Add an atomic notifier which ensures proper locking when conveying
MCE info to EDAC for decoding. The actual notifier call overrides a
default, negative priority notifier.

Note: make sure we register the default decoder only once since
mcheck_init() runs on each CPU.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20091003065752.GA8935@liondog.tnic>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

This reverts commit db8be50c, as per

	http://bugzilla.kernel.org/show_bug.cgi?id=14374
	http://marc.info/?l=linux-kernel&m=125446885705223&w=4

We simply can't do the USB handoff at FIXUP_HEADER time, since it will
often require us to have valid IO mappings etc.  But that in turn
requires a whole different approach, not this trivial one-liner.

Maybe we could teach all the USB quirk handoff handlers to only do the
quirk if the device has all its registers set up (since if it isn't
initialized, it's unlikely to be active), but regardless that will need
a whole lot more code than just saying "let's do it really early".

The proper fix is almost certainly to just leave the legacy IOMMU
mappings active until after all devices have been initialized.
Reported-by: Nick Piggin <npiggin@suse.de>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As reported in

	http://bugzilla.kernel.org/show_bug.cgi?id=13940

on some system when acpi are enabled, acpi clears some BAR for some
devices without reason, and kernel will need to allocate devices for
them.  It then apparently hits some undocumented resource conflict,
resulting in non-working devices.

Try to increase alignment to get more safe range for unassigned devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (21 commits)
  [S390] dasd: fix race condition in resume code
  [S390] Add EX_TABLE for addressing exception in usercopy functions.
  [S390] 64-bit register support for 31-bit processes
  [S390] hibernate: Use correct place for CPU address in lowcore
  [S390] pm: ignore time spend in suspended state
  [S390] zcrypt: Improve some comments
  [S390] zcrypt: Fix sparse warning.
  [S390] perf_counter: fix vdso detection
  [S390] ftrace: drop nmi protection
  [S390] compat: fix truncate system call wrapper
  [S390] Provide arch specific mdelay implementation.
  [S390] Fix enabled udelay for short delays.
  [S390] cio: allow setting boxed devices offline
  [S390] cio: make not operational handling consistent
  [S390] cio: make disconnected handling consistent
  [S390] Fix memory leak in /proc/cio_ignore
  [S390] cio: channel path memory leak
  [S390] module: fix memory leak in s390 module loader
  [S390] Enable kmemleak on s390.
  [S390] 3270 console build fix
  ...

An interestingly corrupted romfs file system exposed a problem with the
romfs_dev_strnlen function: it's passing the wrong value to its helpers.
Rather than limit the string to the length passed in by the callers, it
uses the size of the device as the limit.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (32 commits)
  USB: serial: no unnecessary GFP_ATOMIC in oti6858
  USB: serial: fix race between unthrottle and completion handler in visor
  USB: serial: fix assumption that throttle/unthrottle cannot sleep
  USB: serial: fix race between unthrottle and completion handler in symbolserial
  USB: serial: fix race between unthrottle and completion handler in opticon
  USB: ehci: Fix isoc scheduling boundary checking.
  USB: storage: When a device returns no sense data, call it a Hardware Error
  USB: small fix in error case of suspend in generic usbserial code
  USB: visor: fix trivial accounting bug in visor driver
  USB: Fix throttling in generic usbserial driver
  USB: cp210x: Add support for the DW700 UART
  USB: ipaq: fix oops when device is plugged in
  USB: isp1362: fix build warnings on 64-bit systems
  USB: gadget: imx_udc: Use resource size
  USB: storage: iRiver P7 UNUSUAL_DEV patch
  USB: musb: make HAVE_CLK support optional
  USB: xhci: Fix dropping endpoints from the xHC schedule.
  USB: xhci: Don't wait for a disable slot cmd when HC dies.
  USB: xhci: Handle canceled URBs when HC dies.
  USB: xhci: Stop debugging polling loop when HC dies.
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: comedi: fix build on arches that don't want comedi drivers
  Staging: comedi: pcmcia irq fixes
  Staging: comedi: ni_pcimio: Added device id for pxi-6225.
  Staging: comedi: ni_65xx.c: fix output inversion problem.
  Staging: comedi: ni_65xx.c: fix insn_bits shift calculation.
  Staging: comedi: s526: fixes for pulse generator
  Staging: comedi: s526: Take account of arch's byte order.
  Staging: comedi: s526: Get rid of global variable 'cmReg'.
  Staging: comedi: s526: Fix number of channels on DIO subdevice
  Staging: comedi: cb_pcidio: fix "section mismatch" error
  Staging: comedi: jr3_pci: Initialize transf variable fully in jr3_pci_poll_subdevice().
  Staging: comedi: Corrected type of a printk argument in resize_async_buffer().
  Staging: p9auth: a few fixes
  Staging: rtl8192e: Add #include <linux/vmalloc.h>
  Staging: iio: Don't build on s390
  Staging: winbond: implement prepare_multicast and fix API usage
  Staging: w35und: Fix ->beacon_int breakage
  Staging: remove cowloop driver
  Staging: remove agnx driver
  Staging: comedi: serial2002: fix include build issue

