Other machines may wish to make use of the VIC support code, so
move it to arch/arm/common.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The default is already 'n' so there's no need to explicitly state it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch adds register switch support in nommu mode.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This patch supports start_thread in nommu mode which requires the
base index register.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

This field is redundent since it must be equal to PHYS_OFFSET anyway.

Now that no code uses it anymore, mark it deprecated and remove all
initializations from the tree.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Nicolas Pitre

This field is redundent since it must be equal to PHYS_OFFSET anyway.

First, let's  use PHYS_OFFSET directly instead.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Matt Reimer

IMX serial parity generation doesn't work because of a simple logic error. This patch fixes it and now Bluetooth works on R1000.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Patch from Lennert Buytenhek

For the ixp2000 netdev driver, we need to map in a chunk of SRAM (to
store the transmit and receive descriptors) and the scratch get/put
area (so that we can use the scratchpad rings in the cpu for managing
the descriptors.)  These are the final two mappings needed for the
netdev driver and the last missing piece for the driver in mainline
to work.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

At least some versions of the via-velocity hardware only support
checksumming IPv4 frames in hardware.  However, the driver is currently
setting the NETIF_F_HW_CSUM flag, which indicates support for more than
just IPv4.  This results in errors when trying to use IPv6 over
via-velocity hardware.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

The comments in ieee80211.h claim that one doesn't need to set the len
parameter of the stats struct. But if one doesn't, the management frames
are read far over the memory they actually occupy causing badness.
Signed-Off-By: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

	I believe I see the race Michael refers to (tlb_choose_channel
may set head, which tlb_init_slave clears), although I was not able to
reproduce it.  I have updated his patch for the current netdev-2.6.git
tree and added a version update.  His original comment follows:

Our systems have been crashing during testing of PCI HotPlug
support in the various networking components.  We've faulted in
the bonding driver due to a bug in bond_alb.c:tlb_clear_slave()

In that routine, the last modification to the TLB hash table is
made without protection of the lock, allowing a race that can lead
tlb_choose_channel() to select an invalid table element.

	-J
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

This patch allows the Atmel driver to work correctly with wpa_supplicant
and other programs that require some conformance with WEXT-18.  It
should not affect current behavior of the driver.  The patch does four
things:

1) Implements SIOCSIWENCODEEXT, SIOCGIWENCODEEXT, SIOCSIWAUTH, and
SIOCGIWAUTH calls for unencrypted and WEP operation

2) Accepts zero-filled addresses for SIOCSIWAP, which are legal and
should turn off any previous forced WAP address

3) Sends association and de-association events to userspace at most of
the appropriate times

4) Fixes erroneous order of CIPHER_SUITE_WEP_* arguments in one location
which are actually unused anyway
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Replace the MODULE_PARM usage in uli526x.c with module_param.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Make the driver produce the string used by phy_connect and have board specific
code pass the integer mii bus id and phy device id for the specific controller
instance.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Add the PHY_ID_FMT macro to ensure that the format of the id string used by a
driver to match to its specific phy is consistent between the mdio_bus and the
driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

We can now have the gianfar mii platform device have a proper resource for the
IO memory region for its registers.  Previously we passed this information
that the platform_data structure because we couldn't handle overlapping memory
regions for platform devices.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

Missing include of <linux/in.h> to get definition of IPPROTO_UDP.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

airo.c currently has MICSUPPORT enabled, which requires CONFIG_CRYPTO.  A
user reported a build failure which is due to the lack of a Kconfig
dependency.  See http://bugs.debian.org/344205.

This patch makes Kconfig enforce this dependency.
Signed-off-by: dann frazier <dannf@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

We have identified two related bugs in the e100 driver.

Both bugs are related to manipulation of the MDI control register.

The first problem is that the Ready bit is being ignored when writing to
the Control register; we noticed this because the Linux bonding driver
would occasionally come to the spurious conclusion that the link was down
when querying Link State.  It turned out that by failing to wait for a
previous command to complete it was selecting what was essentially a random
register in the MDI register set.  When we added code that waits for the
Ready bit (as shown in the patch file below) all such problems ceased.

The second problem is that, although access to the MDI registers involves
multiple steps which must not be intermixed, nothing was defending against
two or more threads attempting simultaneous access.  The most obvious
situation where such interference could occur involves the watchdog versus
ioctl paths, but there are probably others, so we recommend the locking
shown in our patch file.
Signed-off-by: Michael O'Donnell <Michael.ODonnell@stratus.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

There's a problem with the REQ_BLOCK_PC handling as well (bad ->data_len
handling) where it could actually complete a request ahead of time.  I
suggest we just back this out for now, I will resubmit it later when I'm
fully confident in it.

This reverts commit 8672d571Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Turn several drivers/serial/ semaphores-used-as-mutex into mutexes
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

convert mfd and mmc to mutexes
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The arm clock semaphores are strict mutexes, convert them to the new
mutex implementation
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix up delete/modify conflict of arch/ppc/kernel/process.c by hand (it's
gone, gone, gone).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

With the "power/state" sysfs interface being deprecated, make another
one available which is compatible to what was discussed on the linux
PM mailinglist.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>

Add IDs for Sierra Aircard 55 CDMA 1xrtt Modem -- a CIS update is required
for this card.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>

This is part of a patch from Marc Singer to allow r2 to be
passed to the kernel.  Marc's original comments follow:

This revised R2 (atags pointer) patch incorporates comments from Nico
Pitre and Ben Dooks. It modifies the head.S files such that the R2
value set by the bootloader is conveyed to the kernel startup code.
The kernel head.S heuristically validates the pointer. It will set R2
to zero if it believes the pointer is invalid. Presently, it requires
that the ATAGS list reside in the first 16KiB of physical RAM.
Relaxing this contraint may be both desirable as well as tricky.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

we always set ->SCp.ptr to physical address of buffer; for DMA that's
just what we need, but we end up using it as virtual address in PIO
case of esp_do_data(), with obvious breakage as soon as memory mapping
becomes non-trivial.  The fix is obvious.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

To be used by module_init() function should return int; same for functions
that have "return -ENODEV;" in them, actually ;-)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

it's *(.data.init_task), not init_task...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

with gcc4 these have file scope, so having them different in different
blocks doesn't work anymore
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>