This patch adds support to pick Tx queue based on the Rx queue(s) map
configuration set by the admin through the sysfs attribute
for each Tx queue. If the user configuration for receive queue(s) map
does not apply, then the Tx queue selection falls back to CPU(s) map
based selection and finally to hashing.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new field to sock_common 'skc_rx_queue_mapping'
which holds the receive queue number for the connection. The Rx queue
is marked in tcp_finish_connect() to allow a client app to do
SO_INCOMING_NAPI_ID after a connect() call to get the right queue
association for a socket. Rx queue is also marked in tcp_conn_request()
to allow syn-ack to go on the right tx-queue associated with
the queue on which syn is received.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change 'skc_tx_queue_mapping' field in sock_common structure from
'int' to 'unsigned short' type with ~0 indicating unset and
other positive queue values being set. This will accommodate adding
a new 'unsigned short' field in sock_common in the next patch for
rx_queue_mapping.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use static_key for XPS maps to reduce the cost of extra map checks,
similar to how it is used for RPS and RFS. This includes static_key
'xps_needed' for XPS and another for 'xps_rxqs_needed' for XPS using
Rx queues map.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor XPS code to support Tx queue selection based on
CPU(s) map or Rx queue(s) map.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Petr Machata says:

====================
mlxsw: Add resource scale tests

There are a number of tests that check features of the Linux networking
stack. By running them on suitable interfaces, one can exercise the
mlxsw offloading code. However none of these tests attempts to push
mlxsw to the limits supported by the ASIC.

As an additional wrinkle, the "limits supported by the ASIC" themselves
may not be a set of fixed numbers, but rather depend on a profile that
determines how the ASIC resources are allocated for different purposes.

This patchset introduces several tests that verify capability of mlxsw
to offload amounts of routes, flower rules, and mirroring sessions that
match predicted ASIC capacity, at different configuration profiles.
Additionally they verify that amounts exceeding the predicted capacity
can *not* be offloaded.

These are not generic tests, but ones that are tailored for mlxsw
specifically. For that reason they are not added to net/forwarding
selftests subdirectory, but rather to a newly-added drivers/net/mlxsw.

Patches #1, #2 and #3 tweak the generic forwarding/lib.sh to support the
new additions.

In patches #4 and #5, new libraries for interfacing with devlink are
introduced, first a generic one, then a Spectrum-specific one.

In patch #6, a devlink resource test is introduced.

Patches #7 and #8, #9 and #10, and #11 and #12 introduce three scale
tests: router, flower and mirror-to-gretap. The first of each pair of
patches introduces a generic portion of the test (mlxsw-specific), the
second introduces a Spectrum-specific wrapper.

Patch #13 then introduces a scale test driver that runs (possibly a
subset of) the tests introduced by patches from previous paragraph.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a scale test capable of validating that offloaded network
functionality is indeed functional at scale when configured to
the different KVD profiles available.

Start by testing offloaded routes are functional at scale by
passing traffic on each one of them in turn.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a wrapper around mlxsw/mirror_gre_scale.sh that parameterized number
of offloadable mirrors on Spectrum machines.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that it's possible to offload a given number of mirrors.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a wrapper around mlxsw/tc_flower_scale.sh that parameterizes the
generic tc flower scale test template with Spectrum-specific target
values.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add test of capacity to offload flower.

This is a generic portion of the test that is meant to be called from a
driver that supplies a particular number of rules to be tested with.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv4 routes in Spectrum are based on the kvd single-hash, but as it's
a hash we need to assume we cannot reach 100% of its capacity.

Add a wrapper that provides us with good/bad target numbers for the
Spectrum ASIC.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
[petrm@mellanox.com: Drop shebang.]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This test aims for both stand alone and internal usage by the resource
infra. The test receives the number routes to offload and checks:
- The routes were offloaded correctly
- Traffic for each route.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a selftest that can be used to perform basic sanity of the devlink
resource API as well as test the behavior of KVD manipulation in the
driver.

