Do a couple of changes for when HISI_SAS_RESET_BIT is set for HBA:

 - Clearing ITCT is not necessary

 - Remove internal abort as it will fail during reset

Flag sas_dev->dev_type is kept as SAS_PHY_UNUSED.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch do following optimizations to host controller reset:

1. Unblock scsi requests before rescanning topology, as SCSI command need be
   used if new device is found during rescanning topology.

2. Remove drain_workqueue(hisi_hba->wq) and drain_workqueue(shost->work_q), as
   there is no need to ensure that all PHYs event are done before exiting host
   reset.

3. Improve message print level of host reset. Host reset is an important and
   very few occurrence event. We should know its progress even when not
   debugging.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Currently refreshing the PHY port id after reset is done in the rescan
topology function, which is quite late in the reset process. It could be moved
earlier in the process, as the port id can be refreshed once the PHYs become
ready.

In addition to this, we should set the hisi_sas_dev port id to 0xff (invalid
port id) if all PHYs of this port remain down for the same device.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In certain scenarios we may just want to clear the ITCT for a device, and not
free other resources like the SATA bitmap using in v2 hw.

To facilitate this, this patch relocates the code of clearing ITCT from
free_device() to a new hw interface clear_itct().  Then for some hw, we should
not realise free_device() if there's nothing left to do for it.

[mkp: typo]
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

For function dma_unmap_sg(), the <nents> parameter should be number of
elements in the scatterlist prior to the mapping, not after the mapping.

Fix this usage.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

It is required to initialize the dq spinlock before use, which was not being
done, so fix it. This issue can be detected when CONFIG_DEBUG_SPINLOCK is
enabled.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

These duplicate includes have been found with scripts/checkincludes.pl
but they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Avoid that building with gcc 7 and W=1 triggers warnings similar to the
following:

drivers/scsi/qla2xxx/qla_isr.c:1189:27: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Quinn Tran <quinn.tran@cavium.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

fnic_fcpio_icmnd_cmpl_handler() displays the value of sc with:

    FNIC_SCSI_DBG(KERN_INFO...
        "... sc = 0x%p"
        "scsi_status ..."
        ...

As the literal strings get merged, the function uses %ps instead of the
intended raw %p format. Fix this by inserting a space.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add exported functions from scsi_common.c to the SCSI driver API
documentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Clean up some comment typos and fix some errors in documentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The check for secs being less than zero is redundant for two reasons.
Firstly, secs is unsigned so the check is always going to be false.
Secondly, if secs was signed the proceeding calculation of secs is never
going to be negative.  Hence we can remove this redundant check and day
and secs re-adjustment.

Detected by static analysis with smatch:
arcmsr_set_iop_datetime() warn: unsigned 'secs' is never less than zero.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ching Huang <ching2048@areca.com.tw>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The bfa driver has a number of real issues with string termination
that gcc-8 now points out:

drivers/scsi/bfa/bfad_bsg.c: In function 'bfad_iocmd_port_get_attr':
drivers/scsi/bfa/bfad_bsg.c:320:9: error: argument to 'sizeof' in 'strncpy' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_psymb_init':
drivers/scsi/bfa/bfa_fcs.c:775:9: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:781:9: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:788:9: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:801:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:808:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_nsymb_init':
drivers/scsi/bfa/bfa_fcs.c:837:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:844:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c:852:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_psymb_init':
drivers/scsi/bfa/bfa_fcs.c:778:2: error: 'strncat' output may be truncated copying 10 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:784:2: error: 'strncat' output may be truncated copying 30 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:803:3: error: 'strncat' output may be truncated copying 44 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:811:3: error: 'strncat' output may be truncated copying 16 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c: In function 'bfa_fcs_fabric_nsymb_init':
drivers/scsi/bfa/bfa_fcs.c:840:2: error: 'strncat' output may be truncated copying 10 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs.c:847:2: error: 'strncat' output may be truncated copying 30 bytes from a string of length 63 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_fdmi_get_hbaattr':
drivers/scsi/bfa/bfa_fcs_lport.c:2657:10: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs_lport.c:2659:11: error: argument to 'sizeof' in 'strncat' call is the same expression as the source; did you mean to use the size of the destination? [-Werror=sizeof-pointer-memaccess]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_lport_ms_gmal_response':
drivers/scsi/bfa/bfa_fcs_lport.c:3232:5: error: 'strncpy' output may be truncated copying 16 bytes from a string of length 247 [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_lport_ns_send_rspn_id':
drivers/scsi/bfa/bfa_fcs_lport.c:4670:3: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c:4682:3: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_lport_ns_util_send_rspn_id':
drivers/scsi/bfa/bfa_fcs_lport.c:5206:3: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c:5215:3: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcs_lport.c: In function 'bfa_fcs_fdmi_get_portattr':
drivers/scsi/bfa/bfa_fcs_lport.c:2751:2: error: 'strncpy' specified bound 128 equals destination size [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcbuild.c: In function 'fc_rspnid_build':
drivers/scsi/bfa/bfa_fcbuild.c:1254:2: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]
drivers/scsi/bfa/bfa_fcbuild.c:1253:25: note: length computed here
drivers/scsi/bfa/bfa_fcbuild.c: In function 'fc_rsnn_nn_build':
drivers/scsi/bfa/bfa_fcbuild.c:1275:2: error: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation]

