- 14 Dec, 2011 4 commits
-
-
Barak Witkowski authored
Signed-off-by:
Barak Witkowski <barak@broadcom.com> Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
commit 6d4cdf47 (vlan: add 802.1q netpoll support) forgot to declare as static some private functions. Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> CC: Benjamin LaHaise <bcrl@kvack.org> Signed-off-by:
-
Dan Carpenter authored
The original code generates a Sparse warning: net/8021q/vlan_core.c:336:9: error: incompatible types in comparison expression (different address spaces) It's ok to dereference __rcu pointers here because we are holding the RTNL lock. I've added some calls to rtnl_dereference() to silence the warning. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Jiri Pirko <jpirko@redhat.com> Signed-off-by:
-
Eric Dumazet authored
Before adding a struct rtnl_link_ops into link_ops list, check it doesnt clash with a prior one. Based on a previous patch from Alexander Smirnov Signed-off-by:
-
- 13 Dec, 2011 36 commits
-
-
David S. Miller authored
Don't just succeed with a route that has a NULL neighbour attached. This follows the behavior of addrconf_dst_alloc(). Allowing this kind of route to end up with a NULL neigh attached will result in packet drops on output until the route is somehow invalidated, since nothing will meanwhile try to lookup the neigh again. A statistic is bumped for the case where we see a neigh-less route on output, but the resulting packet drop is otherwise silent in nature, and frankly it's a hard error for this to happen and ipv6 should do what ipv4 does which is say something in the kernel logs. Signed-off-by: -
David S. Miller authored
It's simpler to just keep these things out until there is a real user of them, so we can see what the needs actually are, rather than keep these things around as useless overhead. Signed-off-by: -
Yevgeny Petrilin authored
Signed-off-by:
Yevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by:
-
Yevgeny Petrilin authored
Signed-off-by:
-
Jack Morgenstein authored
1. Added module parameters sr_iov and probe_vf for controlling enablement of SRIOV mode. 2. Increased default max num-qps, num-mpts and log_num_macs to accomodate SRIOV mode 3. Added port_type_array as a module parameter to allow driver startup with ports configured as desired. In SRIOV mode, only ETH is supported, and this array is ignored; otherwise, for the case where the FW supports both port types (ETH and IB), the port_type_array parameter is used. By default, the port_type_array is set to configure both ports as IB. 4. When running in sriov mode, the master needs to initialize the ICM eq table to hold the eq's for itself and also for all the slaves. 5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap. 6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca). VFs obtain their startup information from the PF (master) device via the comm channel. 7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver aborts loading the device. 8. Do not allow setting port type via sysfs when running in SRIOV mode. 9. mlx4_get_ownership: Currently, only one PF is supported by the driver. If the HCA is burned with FW which enables more than one PF, only one of the PFs is allowed to run. The first one up grabs a FW ownership semaphone -- all other PFs will find that semaphore taken, and the driver will not allow them to run. Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Liran Liss <liranl@mellanox.co.il> Signed-off-by:
Marcel Apfelbaum <marcela@mellanox.co.il> Signed-off-by:
-
Jack Morgenstein authored
When running in SRIOV mode, driver should not automatically start/stop the mlx4_core upon sensing an HCA internal error -- doing this disables/enables sriov, which will cause the hypervisor to hang if there are running VMs with attached VFs. In addition, on VMs the catas process should not run at all, since the HCA error buffer is not available to VMs in the BARs. Signed-off-by:
-
Marcel Apfelbaum authored
In the previous implementation mtts are managed by: 1. order - log(mtt segments), 'mtt segment' groups several mtts together. 2. first_seg - segment location relative to mtt table. In the current implementation: 1. order - log(mtts) rather than segments 2. offset - mtt index in mtt table Note: The actual mtt allocation is made in segments but it is transparent to callers. Rational: The mtt resource holders are not interested on how the allocation of mtt is done, but rather on how they will use it. Signed-off-by:Marcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by:
-
Eugenia Emantayev authored
