- 20 Mar, 2012 31 commits
-
-
Ivan Kalvachev authored
It is mostly copy/paste of the 520e code with setting GPIO7 removed (no LED light). I've worked on just released vanilla linux-3.3.0 kernel, so there may be 1/2 lines offset to the internal working source, but most of the code should apply cleanly. I was able to get the DVB-C working (tuned and watched TV). Haven't tested DVB-T (no signal atm). Special thanks to everybody who worked on the code and to Antti Palosaari and Devin Heitmueller who provided essential support on irc. Hardware is based of: Empia EM2884 Micronas DRX 3926K NXP TDA18271HDC2 AVF4910 (not used atm) Signed-off-by: Ivan Kalvachev <ikalvachev@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Antti Palosaari authored
Hardware is based of: Empia EM2884 Micronas DRX 3926K NXP TDA18271HDC2 ... + analog parts. Analog is not supported currently. Only DVB-T and DVB-C. There seems to be still problems for locking DVB-C channels which have strong signal. Attenuator helps. I think it is demodulator IF/RF AGC issue. Lets fix it later. Patches are welcome. Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Hans Verkuil authored
I found one more place where -EINVAL is used instead of -ENOTTY: Note that drivers/media/dvb/dvb-core/dvbdev.c has the same code, but as far as I can tell DVB is still using -EINVAL for unknown ioctls so I didn't change that. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
- copyright change - use the kbuild module name for messages - remove useless code - add/remove blank lines, parenthesis, braces - add/change some information messages Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
The bridge register 1061 may take only the values 01 (stop) or 03 (start). Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
The JPEG compression may be adjusted from the packet fill ratio and from the flag 'USB FIFO full' returned in each frame. The code is adapted from the one in gspca sonixj and uses a workqueue. Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
The new functions i2c_w1_buf() and i2c_w2_buf() handle the write loops. Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
The JPEG compression quality was hardcoded to 95%. This value was too big, raising often buffer overflows. This quality is now 80% by default and is settable. Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
The reset of the Omnivision sensors takes a long time (200ms). Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
The frame header was checked on packets of size 64 bytes only, while the webcams may put a frame header at the beginning of bigger packets. Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
The line defining the value of the register 08 for the sensor cs2102k was commented by error in commit 30c73d46. Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jose Alberto Reguero authored
This patch adds brightness control to the OmniVision 5621 sensor. Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-François Moine authored
This patch is adapted from Sylwester's patch proposed on 2012/02/22. The JPEG compression control does not work with the autoquality done for the sensors hv7131r and pas202b. Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Michael Krufky authored
The D1F5 revision of the WinTV HVR-1900 uses a tda18271c2 tuner instead of a tda18271c1 tuner as used in revision D1E9. To account for this, we must hardcode the frontend configuration to use the same IF frequency configuration for both revisions of the device. 6MHz DVB-T is unaffected by this issue, as the recommended IF Frequency configuration for 6MHz DVB-T is the same on both c1 and c2 revisions of the tda18271 tuner. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Cc: Mike Isely <isely@pobox.com> Cc: stable@kernel.org Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Michael Krufky authored
Remove unnecessary register access in mxl111sf_ep6_streaming_ctrl() This code breaks driver operation in kernel 3.3 and later, although it works properly in 3.2 Disable register access to 0x12 for now. Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Cc: stable@kernel.org Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Antti Palosaari authored
Hardware is based of: Empia EM2874B Micronas DRX 3913KA2 NXP TDA18271HDC2 Only DVB-C supported currently since missing firmware. According to my tests, DRX 3913KA2 demodulator requires firmware in order to support DVB-T mode. Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jonathan Corbet authored
We've spammed enough logfiles at this point. Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jonathan Corbet authored
We still need to power up the controller to avoid unsightly self-immolation should something try to access its registers, but the sensor can stay powered down unless the camera was actually operating at suspend time. This gets rid of the camera LED flash on resume, fixing OLPC bug #11644. Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jonathan Corbet authored
There is only one frame known to the DMA engine in scatter/gather mode, but it still tells us that any or all of frames 1-3 are done at each completion interrupt. Avoid the creation of junk frames by being sure to only "complete" one on each interrupt. Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jonathan Corbet authored
I had learned through hard experience that dinking around with the DMA descriptors while the C1_DESC_ENA enable bit was set is a recipe for all kinds of truly malicious behavior on the hardware's part, regardless of whether the DMA engine is actually operating at the time. That notwithstanding, the driver did so dink, resulting in "green frame" captures and the death of the system in random, spectacular ways. Move the tweaking of C1_DESC_ENA to the same function that sets the descriptor so we know that we'll never try to set a descriptor while that bit is set. Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jonathan Corbet authored
