We were basically opencoding the same thing in both
hw_init and resume and hw_fini and suspend.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This is the recommended setting from the hw team for newer
versions of the firmware.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

This removes the last depency of radeon for dev->struct_mutex!

Also the locking scheme for hyperz/cmask owners seems a bit unsound,
there's no protection in the preclose handler (and that never did hold
dev->struct_mutex while being called). So grab the same lock there,
too.

There's also all the checks in the cs checker, but since the overall
design seems to never stall for the previous owner I figured it's ok
if I leave this racy. It was racy even before I touched it after all
too.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The first lockup fence will lock the fence list of scheduler.
Then cancel the delayed workqueues for all clean pending fences
without waiting the workqueues to finish.

Change-Id: I9bec826de1aa49d587b0662f3fb4a95333979429
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Change-Id: I67e987db0efdca28faa80b332b75571192130d33
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: David Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Output all VM mappings a command submission uses.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

This makes it much easier to find when userspace misses to send some buffers.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Port of radeon commit 9b7d786b.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>

This was added to two radeon files even though they don't use any
vga_switcheroo symbols, the amdgpu fork inherited them:

Added to amdgpu_acpi.c by commit d7a2952f ("drm/radeon: Add
support for the ATIF ACPI method to the radeon driver").

Added to amdgpu_bios.c by commit 6a9ee8af ("vga_switcheroo:
initial implementation (v15)").
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This was added to three files even though they don't use any
vga_switcheroo symbols:

Added to radeon_acpi.c by commit d7a2952f ("drm/radeon: Add
support for the ATIF ACPI method to the radeon driver").

Added to radeon_asic.c by commit 0a10c851 ("drm/radeon: create
radeon_asic.c").

Added to radeon_bios.c by commit 6a9ee8af ("vga_switcheroo:
initial implementation (v15)").
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Check to make sure we aren't touching a non-existent
display controller and simplify the code.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Rework the sdma structures in the driver to
consolidate all of the sdma info into a single
structure and allow for asics that may have
different numbers of sdma instances.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Everything is evicted from VRAM before suspend, so we need to make
sure all BOs are unpinned and re-pinned after resume. Fixes broken
mouse cursor after resume introduced by commit b9729b17.

Port of radeon commit:
f3cbb17bReviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Port of radeon commit:
8991668aReviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Take a GEM reference for and pin the new cursor BO, unpin and drop the
GEM reference for the old cursor BO in dce8 crtc_cursor_set2, and use
amdgpu_crtc->cursor_addr in dce8 set_cursor.

This fixes dce8 cursor_reset accidentally incrementing the cursor BO
pin count, and cleans up the code a little.

Port of radeon commit:
cd404af0Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It's only needed in dce8 crtc_cursor_set2.

Port of radeon commit:
2e007e61Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Setting a mode seems to clear the cursor registers, so we need to
re-program them to make sure the cursor is visible.

Port of radeon commit:
6d3759fa

v2: change radeon reference in error message
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The cursor_set2 hook provides the cursor hotspot position within the
cursor image. When the hotspot position changes, we can adjust the cursor
position such that the hotspot doesn't move on the screen. This prevents
the cursor from appearing to intermittently jump around on the screen
when the position of the hotspot within the cursor image changes.

Port of radeon commits:
78b1a601
3feba08dReviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Port of radeon commit:
8991668aReviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Take a GEM reference for and pin the new cursor BO, unpin and drop the
GEM reference for the old cursor BO in dce11 crtc_cursor_set2, and use
amdgpu_crtc->cursor_addr in dce11 set_cursor.

This fixes dce11 cursor_reset accidentally incrementing the cursor BO
pin count, and cleans up the code a little.

Port of radeon commit:
cd404af0Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It's only needed in dce11 crtc_cursor_set2.

Port of radeon commit:
2e007e61Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Setting a mode seems to clear the cursor registers, so we need to
re-program them to make sure the cursor is visible.

Port of radeon commit:
6d3759fa

v2: change radeon reference in error output
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The cursor_set2 hook provides the cursor hotspot position within the
cursor image. When the hotspot position changes, we can adjust the cursor
position such that the hotspot doesn't move on the screen. This prevents
the cursor from appearing to intermittently jump around on the screen
when the position of the hotspot within the cursor image changes.

Port of radeon commits:
78b1a601
3feba08dReviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Port of radeon commit:
8991668aReviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Take a GEM reference for and pin the new cursor BO, unpin and drop the
GEM reference for the old cursor BO in dce10 crtc_cursor_set2, and use
amdgpu_crtc->cursor_addr in dce10 set_cursor.

This fixes dce10 cursor_reset accidentally incrementing the cursor BO
pin count, and cleans up the code a little.

Port of radeon commit:
cd404af0Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It's only needed in dce10 crtc_cursor_set2.

Port of radeon commit:
2e007e61Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Setting a mode seems to clear the cursor registers, so we need to
re-program them to make sure the cursor is visible.

Port of radeon commit:
6d3759fa

v2: change radeon reference in error message
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The cursor_set2 hook provides the cursor hotspot position within the
cursor image. When the hotspot position changes, we can adjust the cursor
position such that the hotspot doesn't move on the screen. This prevents
the cursor from appearing to intermittently jump around on the screen
when the position of the hotspot within the cursor image changes.

Port of radeon commits:
78b1a601
3feba08dReviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Better precision than the regular div opcode.

v2: drop 64 bit divide
v3: fix op handling.  This actually is a 64 bit divide.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Better precision than the regular mul opcode.

v2: handle big endian properly.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Just skips a data section.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Basically a nop.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

These are buggy on some asics and not really used anymore
now that the GPU schedular is enabled.

Change-Id: I67182b409d64de308392a15d1a0a15018071dc0b
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Change-Id: Idce64f63e8422324996fc5d583d0bc9a5ac60d0c
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

need to decrease visible vram usage by default.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: monk.liu <monk.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Calculate the driver state in sw_init and program the
registers in hw init.
Acked-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

There doesn't seem to be any need to have 'ib' volatile, the code is
not even consistent with it and some places already miss it. As it is
now it's just making gcc produce worse code. If there are special
requirements for that memory, then proper primitives like memory
barriers or accessor functions should be used, but it doesn't look
like that is needed here.
While at it, change the type to match the one in radeon_ib structure.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>