The CX23885 IR controller was reported to cause an interrupt storm
on a TeVii S470 card, but was reported fine on an HVR-1250.  Keep
integrated IR disabled by default on CX2388[57] based cards to avoid
a bad user experience in the general case.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Interrupts from the AV Core are best handled by a workqueue handler
since many I2C transactions are required to service the AV Core
interrupt.  The AV_CORE PCI interrupt is disabled by the IRQ handler
and reenabled when the work handler is finished.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This patch encapsulates access to the PCI_INT_MSK register and
dev->pci_irqmask variable and protects them with a spinlock.
This is needed because both the hard IRQ handler and a workhandler
will need to manipulate the mask to disable the AV_CORE interrupt.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Add initial IR Rx support using the intergrated IR controller in the
A/V core of the CX23885 bridge chip.

This initial support is flawed in that I2C transactions should not
be performed in a hard irq context.  That will be fixed in a
follow on patch.

The TeVii S470 support is reported to generate perptual interrupts
that renders a user' system nearly unusable.  The TeVii S470 IR
will be disabled by default in a follow on patch.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This patch is primarily a port of the integrated IR controller code in
cx23885/cx23888-ir.c.  Right now, only the CX2388[57] AV core will
really try to set up IR. This IR support, by design, still requires the
bridge driver to do final IO pin mux configuration and setup of the IR
controller parameters.

For the CX2388[578] chips, enabling the AV Core for IR also starts
sending Audio and Video interrupts to the bridge driver.  For
CX2388[578] chips audio and video interrupts are ignored and
acknowledged when they happen.

IR interrupt handling and status logging is exluded for the CX23888
which does not have an IR controller on the AV core.

Note that experimentation reveals that the IR irq enables on the
CX23885 have an inverted logic sense.  The CX23887 likely suffers from
the same quirk.  For these chips, those irq enable bits are handled
as interrupt disables.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The CX2584x and related cores are multifunction subdevices with a number
of internal blocks that act as interrupt sources.  Move the v4L2_subdev
interrupt_service_routine callback from v4l_subdev_ir_ops to
v4l2_subdev_core_ops, as the video and audio blocks of a CX2584x and
related cores can generate interrupts along with the IR block.  This
change also makes sense for other subdev's that generate interrupts and
do not have an IR block.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Explicitly configure the IR Tx and IR Rx pins to be driven by the
IR Rx and Tx pads from the AV core for CX23888 IR.

For the HVR-1850 and HVR-1290 configure the IR Tx level inversion,
so the Tx LED is off when idle.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

There is a distinction on IR Tx for the CX2388[578] chips of carrier
sense inversion (space is a carrier burst and mark is no burst) and I/O
pin level inversion (0 is high output level, 1 is low output level).
Allow the caller to set these parameters distinctly as v4l2_subdevice
IR parameters.  This permits the IR device to be configured and enabled
without the IR Tx LED being on during idle/space time due to an external
hardware level inversion
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Add s_io_pin_config core subdev op for the CX2388[578] AV cores.
This is complete for IR_RX, IR_TX, GPIOs 16,19-23, and IRQ_N.
It likely needs work for the I2S signal direction.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Add a method to v4l2_sudev_core_ops to allow bridge drivers to
manage what signal pads/functions are routed out to multiplexed IO pins on a
pin by pin basis.  The interface also allows specifying initial output settings
for pins and disabling an IO pin altogether.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Add a simple log_status function for raw analog video capture device nodes,
to provide insight into the state of the CX2388[578] A/V decoder core.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The offset in the eeprom data for the 79501 version of the HVR-1250 is at 0xc0
vs. the standard 0x80.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

There was a small window between writing the cx25840 register
address over the i2c bus and reading the register contents back from the
cx25840 device that the i2c adapter lock was released.  This change ensures the
adapter lock is not released until the register read is done.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Function i2c_wait_done() never returns negative values, so there is no
point in checking for them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Don't just check for nacks on zero-length transactions. Check on
other transactions too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Documentation/i2c/fault-codes says that i2c adapter drivers should
return -ENXIO when no slave acks an address byte.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