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (s3c-hwmon) Disable build for S3C64xx
  MAINTAINERS: Fix Riku Voipio's address
  hwmon: (asus_atk0110) Enable the EC
  hwmon: (asus_atk0110) Refactor the code
  hwmon: (sht15) Fix spurious section mismatch warning

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: fix file clone ioctl for bookend extents
  Btrfs: fix uninit compiler warning in cow_file_range_nocow
  Btrfs: constify dentry_operations
  Btrfs: optimize back reference update during btrfs_drop_snapshot
  Btrfs: remove negative dentry when deleting subvolumne
  Btrfs: optimize fsync for the single writer case
  Btrfs: async delalloc flushing under space pressure
  Btrfs: release delalloc reservations on extent item insertion
  Btrfs: delay clearing EXTENT_DELALLOC for compressed extents
  Btrfs: cleanup extent_clear_unlock_delalloc flags
  Btrfs: fix possible softlockup in the allocator
  Btrfs: fix deadlock on async thread startup

After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (34 commits)
  [SCSI] qla2xxx: Fix NULL ptr deref bug in fail path during queue create
  [SCSI] st: fix possible memory use after free after MTSETBLK ioctl
  [SCSI] be2iscsi: Moving to pci_pools v3
  [SCSI] libiscsi: iscsi_session_setup to allow for private space
  [SCSI] be2iscsi: add 10Gbps iSCSI - BladeEngine 2 driver
  [SCSI] zfcp: Fix hang when offlining device with offline chpid
  [SCSI] zfcp: Fix lockdep warning when offlining device with offline chpid
  [SCSI] zfcp: Fix oops during shutdown of offline device
  [SCSI] zfcp: Fix initial device and cfdc for delayed adapter allocation
  [SCSI] zfcp: correctly initialize unchained requests
  [SCSI] mpt2sas: Bump version 02.100.03.00
  [SCSI] mpt2sas: Support dev remove when phy status is MPI2_EVENT_SAS_TOPO_PHYSTATUS_VACANT
  [SCSI] mpt2sas: Timeout occurred within the HANDSHAKE logic while waiting on firmware to ACK.
  [SCSI] mpt2sas: Call init_completion on a per request basis.
  [SCSI] mpt2sas: Target Reset will be issued from Interrupt context.
  [SCSI] mpt2sas: Added SCSIIO, Internal and high priority memory pools to support multiple TM
  [SCSI] mpt2sas: Copyright change to 2009.
  [SCSI] mpt2sas: Added mpi2_history.txt for MPI2 headers.
  [SCSI] mpt2sas: Update driver to MPI2 REV K headers.
  [SCSI] bfa: Brocade BFA FC SCSI driver
  ...

GFP_ATOMIC without good cause is evil.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb:usbserial:visor: fix race between unthrottle and completion handler

visor_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.

the same bug as opticon.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

many serial subdrivers are clearly written as if throttle/unthrottle
cannot sleep. This leads to unneeded atomic submissions. This
patch converts affected drivers in a way to makes very clear that
throttle/unthrottle can sleep. Thus future misdesigns can be avoided
and efficiency and reliability improved.