This is the first case of a HW-only test - in order to test the devlink
resource a driver capable of exposing resources has to be provided
first.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
[petrm@mellanox.com: Extracted two patches out of this patch. Tweaked
commit message.]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This library builds on top of devlink_lib.sh and contains functionality
specific to Spectrum ASICs, e.g., re-partitioning the various KVD
sub-parts.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
[petrm@mellanox.com: Split this out from another patch. Fix line length
in devlink_sp_read_kvd_defaults().]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This helper library contains wrappers to devlink functionality agnostic
to the underlying device.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
[petrm@mellanox.com: Split this out from another patch.]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

setup_wait() and tc_offload_check() both assume that all NUM_NETIFS
interfaces are relevant for a given test. However, the scale test script
acts as an umbrella for a number of sub-tests, some of which may not
require all the interfaces.

Thus it's suboptimal for tc_offload_check() to query all the interfaces.
In case of setup_wait() it's incorrect, because the sub-test in question
of course doesn't configure any interfaces beyond what it needs, and
setup_wait() then ends up waiting indefinitely for the extraneous
interfaces to come up.

For that reason, give setup_wait() and tc_offload_check() an optional
parameter with a number of interfaces to probe. Fall back to global
NUM_NETIFS if the parameter is not given.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the scale testing scenarios, one usually has a condition that is
expected to either fail, or pass, depending on which side of the scale
is being tested.

To capture this logic, add a function check_err_fail(), which dispatches
either to check_err() or check_fail(), depending on the value of the
first argument, should_fail.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The devlink related scripts are mlxsw-specific. As a result, they'll
reside in a different directory - but would still need the common logic
implemented in lib.sh.
So as a preliminary step, allow lib.sh to be sourced from other
directories as well.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: flower updates and netconsole

This set contains assorted updates to driver base and flower.
First patch is a follow up to a fix to calculating counters which
went into net.  For ethtool counters we should also make sure
they are visible even after ring reconfiguration.  Next patch
is a safety measure in case we are running on a machine with a
broken BIOS we should fail the probe when risk of incorrect
operation is too high.  The next two patches add netpoll support
and make use of napi_consume_skb().  Last we populate bus info
on all representors.

Pieter adds support for offload of the checksum action in flower.

John follows up to another fix he's done in net, we set TTL
values on tunnels to stack's default, now Johns does a full
route lookup to get a more precise information, he populates
ToS field as well.  Last but not least he follows up on Jiri's
request to enable LAG offload in case the team driver is used
and then hash function is unknown.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the NFP fw only supports L3/L4 hashing so rejects the offload of
filters that output to LAG ports implementing other hash algorithms. Team,
however, uses a BPF function for the hash that is not defined. To support
Team offload, accept hashes that are defined as 'unknown' (only Team
defines such hash types). In this case, use the NFP default of L3/L4
hashing for egress port selection.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extract the tos and the tunnel flags from the tunnel key and offload these
action fields. Only the checksum and tunnel key flags are implemented in
fw so reject offloads of other flags. The tunnel key flag is always
considered set in the fw so enforce that it is set in the rule. Note that
the compulsory setting of the tunnel key flag and optional setting of
checksum is inline with how tc currently generates ipv4 udp tunnel
actions.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously the ttl for ipv4 udp tunnels was set to the namespace default.
Modify this to attempt to extract the ttl from a full route lookup on the
tunnel destination. If this is not possible then resort to the default.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware will automatically update csum in headers when a set action has
been performed. This means we could in the driver ignore the explicit
checksum action when performing a set action.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We used to leave bus-info in ethtool driver info empty for
representors in case multi-PCIe-to-single-host cards make
the association between PCIe device and NFP many to one.
It seems these attempts are futile, we need to link the
representors to one PCIe device in sysfs to get consistent
naming, plus devlink uses one PCIe as a handle, anyway.
The multi-PCIe-to-single-system support won't be clean,
if it ever comes.

Turns out some user space (RHEL tests) likes to read bus-info
so just populate it.

While at it remove unnecessary app NULL-check, representors
are spawned by an app, so it must exist.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use napi_consume_skb() in nfp_net_tx_complete() to get bulk free.
Pass 0 as budget for ctrl queue completion since it runs out of
a tasklet.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NFP NAPI handling will only complete the TXed packets when called
with budget of 0, implement ndo_poll_controller by scheduling NAPI
on all TX queues.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On some platforms with broken ACPI tables we may not have access
to the Serial Number PCIe capability.  This capability is crucial
for us for switchdev operation as we use serial number as switch ID,
and for communication with management FW where interface ID is used.