In most cases, this can be addressed by correctly calling strlcpy and
strlcat instead of strncpy/strncat, with the size of the destination
buffer as the last argument.

For consistency, I'm changing the other callers of strncpy() in this
driver the same way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Although it is important to be able to trigger the code in the SCSI core
for SCSI_MLQUEUE_HOST_BUSY handling, currently it is nontrivial to
trigger that code. Hence this patch that adds a new error injection
option to the scsi_debug driver for making the .queue_rq()
implementation of this driver return SCSI_MLQUEUE_HOST_BUSY.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The Dell PV650F is a re-branded CLARiiON FC5700.  And DGC/RAID,DISK
identifies all CLARiiON family.

Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add IBM 3542 and 3552, arrays: FAStT200 and FAStT500.

Add full STK OPENstorage family, arrays: 9176, D173, D178, D210, D220,
D240 and D280.

Add STK BladeCtlr family, arrays: B210, B220, B240 and B280.

These changes were done in multipath-tools time ago.

Cc: NetApp RDAC team <ng-eseries-upstream-maintainers@netapp.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christophe Varoqui <christophe.varoqui@opensvc.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Cc: device-mapper development <dm-devel@redhat.com>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Commit 56f3d383 ("scsi: scsi_devinfo: Add TRY_VPD_PAGES to HITACHI
OPEN-V blacklist entry") modified some Hitachi entries:

    HITACHI is always supporting VPD pages, even though it's claiming to
    support SCSI Revision 3 only.

The same should have been done also for HP-rebranded.

[mkp: checkpatch and tweaked commit message]

Cc: Hannes Reinecke <hare@suse.de>
Cc: Takahiro Yasui <takahiro.yasui@hds.com>
Cc: Matthias Rudolph <Matthias.Rudolph@hitachivantara.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Commit 627511e3 ("[SCSI] scsi_devinfo: update Hitachi entries (v2)")
modified some Hitachi entries:

    Four models, OPEN-/DF400/DF500/DISK-SUBSYSTEM, can handle
    REPORT_LUN, and the BLIST_REPORTLUN2 flag needs to be set. And DF600
    doesn't require any flags because it returns ANSI 03h (SPC).

The same should have been done also for HP counterparts.

[mkp: checkpatch and tweaked commit message]

Cc: Takahiro Yasui <takahiro.yasui@hds.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Matthias Rudolph <Matthias.Rudolph@hds.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Cc: SCSI ML <linux-scsi@vger.kernel.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

find_first_zero_bit()'s parameter 'size' is defined in bits, not in
bytes.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There are several places where the source is not indented correctly with
either too many or too few levels of intentation. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Remove this function since it has an empty body.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Commit 651a0136 ("scsi: scsi_transport_sas: switch to bsg-lib for
SMP passthrough") removed the only call to scsi_initialize_rq() from
outside the SCSI core. Hence unexport scsi_initialize_rq().
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When driver is loaded in Target/Dual mode, it creates QPair to support
MQ and allocates resources for each QPair. This Qpair initialization is
delayed until the FW personality is changed to Dual/Target mode by
issuing chip reset. At the time of chip reset firmware is re-initilized
in correct personality all the QPairs are initialized by sending
MBC_INITIALIZE_MULTIQ (001Fh).

This patch fixes memory leak by adding check to issue
MBC_INITIALIZE_MULTIQ command only while deleting rsp/req queue when the
flag is set for initiator mode, and clean up QPair resources correctly
during the driver unload. This MBX does not need to be issued for
Target/Dual mode because chip reset will reset ISP.

