5.......
      0030: 09 02 00 09 01 02 09 02  01 09 00 0a 09 02 02 09
................
      0040: 00 00 09 02 03 09 00 00  09 02 04 28 01 09 02 05
...........(....
      0050: 09 00 02 00                                       ....
2011-09-16 18:08:46.626057 < HCI Command: Authentication Requested
(0x01|0x0011) plen 2
    handle 1
2011-09-16 18:08:46.627614 > HCI Event: Command Status (0x0f) plen 4
    Authentication Requested (0x01|0x0011) status 0x00 ncmd 1
2011-09-16 18:08:46.627675 > HCI Event: Link Key Request (0x17) plen 6
    bdaddr 00:00:F2:6A:29:69
2011-09-16 18:08:46.634999 < HCI Command: Link Key Request Reply
(0x01|0x000b) plen 22
    bdaddr 00:00:F2:6A:29:69 key 58CD393179FC902E5E8F512A855EE532
2011-09-16 18:08:46.683278 > HCI Event: Command Complete (0x0e) plen 10
    Link Key Request Reply (0x01|0x000b) ncmd 1
    status 0x00 bdaddr 00:00:F2:6A:29:69
2011-09-16 18:08:46.764729 > HCI Event: Auth Complete (0x06) plen 3
    status 0x00 handle 1
2011-09-16 18:08:46.764821 < ACL data: handle 1 flags 0x00 dlen 12
    0000: 08 00 01 00 02 05 04 00  03 00 41 00              ..........A.
2011-09-16 18:08:46.764851 > HCI Event: Command Status (0x0f) plen 4
    Unknown (0x00|0x0000) status 0x00 ncmd 2
2011-09-16 18:08:46.768117 > HCI Event: Number of Completed Packets
(0x13) plen 5
    handle 1 packets 1
2011-09-16 18:08:46.770894 > ACL data: handle 1 flags 0x02 dlen 16
    L2CAP(s): Connect rsp: dcid 0x0000 scid 0x0041 result 3 status 0
      Connection refused - security block
2011-09-16 18:08:49.000691 < ACL data: handle 1 flags 0x00 dlen 12
    0000: 08 00 01 00 06 06 04 00  40 00 40 00              ........@.@.
2011-09-16 18:08:49.015675 > HCI Event: Number of Completed Packets
(0x13) plen 5
    handle 1 packets 1
2011-09-16 18:08:49.016927 > ACL data: handle 1 flags 0x02 dlen 12
    L2CAP(s): Disconn rsp: dcid 0x0040 scid 0x0040
2011-09-16 18:08:51.009480 < HCI Command: Disconnect (0x01|0x0006) plen
3
    handle 1 reason 0x13
    Reason: Remote User Terminated Connection
2011-09-16 18:08:51.011525 > HCI Event: Command Status (0x0f) plen 4
    Disconnect (0x01|0x0006) status 0x00 ncmd 1
2011-09-16 18:08:51.123494 > HCI Event: Disconn Complete (0x05) plen 4
    status 0x00 handle 1 reason 0x16
    Reason: Connection Terminated by Local Host
Signed-off-by: Arek Lichwa <arkadiusz.lichwa@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Set IEEE80211_FCTL_MOREDATA bit also in case we have buffered
frames (more than one) only for one AC.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If kmemdup() fails we leak the memory allocated to bss_desc.
This patch fixes the leak.
I also removed the pointless default assignment of 'NULL' to 'bss_desc'
while I was there anyway.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When comparing two items by IE, the sort order
wasn't stable, which could lead to issues in the
rbtree. Make it stable by making a missing IE
sort before a present IE.

Also sort by length first if it differs and then
by contents.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In other modes the parameters should not be set.
Right now, mac80211 will set them, even if the
user asked for setting them on VLANs which the
driver doesn't know about, causing all kinds of
trouble.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Since the NL80211_ATTR_HT_CAPABILITY attribute is
used as a struct, it needs a minimum, not maximum
length. Enforce that properly. Not doing so could
potentially lead to reading after the buffer.

Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some buggy APs (and even P2P_GO) don't advertise their
basic rates in the association response.