This removes any such assumption using GFP_KERNEL and spin_lock_irq()
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb:usbserial:symbolserial: fix race between unthrottle and completion handler

symbol_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.

the same bug as opticon.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb:usbserial:opticon: fix race between unthrottle and completion handler

opticon_unthrottle() mustn't resubmit the URB unconditionally
as the URB may still be running.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The EHCI driver does some bounds checking when it's scheduling an iTD for
an active endpoint.  It sets the local variable start to
stream->next_uframe and moves that variable further in the schedule if
necessary.  However, the driver fails to do anything with start before
jumping to the ready label and setting the URB's starting frame to
stream->next_uframe.  Alan Stern confirms the EHCI driver should set
stream->next_uframe to start before jumping.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1294) fixes a problem that has plagued users for several
kernel releases.  Some USB mass-storage devices don't return any sense
data when they encounter certain kinds of errors.  The SCSI layer
interprets this to mean that the operation should be retried, and the
same thing happens -- over and over again with no limit.  In some
circumstances (such as when a bus reset occurs) that is the right
thing to do, but not here.

The patch checks for this condition (a transport failure with no sense
data) and changes the result code to DID_ERROR and the sense code to
Hardware Error.  This does get only a limited number of retries, and
so the command will fail relatively quickly instead of getting stuck
in an infinite loop.

This fixes a large part of Bugzilla #14118.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Mantas Mikulenas <grawity@gmail.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb:usbserial: fix flags in error case of suspension

suspended flag must be reset in error case
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

usb:usbserial:visor: fix accounting in error case

data not pushed to the tty layer due to an error mustn't be counted
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The generic usbserial driver in Linux 2.6.31 halts its receiving
channel in response to throttle requests from the line discipline.
Unfortunately it drops the contents of the first URB received after
throttling takes effect. This patch corrects that problem.
Signed-off-by: Joris van Rantwijk <jorispubl@xs4all.nl>
Acked-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In the Dell inspiron mini 10, the GPS is connected via a cp2102. This patch
adds detection of this USB device. (I haven't managed to use the GPS under
Linux yet, though)
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1293) fixes a problem with the ipaq serial driver.  It
tries to bind to all the interfaces, even those that don't have enough
endpoints.  The symptom is an invalid memory reference and oops when
the device is plugged in.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable <stable@kernel.org>
Tested-by: Matthias Geissert <geissert@mathematik.tu-darmstadt.de>
Tested-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

A bunch of places assumed pointers were 32-bits in size (bit checking and
debug output), but none of these affected runtime functionality.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one errors.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The Blackfin port doesn't support HAVE_CLK and the musb driver works fine
with support stubbed out, so take the existing Blackfin clk stubs and move
them to common musb code so we can drop the Kconfig dependency.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When an endpoint is to be dropped from the hardware bandwidth schedule, we
want to clear its add flag.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When the host controller dies or is removed while a device is plugged in,
the USB core will attempt to deallocate the struct usb_device.  That will
call into xhci_free_dev().  This function used to attempt to submit a
disable slot command to the host controller and clean up the device
structures when that command returned.  Change xhci_free_dev() to skip the
command submission and just free the memory if the host controller died.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When the host controller dies (e.g. it is removed from a PCI card slot),
the xHCI driver cannot expect commands to complete.  The buggy code this
patch fixes would mark an URB as canceled and then expect the URB to be
completed when the stop endpoint command completed.  That would never
happen if the host controller was dead, so the USB core would just hang in
the disconnect code.

If the host controller died, and the driver asks to cancel an URB, free
any structures associated with that URB and immediately give it back.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

If the host controller card is removed from the system, stop the timer
function to debug the xHCI rings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The current 10ms timeout is too short for some normal USBTMC device
operation, increase it to a value which was tested with previously
affected Tektronix oscilloscopes.
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Peter Magdina <peter@magdina.sk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Stanse found a memory leak in lcd_probe. Instead of returning without
releasing the memory, jump to the error label which frees it.

http://stanse.fi.muni.cz/Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Updated sierra driver version from 1.3.7 to 1.3.8 now that the autosuspend
capabilities were added to the driver.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1295) fixes a recently-added bug in the USB serial core.
If certain kinds of errors occur during probing, the core may call a
serial driver's release method without previously calling the attach
method.  This causes some drivers (io_ti in particular) to perform an
invalid memory access.

The patch adds a new flag to keep track of whether or not attach has
been called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jean-Denis Girard <jd.girard@sysnux.pf>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch fixes a regression introduced in
39892da4.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix regression introduced by commit
d4fc4a7b (tty: Fix the PL2303 private
methods for sysrq).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>