Fixes: d65237c7 ("scsi: qla2xxx: Fix mailbox failure while deleting Queue pairs")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fix system crash due to NULL pointer access.

qlt_plogi_ack_t and fc_port structures were not properly bound before
calling qlt_plogi_ack_unref().

RIP: 0010:qlt_plogi_ack_unref+0xa1/0x150 [qla2xxx]
Call Trace:
qla24xx_create_new_sess+0xb1/0x320 [qla2xxx]
qla2x00_do_work+0x123/0x260 [qla2xxx]
qla2x00_iocb_work_fn+0x30/0x40 [qla2xxx]
process_one_work+0x1f3/0x530
worker_thread+0x4e/0x480
kthread+0x10c/0x140

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This fix the spinlock recursion issue seen while unloading the driver.

14 [ffff9f2e21e03db8] native_queued_spin_lock_slowpath at ffffffffad0d8802
15 [ffff9f2e21e03dc0] do_raw_spin_lock at ffffffffad0d99e4
16 [ffff9f2e21e03dd8] _raw_spin_lock_irqsave at ffffffffad652471
17 [ffff9f2e21e03e00] qla2x00_els_dcmd_iocb_timeout at ffffffffc070cd63
18 [ffff9f2e21e03e40] qla2x00_sp_timeout at ffffffffc06f06d3 [qla2xxx]
19 [ffff9f2e21e03e68] call_timer_fn at ffffffffad0f97d8
20 [ffff9f2e21e03ed8] run_timer_softirq at ffffffffad0faf47
21 [ffff9f2e21e03f68] __softirqentry_text_start at ffffffffad655f32

Fixes: 6eb54715 ("qla2xxx: Added interface to send explicit LOGO.")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch defers processing of GS IOCB calls from interrupt context to
avoid hardware spinlock recursion.

Following stack trace is seen

? mod_timer+0x193/0x330
? ql_dbg+0xa7/0xf0 [qla2xxx]
_raw_spin_lock_irqsave+0x31/0x40
qla2x00_start_sp+0x3b/0x250 [qla2xxx]
qla24xx_async_gnl+0x1d3/0x240 [qla2xxx]
qla24xx_fcport_handle_login+0x285/0x290 [qla2xxx]
? vprintk_func+0x20/0x50

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Clear loop id after delete to prevent session invalidation of stale
session.

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add correct value of scan_state field indicating state of the FC port

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Current code manually allocate an fcport structure that is not properly
initialize. Replace kzalloc with qla2x00_alloc_fcport, so that all
fields are initialized.  Also set set scan flag to port found

Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Original code acquires hardware_lock to add Abort IOCB onto driver
request queue for processing. However, abort_command() will also acquire
hardware lock to look up sp pointer before issuing abort IOCB command
resulting into a deadlock. This patch safely removes the possible
deadlock scenario by removing extra spinlock.

Fixes: 6eb54715 ("qla2xxx: Added interface to send explicit LOGO.")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Get Port Database MBX cmd is to validate current Login state upon PRLI
completion. Current code looks at the last login state for re-validation
which was incorrect. This patch removed incorrect state check.

Fixes: 15f30a57 ("qla2xxx: Use IOCB interface to submit non-critical MBX.")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Current driver design schedules relogin process via DPC thread every 1
second. In a large fabric, this DPC thread tries to schedule too many
jobs and might get overloaded. As a result of this processing of DPC
thread, it can schedule relogin earlier than 1 second.

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If user swaps one target port for another target port for same switch
port, the new target port is not being recognized by the driver. Current
code assumes that old Target port has recovered from link down. The fix
will ask switch what is the WWPN of a specific NportID (GPNID) rather
than assuming it's the same Target port which has came back.

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add check to make sure we are cleaning up global target host list only
for NPIV hosts

Fixes: bdbe24de ("scsi: qla2xxx: Cleanup NPIV host in target mode during config teardown")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This patch returns discovery state machine back to Login Complete.

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

GPNID is triggered by RSCN. For multiple RSCNs of the same affected
NPORT ID, serialize the GPNID to prevent confusion.

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Retry GID_PN & GPN_ID switch commands for time out case.

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When NPort Handle is in use, driver needs to mark the handle as used and
pick another. Instead, the code clears the handle and re-pick the same
handle.

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org> # 4.10+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Fix co-existence between Block MQ and Target Mode. Block MQ and
initiator mode requires midlayer queue mapping to check for IRQ to be
affinitized. For target mode, it's not the case.

Fixes: 09620eeb ("scsi: qla2xxx: Add debug knob for user control workload")
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>