On laptops, the webcam sometimes disconnects when writing the first main
register (b300). This patch prevents the creation of a new /dev/video<n>
on streaming start.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The added controls are exposure, gain, autogain and backlight compensation.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The JPEG format did not work fine. The Bayer format offers correct VGA (640x480)
resolution, but bad QQVGA (160x120). This last resolution is removed.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The bit 7 of the sensor gain register multiplies the 7bits value by two.
It is now always set with half the user gain value.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The start_1 exchange must be done by (reg, val) * 5 and not 8.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The sensor enum definition was not at the right place.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  arch/tile: check kmalloc() result
  arch/tile: catch up on various minor cleanups.
  arch/tile: avoid erroneous error return for PTRACE_POKEUSR.
  tile: set ARCH_KMALLOC_MINALIGN
  tile: remove homegrown L1_CACHE_ALIGN macro
  arch/tile: Miscellaneous cleanup changes.
  arch/tile: Split the icache flush code off to a generic <arch> header.
  arch/tile: Fix bug in support for atomic64_xx() ops.
  arch/tile: Shrink the tile-opcode files considerably.
  arch/tile: Add driver to enable access to the user dynamic network.
  arch/tile: Enable more sophisticated IRQ model for 32-bit chips.
  Move list types from <linux/list.h> to <linux/types.h>.
  Add wait4() back to the set of <asm-generic/unistd.h> syscalls.
  Revert adding some arch-specific signal syscalls to <linux/syscalls.h>.
  arch/tile: Do not use GFP_KERNEL for dma_alloc_coherent(). Feedback from fujita.tomonori@lab.ntt.co.jp.
  arch/tile: core support for Tilera 32-bit chips.
  Fix up the "generic" unistd.h ABI to be more useful.

* 'for-linus' of git://www.jni.nu/cris: (51 commits)
  CRIS: Fix alignment problem for older ld
  CRIS: Always dump registers for segfaulting process.
  CRIS: Add config for pausing a seg-faulting process
  CRIS: Don't take faults while in_atomic
  CRIS: Fixup lookup for delay slot faults
  CRIS: Discard exit.text and .data at runtime
  CRIS: Add cache aligned and read mostly data sections
  CRIS: Return something from profile write
  CRIS: Add ARTPEC-3 and timestamps for sync-serial
  CRIS: Better ARTPEC-3 support for gpio
  CRIS: Add include guard
  CRIS: Better handling of pinmux settings
  CRIS: New DMA defines for ARTPEC-3
  CRIS: __do_strncpy_from_user: Don't read the byte beyond the nil
  CRIS: Pagetable for ARTPEC-3
  CRIS: Machine dependent memmap.h
  CRIS: Check if pointer is set before using it
  CRIS: Machine dependent dma.h
  CRIS: Define __read_mostly for CRISv32
  CRIS: Discard .note.gnu.build-id section
  ...

* 'for-linus' of git://android.kernel.org/kernel/tegra:
  [ARM] tegra: add MAINTAINERS entry
  [ARM] tegra: harmony: Add harmony board file
  [ARM] tegra: add pinmux support
  [ARM] tegra: add GPIO support
  [ARM] tegra: Add timer support
  [ARM] tegra: SMP support
  [ARM] tegra: Add clock support
  [ARM] tegra: Add IRQ support
  [ARM] tegra: initial tegra support

* 'for-linus' of git://github.com/schandinat/linux-2.6:
  drivers/video/via/via-gpio.c: fix warning
  viafb: Depends on X86
  fbdev: section cleanup in viafb driver
  viafb: fix accel_flags check_var bug
  viafb: probe cleanups
  viafb: remove ioctls which break the framebuffer interface
  viafb: update fix before calculating depth
  viafb: PLL value cleanup
  viafb: simplify lcd size "detection"
  viafb: fix PCI table
  viafb: add lcd scaling support for some IGPs
  viafb: improve lcd code readability
  viafb: remove duplicated scaling code
  MAINTAINERS: update viafb entry

* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux: (64 commits)
  OMAP: DSS2: OMAPFB: add support for FBIO_WAITFORVSYNC
  OMAP: DSS2: Replace strncmp() with sysfs_streq() in overlay_manager_store()
  OMAP: DSS2: Fix error path in omap_dsi_update()
  OMAP: DSS2: TDO35S: fix video signaling
  OMAP: DSS2: OMAPFB: Fix invalid bpp for PAL and NTSC modes
  OMAP: DSS2: OMAPFB: Fix probe error path
  OMAP3EVM: Replace vdvi regulator supply with vdds_dsi
  OMAP: DSS2: Remove extra return statement
  OMAP: DSS2: adjust YUV overlay width to be even
  OMAP: DSS2: OMAPFB: Fix sysfs mirror input check
  OMAP: DSS2: OMAPFB: Remove redundant color register range check
  OMAP: DSS2: OMAPFB: Remove redundant rotate range check
  OMAP: DSS2: OMAPFB: Check fb2display() return value
  OMAP: DSS2: Taal: Optimize enable_te, rotate, mirror when value unchanged
  OMAP: DSS2: DSI: detect unsupported update requests
  OMAP: DSS2: DSI: increase FIFO low threshold
  OMAP: DSS2: DSI: Add error IRQ mask for DSI complexIO
  OMAP: DSS2: DSI: Remove BTA after set_max_rx_packet_size
  OMAP: DSS2: change manual update scaling setup
  OMAP: DSS2: DSI: use BTA to end the frame transfer
  ...

Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (143 commits)
  omap: mailbox: reorganize headers
  omap: mailbox: standarize on 'omap-mailbox'
  omap: mailbox: only compile for configured archs
  omap: mailbox: simplify omap_mbox_register()
  omap: mailbox: reorganize registering
  omap: mailbox: add IRQ names
  omap: mailbox: remove unecessary fields
  omap: mailbox: don't export unecessary symbols
  omap: mailbox: update omap1 probing
  omap: mailbox: use correct config for omap1
  omap: mailbox: 2420 should be detected at run-time
  omap: mailbox: reorganize structures
  omap: mailbox: trivial cleanups
  omap mailbox: Set a device in logical mbox instance for traceability
  omap: mailbox: convert block api to kfifo
  omap: mailbox: remove (un)likely macros from cold paths
  omap: mailbox cleanup: split MODULE_AUTHOR line
  omap: mailbox: convert rwlocks to spinlock
  Mailbox: disable mailbox interrupt when request queue
  Mailbox: new mutext lock for h/w mailbox configuration
  ...

Merge branch 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci

* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci:
  davinci: dm646x EVM: Specify reserved EDMA channel/slots
  davinci: da8xx/omapl EVM: Specify reserved channels/slots
  davinci: support for EDMA resource sharing
  davinci: edma: provide ability to detect insufficient CC info data
  davinci: da8xx: sparse cleanup: remove duplicate entries in irq priorities
  davinci: DM365: fixed second serial port
  Davinci: tnetv107x evm board initial support
  Davinci: tnetv107x initial gpio support
  Davinci: tnetv107x soc support
  Davinci: tnetv107x decompresser uart definitions
  Davinci: generalized debug macros

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (82 commits)
  firewire: core: add forgotten dummy driver methods, remove unused ones
  firewire: add isochronous multichannel reception
  firewire: core: small clarifications in core-cdev
  firewire: core: remove unused code
  firewire: ohci: release channel in error path
  firewire: ohci: use memory barriers to order descriptor updates
  tools/firewire: nosy-dump: increment program version
  tools/firewire: nosy-dump: remove unused code
  tools/firewire: nosy-dump: use linux/firewire-constants.h
  tools/firewire: nosy-dump: break up a deeply nested function
  tools/firewire: nosy-dump: make some symbols static or const
  tools/firewire: nosy-dump: change to kernel coding style
  tools/firewire: nosy-dump: work around segfault in decode_fcp
  tools/firewire: nosy-dump: fix it on x86-64
  tools/firewire: add userspace front-end of nosy
  firewire: nosy: note ioctls in ioctl-number.txt
  firewire: nosy: use generic printk macros
  firewire: nosy: endianess fixes and annotations
  firewire: nosy: annotate __user pointers and __iomem pointers
  firewire: nosy: fix device shutdown with active client
  ...

* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (27 commits)
  ACPI / ACPICA: Simplify acpi_ev_initialize_gpe_block()
  ACPI / ACPICA: Fail acpi_gpe_wakeup() if ACPI_GPE_CAN_WAKE is unset
  ACPI / ACPICA: Do not execute _PRW methods during initialization
  ACPI: Fix bogus GPE test in acpi_bus_set_run_wake_flags()
  ACPICA: Update version to 20100702
  ACPICA: Fix for Alias references within Package objects
  ACPICA: Fix lint warning for 64-bit constant
  ACPICA: Remove obsolete GPE function
  ACPICA: Update debug output components
  ACPICA: Add support for WDDT - Watchdog Descriptor Table
  ACPICA: Drop acpi_set_gpe
  ACPICA: Use low-level GPE enable during GPE block initialization
  ACPI / EC: Do not use acpi_set_gpe
  ACPI / EC: Drop suspend and resume routines
  ACPICA: Remove wakeup GPE reference counting which is not used
  ACPICA: Introduce acpi_gpe_wakeup()
  ACPICA: Rename acpi_hw_gpe_register_bit
  ACPICA: Update version to 20100528
  ACPICA: Add signatures for undefined tables: ATKG, GSCI, IEIT
  ACPICA: Optimization: Reduce the number of namespace walks
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (42 commits)
  IB/qib: Add missing <linux/slab.h> include
  IB/ehca: Drop unnecessary NULL test
  RDMA/nes: Fix confusing if statement indentation
  IB/ehca: Init irq tasklet before irq can happen
  RDMA/nes: Fix misindented code
  RDMA/nes: Fix showing wqm_quanta
  RDMA/nes: Get rid of "set but not used" variables
  RDMA/nes: Read firmware version from correct place
  IB/srp: Export req_lim via sysfs
  IB/srp: Make receive buffer handling more robust
  IB/srp: Use print_hex_dump()
  IB: Rename RAW_ETY to RAW_ETHERTYPE
  RDMA/nes: Fix two sparse warnings
  RDMA/cxgb3: Make needlessly global iwch_l2t_send() static
  IB/iser: Make needlessly global iser_alloc_rx_descriptors() static
  RDMA/cxgb4: Add timeouts when waiting for FW responses
  IB/qib: Fix race between qib_error_qp() and receive packet processing
  IB/qib: Limit the number of packets processed per interrupt
  IB/qib: Allow writes to the diag_counters to be able to clear them
  IB/qib: Set cfgctxts to number of CPUs by default
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
  ALSA: hda - Add pin-fix for HP dc5750
  ALSA: als4000: Fix potentially invalid DMA mode setup
  ALSA: als4000: enable burst mode
  ALSA: hda - Fix initial capsrc selection in patch_alc269()
  ASoC: TWL4030: Capture route runtime DAPM ordering fix
  ALSA: hda - Add PC-beep whitelist for an Intel board
  ALSA: hda - More relax for pending period handling
  ALSA: hda - Define AC_FMT_* constants
  ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
  ALSA: hda - Add support for HDMI HBR passthrough
  ALSA: hda - Set Stream Type in Stream Format according to AES0
  ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
  ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
  ASoC: wm9081: fix resource reclaim in wm9081_register error path
  ASoC: wm8978: fix a memory leak if a wm8978_register fail
  ASoC: wm8974: fix a memory leak if another WM8974 is registered
  ASoC: wm8961: fix resource reclaim in wm8961_register error path
  ASoC: wm8955: fix resource reclaim in wm8955_register error path
  ASoC: wm8940: fix a memory leak if wm8940_register return error
  ASoC: wm8904: fix resource reclaim in wm8904_register error path
  ...

* 'bkl/core' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing:
  do_coredump: Do not take BKL
  init: Remove the BKL from startup code