Split the connectivity check and recovery routine into separated
functions based on the types
   1. iwl_good_ack_health() - check for ack count
   2. iwl_good_plcp_health() - check for plcp error

Based on the type of errors being detected, different recovery methods
will be used to bring the system back to normal operational state.

Because different NIC has different HW and uCode, the behavior is also
different; these functions thus now form part of the ops infrastructure,
so we can have more control on how to monitor and recover from error condition
case per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Monitors the tx statistics to detect the drop in throughput.
When the throughput drops, the ratio of the actual_ack_count and the
expected_ack_count also drops.  At the same time, the aggregated
ba_timeout (the number of ba timeout retries) also rises.  If the
actual_ack_count/expected_ack_count ratio is 0 and the number of ba
timeout retries rises to BA_TIMEOUT_MAX, no tx packets can be delivered.
Reloading the uCode and bring the system back to normal operational
state.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Move the plcp error checking into stand alone function and pointed by ops
to accommodate devices not needing this recovery.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Monitors the internal TX queues periodically.  When a queue is stuck
for some unknown conditions causing the throughput to drop and the
transfer is stop, the driver will force firmware reload and bring the
system back to normal operational state.

The iwlwifi devices behave differently in this regard so this feature is
made part of the ops infrastructure so we can have more control on how to
monitor and recover from tx queue stall case per device.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Align the driver names with official product names for 1000/5000/6000
series. This change mainly affects the debug messages show up in system
log. No functional changes.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

The only caller of this is iwl_rs_rate_init
which is only called with a valid sta_id.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

mac80211 recently implemented two new callbacks that are used to request
station add/remove from the driver. The benefot from these new callbacks
are that they enable the driver to sleep while performing this work.

This is a big patch since a few things need to be coordinated in this move.
First we need to decouple station management from rate scaling, which
caused a lot of code to be moved and/or deleted. Next we needed to tie in
with mac80211's station management callback and let it direct our station
management as well as trigger the rate scaling initialization.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Currently the broadcast station is added after every RXON command. Change
this to only add the broadcast station when interface is added by mac80211.
With this we need some extra work to ensure broadcast station is always
present since station table is cleared when RXON without ASSOC bit set is
sent. To deal with this we re-add all driver known stations to uCode after
such an RXON command is sent.

We also do some cleanup and remove the various calls to clear the station
table. We now only clear the station table in two scenarios:
- only clear uCode portion of station table when RXON command without ASSOC
bit is sent
- clear uCode and driver portion when interface goes down or is removed.

We need to do this clearing when interface goes down to deal with the
device restart/reconfigure routines which do not remove the interface, but
do add the interface during reconfiguration.

Previously the keys were also cleared when station table in driver is
cleared, this is not done anymore since mac80211 will take care that keys
are set and cleared correctly.

There is a known issue with this change. Associating with different AP
without bringing interface down fails with a firmware error. This is
because of the lack of full station notification support and the later
patches in this series that complete the station notification support will
fix this.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

FH register dump debug feature was recently added for 5000 and later;
4965 can use it also.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

when an IBSS merge happened, the supported rates for the newly added station
were left empty, causing the rate control module to be initialized with only
the basic rates.

the section of the ibss code which deals with updating supported rates for
an already existing station failed to inform the rate control module about the
new rates. as both minstrel and pid don't have an update function i just use
the init function.

also remove unnecessary (unsigned long long) casts and edit debug message.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

I accidentally merged an incomplete version of the patch...

This reverts commit b4d59a93.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

After testing, we found that TX_STA_FIFO_MCS is the last MCS value
tried. If the transmission failed, 8 frames have been transmitted. If the
transmission succeed, we can easily compute the number of retry.  This patch fix
the way status is reported to mac80211 rate control. It has 2 bugs :

1. mcs can contain the short preamble flag and it will lead to wrong
computations.

2. minstrel nearly always say that 54 Mbits is the best rate, even if we are
very far from the AP
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is an implementation that support WCID being the encryption key.
Wireless Cli Id was set to be the encryption key in rt2800pci_write_tx_desc
and read (TX_STA_FIFO_WCID) as the current queue entry index.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Acked-by: Ivo van Doorn <ivdoorn@gmail.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix compile warning "rt2800pci.c:1248: warning: 'rt2800pci_device_table'
defined but not used" when building rt2800pci with only soc support
(without pci).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

"ieee80211" was the old name of the common library for ipw2100 and
ipw2200.  It was renamed to "libipw", but some occurrences of the old
name remained.

Rename alloc_ieee80211() to alloc_libipw() and free_ieee80211() to
free_libipw().  Adjust comments and label names.  Change prefixes in
diagnostic messages.

Keep /proc/net/ieee80211 under the original name to avoid breaking user
interface.