In such case, use the min supported rate as the
basic rate.
Reported-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Though it's unlikely, di may be null, so we can't dereference
di->dma.dmactrlflags until we've checked it.

Move this de-reference after the check, and adjust the error
message to not require de-referencing di.

This is based upon Julia's original patch:
<1319846297-2985-2-git-send-email-julia@diku.dk>
Reported-by: Julia Lawall <julia@diku.dk>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes PHY transmission errors reported on some LP-PHY and HT-PHY
cards. For LP-PHY they were quite rare and not really noticable. On
HT-PHY they were critical, OFDM rates were not available at all.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The warning really shouldn't happen, but until we
find the reason why it does don't spew it all the
time, just once is enough to know we've hit it.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Perform "echo test" when cmd queue stuck detected, somethime it will cause
calltrace. I am not sure how to fix it yet, just remove the action now until
find a better way to handle it.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver can spam the logs with "RX: Packet dropped" messages. These drops
originate from 1. a correpted PLCP, 2. decryption errors, and 3. packet
size underruns. Condition #3 logs a separate message, thus no dropped message
is needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Only AID values 1-2007 are valid, but some APs have been
found to send random bogus values, in the reported case an
AP that was sending the AID field value 0xffff, an AID of
0x3fff (16383).

There isn't much we can do but disable powersave since
there's no way it can work properly in this case.

Cc: stable@vger.kernel.org
Reported-by: Bill C Riemers <briemers@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Continue the init process even fail to enable msi

out_iounmap is no longer used, remove it
Reported-by: werner <w.landgraf@ru.ru>
Tested-by: werner <w.landgraf@ru.ru>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 2e30168b ("libertas: terminate scan when stopping interface")
adds cleanup code to lbs_eth_stop to call cfg80211_scan_done if there's
an outstanding cfg80211_scan_request.  However, it assumes that the
scan request was allocated via the cfg80211 stack.  Libertas has
its own internal allocation method, kept track of with
priv->internal_scan.  This doesn't set scan_req->wiphy, amongst other
things, which results in hitting a BUG() when we call cfg80211_scan_done
on the request.

This provides a function to take care of the low-level scan_req cleanup
details.  We simply call that to deal with finishing up scan requests.

The bug we were hitting was:

[  964.321495] kernel BUG at net/wireless/core.h:87!
[  964.329970] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[  964.341963] pgd = dcf80000
...
[  964.849998] 9fe0: 00000000 beb417b8 4018e280 401e822c 60000010 00000004 00000000 00000000
[  964.865007] [<c003104c>] (__bug+0x1c/0x28) from [<c0384ffc>] (cfg80211_scan_done+0x54/0x6c)
[  964.895324] [<c0384ffc>] (cfg80211_scan_done+0x54/0x6c) from [<bf028bac>] (lbs_eth_stop+0x10c/0x188 [libertas])
[  964.895324] [<bf028bac>] (lbs_eth_stop+0x10c/0x188 [libertas]) from [<c03002a0>] (__dev_close_many+0x94/0xc4)
[  964.918995] [<c03002a0>] (__dev_close_many+0x94/0xc4) from [<c030037c>] (dev_close_many+0x78/0xe0)
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

During the fast channel change noise floor values are being loaded
twice at init_cal and after channel_change. The commit "ath9k_hw:
Improve fast channel change for AR9003 chips" overlooked it that
caused failure to load nf while doing bgscan. This patch performs noise
floor calibration after the fast and full reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes system hang when resuming from S3 state
and lower rate sens failure issue.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We need to verify whether the command is successful before allocating
the station entry to avoid extra processing. This also fixes a memory
leak on the error path.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Previously the driver did not care if TX_CTL_REQ_TX_STATUS
was set on aggregated frames or not and it would silently
drop successfully sent frames if possible [much like:
"no news is good news!"].

But, TX_CTL_REQ_TX_STATUS was invented for a reason and
no tx status report should ever be dropped if it is set.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The commit ce407afc introduced regression for AR9330/AR9340
register offsets. Some of the register offsets are common
for AR9330/AR9340/AR9485 except AR9380. Fix that.