If we can't determine the Serial Number we have to fail device probe.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After user changes the ring count statistics for deactivated
rings disappear from ethtool -S output.  This causes loss of
information to the user and means that ethtool stats may not
add up to interface stats.  Always expose counters from all
the rings.  Note that we allocate at most num_possible_cpus()
rings so number of rings should be reasonable.

The alternative of only listing stats for rings which were
ever in use could be confusing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling skb_unclone() is expensive as it triggers a memcpy operation.
Instead of calling skb_unclone() unconditionally, call it only when skb
has a shared frag_list. This improves tls rx throughout significantly.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Suggested-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Create unittests for the tc tunnel_key action.

v2:
For the tests expecting failures, added non-zero exit codes in the
teardowns. This prevents those tests from failing if the act_tunnel_key
module is unloaded.
Signed-off-by: Keara Leibovitz <kleib@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-davem-2018-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Small merge conflict in net/mac80211/scan.c, I preserved
the kcalloc() conversion. -DaveM

Johannes Berg says:

====================
This round's updates:
 * finally some of the promised HE code, but it turns
   out to be small - but everything kept changing, so
   one part I did in the driver was >30 patches for
   what was ultimately <200 lines of code ... similar
   here for this code.
 * improved scan privacy support - can now specify scan
   flags for randomizing the sequence number as well as
   reducing the probe request element content
 * rfkill cleanups
 * a timekeeping cleanup from Arnd
 * various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit extends the existing TIPC socket diagnostics framework
for information related to TIPC group communication.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A peer node is considered down if there are no
active links (or) lost contact to the node. In current implementation,
a peer node instance is deleted either if

a) TIPC module is removed (or)
b) Application can use a netlink/iproute2 interface to delete a
specific down node.

Thus, a down node instance lives in the system forever, unless the
application explicitly removes it.

We fix this by deleting the nodes which are down for
a specified amount of time (5 minutes).
Existing node supervision timer is used to achieve this.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The very first version of RTL8169 from 2002 (and only this one) has
support for a TBI 1000BaseX fiber interface. The TBI support in the
driver makes switching to phylib tricky, so best would be to get
rid of it. I found no report from anybody using a device with RTL8169
and fiber interface, also the vendor driver doesn't support this mode
(any longer).
So remove TBI support and bail out with a message if a card with
activated TBI is detected. If there really should be any user of it
out there, we could add a stripped-down version of the driver
supporting chip version 01 and TBI only (and maybe move it to
staging).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In single-link usage, the function tipc_node_timeout() still iterates
over the whole link array to handle each link. Given that the maximum
number of bearers are 3, there are 2 redundant iterations with lock
grab/release. Since this function is executing very frequently it makes
sense to optimize it.

This commit adds conditional checking to exit from the loop if the
known number of configured links has already been accessed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function tipc_msg_extract() is using skb_clone() to clone inner
messages from a message bundle buffer. Although this method is safe,
it has an undesired effect that each buffer clone inherits the
true-size of the bundling buffer. As a result, the buffer clone
almost always ends up with being copied anyway by the message
validation function. This makes the cloning into a sub-optimization.

In this commit we take the consequence of this realization, and copy
each inner message to a separately allocated buffer up front in the
extraction function.

As a bonus we can now eliminate the two cases where we had to copy
re-routed packets that may potentially go out on the wire again.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation of adding phylib support to the r8169 driver we need
PHY drivers for all chip-internal PHY types. Fortunately almost all
of them are either supported by the Realtek PHY driver already or work
with the genphy driver.
Still missing is support for the PHY of RTL8169s, it requires a quirk
to properly support 100Mbit-fixed mode. The quirk was copied from
r8169 driver which copied it from the vendor driver.
Based on the PHYID the internal PHY seems to be a RTL8211.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I see no need to define a private debug output symbol, let's use the
standard debug output functions instead. In this context also remove
the deprecated PFX define.

The one assertion is wrong IMO anyway, this code path is used also
by chip version 01.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>