Move the affected EXPORT_SYMBOL macros to their proper places.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The hostap driver provides better support for Prism chipset.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

4sec wait is way too pessimistic, TI driver uses 40ms here,
and testing shows that is ebough, so let's also use that.
While at it, add useful sounding comment from the TI driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For some unknown reason ELP_CTRL can't be accesed using
sdio_memcpy_* functions (any attemts to do so result in timeouts):

 wl1251: ERROR sdio write failed (-110)
 wl1251: ERROR sdio read failed (-110)
 wl1251: WARNING WLAN not ready

To fix this, add special IO functions for ELP_CTRL access that are
using sdio_readb/sdio_writeb. Similar handling is done in TI
reference driver from Android code drop.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Make local functions and data static, also constify
some structures. While at it, clean up unneeded includes.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When a cooked monitor interface is active, ieee80211_tx_status()
generates a radiotap header for every single frame, even if it wasn't
injected and thus won't be sent to a monitor interface.
This patch reduces cpu utilization by moving the cooked monitor check a
bit earlier, before it generates the rtap header.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

This code was commented-out when it was added about a year ago and
remains unchanged -- seems as if we don't need it...
Signed-off-by: John W. Linville <linville@tuxdriver.com>

"ath5k: remove stale function declarations, make some functions static"
commented-out some unused functions.  This removes them.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Bob Copeland <me@bobcopeland.com>

For the firmware version 5.30.17 the log file shows:
Firmware version 5.30.11

The variable softSubVer is binary.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For some status, reason is encoded in the low byte, but airo_print_status forgot tp mask low byte in status parsing.

This make it only work when reason is 0.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The latest changes in the N PHY core require the symbol
ssb_chipco_gpio_control to be exported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The rate control algorithm, default is Minstrel for ath5k, determines
the number of retries to use for each rate.  However, there exists in
ath5k_hw_setup_4word_tx_desc (which is called for AR5212 like devices)
a set number of retries defined by AR5K_TUNE_HWTXTRIES.  The set
number of tries is added to the tx_tries0 variable setup by the rate
control algorithm.  This changes the number of retries the rate
control algorithm considers necessary.  By removing the
AR5K_TUNE_HWTXTRIES from the retry calculation the rate control
algorithm is given control over the number of retries.
Signed-off-by: Andrew Blaich <ablaich@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Currently the rate control tx status update gets called for every
subframe of an A-MPDU, and ath9k marks the frame with the relevant
status update with an internal flag. This not suitable for rate control
algorithms using the standard mac80211 rate control API, so fix this by
using IEEE80211_TX_STAT_AMPDU for marking the correct frames that
should be processed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

As wl1271_sdio implementation depends on ARM GPIO impelementation it is
not directly usable on other architectures at the moment. Added
ARM dependency to kernel configuration option.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Here are some minor updates for EEPROM, mostly documentation and some small
fixes which have no effect at the moment.

- fixed_bias is not available for B mode.

- AR5K_EEPROM_[RT]X_CHAIN_DIS is 3 bit. this is MIMO and will not be used in
  ath5k, but just to be correct.

- AR5K_EEPROM_JAP_MID_EN added, and shift of following flags adapted.

- added some documentation for EEPROM values and some comments.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

according to the HAL sources the calculation of the Q value is slightly
different for AR5211 chips.

i couldn't test this since IQ calibration never finishes on older parts. this
is a different problem...
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

add a debugfs file to see different RX and TX errors as reported in our status
descriptors. this can help to diagnose driver problems.

statistics can be cleared by writing 'clear' into the frameerrors file.

example:

# cat /sys/kernel/debug/ath5k/phy0/frameerrors
RX
---------------------
CRC     27      (11%)
PHY     3       (1%)
FIFO    0       (0%)
decrypt 0       (0%)
MIC     0       (0%)
process 0       (0%)
jumbo   0       (0%)
[RX all 245]

TX
---------------------
retry   2       (9%)
FIFO    0       (0%)
filter  0       (0%)
[TX all 21]
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

it's never used and we have a newer implementation in gpio.c.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

it's not used, and we have ah_mac_srev.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

it's never used. probably a leftover from the old OpenHAL days...
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

opmode (operating mode) was defined in struct ath5k_hw and struct ath5k_softc.
remove it from ath5k_hw and use only from ath5k_softc (sc->opmode).

(btw: what's the meaning of opmode when we have multiple interfaces?)
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

save antenna settings and preserve across resets.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

keep statistics about which antenna was used for TX and RX. this is used only
for debugging right now, but might have other applications later.

add a new file 'antenna' in debugfs (/sys/kernel/debug/ath5k/phy0/antenna) to show
antenna use statistics and antenna diversity related register values. it can
also be used to set the antenna mode until we have proper support for that in
iw:
  - echo diversity > antenna: use default antenna mode (RX and TX diversity)
  - echo fixed-a > antenna: use fixed antenna A for RX and TX
  - echo fixed-b > antenna: use fixed antenna B for RX and TX
  - echo clear > antenna: reset antenna statistics
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add support for cfg80211 set_pmksa/del_pmksa/flush_pmksa. Updating PMKID
entry list is done on driver side since NDIS API requires full list update.

v2:
 - fixed to use new netdev_dbg/warn/etc instead of old devdbg/warn/etc
 - fixed false padding from struct ndis_80211_bssid_info
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>