Cc: stable@kernel.org [3.1.0+]
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When going back on-channel, we should reconfigure
the hw iff the hardware is not already configured
to the operational channel.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The offchannel code is currently broken - we should
remain_off_channel if the work was started, and
the work's channel and channel_type are the same
as local->tmp_channel and local->tmp_channel_type.

However, if wk->chan_type and local->tmp_channel_type
coexist (e.g. have the same channel type), we won't
remain_off_channel.

This behavior was introduced by commit da2fd1f0
("mac80211: Allow work items to use existing
channel type.")
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: John W. Linville <linville@tuxdriver.com>

IQ calibration during fast channel change sometimes failed
with RTT. And also restoring invalid radio retention readings
during init cal could cause failure to set the channel properly.
This patch counts the valid rtt history readings and clears
rtt mask.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

My recent commits (3782c69d, 324c74ad) introduced regression
for register offset selection that based on the macversion.
Not using parentheses in proper manner for ternary operator
leads to select wrong offset for the registers.

This issue was observed with AR9462 chip that immediate disconnect
after the association with the following message

ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47
after 500ms, disconnecting.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As Stanislaw pointed out, my patch

	iwlagn: fix a race in the unmapping of the TFDs

solved only part of the problem. The race still exists for TFDs of
the host commands. Fix that too.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When loading the usb-configuration we do not signal the end of configuration on
memory allocation error. This patch moves the memory allocation to the top so
every error path uses "goto error" now to correctly send the usb-ctrl message
when detecting some error.

This also replaces GFP_ATOMIC with GFP_KERNEL as we are allowed to sleep here.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

A workqueue is allowed to sleep so we can safely use GFP_KERNEL instead of
GFP_ATOMIC. This is still legacy code when the driver used timer BHs and not a
worqueue.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

When disconnecting a bcm203x device we kill and destroy the usb-urb, however,
there might still be a pending work-structure which resubmits the now invalid
urb. To avoid this race condition, we simply set a shutdown-flag and
synchronously kill the worker first.

This also adds a comment to all schedule_work()s, as it is really not clear
that they are used as replacement for short timers (which can be seen in the git
history).
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

We are allowed to sleep here so no need to use GFP_ATOMIC. The caller
(ath3k_probe) calls request_firmware() which definitely sleeps. Hence, we should
avoid using GFP_ATOMIC.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

The HCI_MGMT flag should only be set when user space requests the full
controller information. This way we avoid potential issues with setting
change events ariving before the actual read_controller_info command
finishes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

I've noticed that my CSR usb dongle was not working if it was plugged in when
PC was booting. It looks like I get two HCI reset command complete events (see
hcidump logs below).
The root cause is reset called from off_timer. Timeout for this reset to
complete is set to 250ms and my bt dongle requires more time for replying with
command complete event. After that, chip seems to reply with reset command
complete event for next non-reset command.

Attached patch increase mentioned timeout to HCI_INIT_TIMEOUT, this value is
already used for timeouting hci_reset_req in hci_dev_reset().

This might also be related to BT not working after suspend that was reported
here some time ago.

Hcidump log:

2011-09-12 23:13:27.379465 < HCI Command: Reset (0x03|0x0003) plen 0
2011-09-12 23:13:27.380797 > HCI Event: Command Complete (0x0e) plen 4
    Reset (0x03|0x0003) ncmd 1
    status 0x00
2011-09-12 23:13:27.380859 < HCI Command: Read Local Supported Features (0x04|0x000
3) plen 0
2011-09-12 23:13:27.760789 > HCI Event: Command Complete (0x0e) plen 4
    Reset (0x03|0x0003) ncmd 1
    status 0x00
2011-09-12 23:13:27.760831 < HCI Command: Read Local Version Information (0x04|0x00
01) plen 0
2011-09-12 23:13:27.764780 > HCI Event: Command Complete (0x0e) plen 12
    Read Local Version Information (0x04|0x0001) ncmd 1
    status 0x00
    HCI Version: 1.1 (0x1) HCI Revision: 0x36f
    LMP Version: 1.1 (0x1) LMP Subversion: 0x36f
    Manufacturer: Cambridge Silicon Radio (10)
Signed-off-by: Szymon Janc <szymon@janc.net.pl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>