Experience shows that, on the Armada platform, it can take as much as 120ms for the DMA engine to actually shut down after it has been told to. So a 40ms timeout is not adequate; use 150ms instead. Also make sure we don't leave the DMA_ACTIVE flag set once things are down. Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jonathan Corbet authored
The marvell cam driver retained just enough of the owner-tracking logic from cafe_ccic to be broken; it could, conceivably, cause the driver to release DMA memory while the controller is still active. Simply remove the remaining pieces and ensure that the controller is stopped before we free things. Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jonathan Corbet authored
The controller stop/restart logic could possibly restart DMA after the driver things things have stopped, with suitably ugly results. Make sure that we only restart the hardware if we're supposed to be streaming. Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Ezequiel García authored
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Philipp Zabel authored
This patch adds clk_prepare/clk_unprepare calls to the pxa_camera driver by using the helper functions clk_prepare_enable and clk_disable_unprepare. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
Newer CEU versions, e.g., the one, used on sh7372, support image sizes larger than 2560x1920. Retrieve maximum sizes from platform properties. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Guennadi Liakhovetski authored
soc_camera_power_on() calls client's .s_power(1) method, which can try to access the client hardware. This, however, is typically only possible, after calling host's .add() method, because that's where the host driver usually turns the master clock on. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Ezequiel García authored
This changes rc_core to not load the IR decoders at load time, postponing it to load only if a RC_DRIVER_IR_RAW device is registered via rc_register_device. We use a static boolean variable, to ensure decoders modules are only loaded once. Tested with rc-loopback device only. Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com> Acked-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
- 19 Mar, 2012 9 commits
-
-
Malcolm Priestley authored
Remove incorrect SEC_MINI_B settings-TODO complete this section. Correct break and remove return -EINVAL within set tone. It appears there is a bug that occasionally something other than ON/OFF is sent stalling the driver. Just continue and write back registers. Set register b2 in setup. This is the set voltage pin which isn't used in lmedm04 driver but it is always set to 0x1. Correct the if statements in set_tuner_rf. Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Antti Palosaari authored
Some changes for previous patch I liked to do. Just move tuner init and sleep to own functions from the demod init and sleep functions. Functionality remains still almost the same. Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Gordon Hecker authored
The i2c failures were caused by enabling both i2c gates at the same time while putting the tuners asleep. This patch removes the init() and sleep() callbacks from the tuner, to prevent frontend.c from calling i2c_gate_ctrl tuner init / sleep i2c_gate_ctrl without holding the lock. tuner init() and sleep() are instead called in frontend init() and sleep(). Signed-off-by: Gordon Hecker <ghecker@gmx.de> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean Delvare authored
Reported by kmemleak. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean Delvare authored
struct dvb_usb_device *d can never be NULL so don't waste time checking for this. Rationale: the urb's context is set when usb_fill_bulk_urb() is called in dib0700_rc_setup(), and never changes after that. d is dereferenced unconditionally in dib0700_rc_setup() so it can't be NULL or the driver would crash right away. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Ezequiel García authored
This patch saves 255 bytes of stack on usb_probe() by removing a char array. In some platforms this is represents a substantial save. Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Michael Krufky authored
The au8522 driver programs the tuner after programming the demodulator, but the tuner should be programmed first. This patch fixes this behavior. EDIT: Apparantly Devin created a similar patch some time ago, but hasn't submitted it for merge. I never saw his patch, but I thank him anyhow for his efforts. In addition, Devin pointed out a flaw in my patch: This newly generated patch takes Devin's comments into account. Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Cc: stable@kernel.org Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jarod Wilson authored
Yet another device ID that has started showing up in the wild. Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Laurent Pinchart authored
Media-related drivers living outside drivers/media/ (such as the UVC gadget driver in drivers/usb/gadget/) rely on the media core being initialized before they're probed. As drivers/usb/ is linked before drivers/media/, this is currently not the case and will lead to crashes if the drivers are not compiled as modules. Register media_devnode_init() as a subsys_initcall() instead of module_init() to fix this. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by: Bhupesh Sharma <bhupesh.sharma@st.com> Acked-by: Sakari Ailus <sakari.ailus@iki.fi> Tested-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-