To enable internal loopback, always fill DMAC in control segment when transmitting the packet, once this is done, the packet is subject for loopback for if the DMAC mathces one of the multicast/unicast addresses registered on the physical port. In receive path if source MAC is our own MAC and we are not in selftest, or not in force LB mode - drop this packet. Signed-off-by:
Eugenia Emantayev <eugenia@mellanox.co.il> Signed-off-by:
-
Eugenia Emantayev authored
The physical port is now common to the PF and VFs. The port resources and configuration is managed by the PF, VFs can only influence the MTU of the port, it is set as max among all functions, Each function allocates RX buffers of required size to meet it's MTU enforcement. Port management code was moved to mlx4_core, as the mlx4_en module is virtualization unaware Move handling qp functionality to mlx4_get_eth_qp/mlx4_put_eth_qp including reserve/release range and add/release unicast steering. Let mlx4_register/unregister_mac deal only with MAC (un)registration. Signed-off-by:
-
Eugenia Emantayev authored
Let multicast/unicast attaching flow go through resource tracker. The PF is the one responsible for managing all the steering entries. Define and use module parameter that determines the number of qps per multicast group. Minor changes in function calls according to changed prototype. Signed-off-by:
-
Jack Morgenstein authored
Signed-off-by:
-
Eli Cohen authored
The resource tracker is used to track usage of HCA resources by the different guests. Virtual functions (VFs) are attached to guest operating systems but resources are allocated from the same pool and are assigned to VFs. It is essential that hostile/buggy guests not be able to affect the operation of other VFs, possibly attached to other guest OSs since ConnectX firmware is not tolerant to misuse of resources. The resource tracker module associates each resource with a VF and maintains state information for the allocated object. It also defines allowed state transitions and enforces them. Relationships between resources are also referred to. For example, CQs are pointed to by QPs, so it is forbidden to destroy a CQ if a QP refers to it. ICM memory is always accessible through the primary function and hence it is allocated by the owner of the primary function. When a guest dies, an FLR is generated for all the VFs it owns and all the resources it used are freed. The tracked resource types are: QPs, CQs, SRQs, MPTs, MTTs, MACs, RES_EQs, and XRCDNs. Signed-off-by:
Eli Cohen <eli@mellanox.co.il> Signed-off-by:
-
Jack Morgenstein authored
Passing async events to slaves: In SRIOV mode, each slave creates its own async EQ, but only the master can register directly with the FW to receive async events. Async events which should be passed to slaves (such as a WQ_ACCESS_ERROR for a QP owned by a slave) are generated at the slave by the master using the GEN_EQE FW command. Wrapper functions: mlx4_MAP_EQ_wrapper Only the master can map an EQ. The slave commands to map their EQs arrive at the master via the comm channel. The master then invokes the wrapper function to do the work (and enter the resource in the tracking database). New events: COMM_CHANNEL and FLR The COMM_CHANNEL event arrives only at the master, and signals that a slave has posted a command on the comm channel. The FLR event is generated by the FW when a guest operating a VF unexpectedly goes down. Signed-off-by:
-
Jack Morgenstein authored
MTTs are resources which are allocated and tracked by the PF driver. In multifunction mode, the allocation and icm mapping is done in the resource tracker (later patch in this sequence). To accomplish this, we have "work" functions whose names start with "__", and "request" functions (same name, no __). If we are operating in multifunction mode, the request function actually results in comm-channel commands being sent (ALLOC_RES or FREE_RES). The PF-driver comm-channel handler will ultimately invoke the "work" (__) function and return the result. If we are not in multifunction mode, the "work" handler is invoked immediately. Signed-off-by:
-
Jack Morgenstein authored
CQs are resources which are allocated and tracked by the PF driver. In multifunction mode, the allocation and icm mapping is done in the resource tracker (later patch in this sequence). To accomplish this, we have "work" functions whose names start with "__", and "request" functions (same name, no __). If we are operating in multifunction mode, the request function actually results in comm-channel commands being sent (ALLOC_RES or FREE_RES). The PF-driver comm-channel handler will ultimately invoke the "work" (__) function and return the result. If we are not in multifunction mode, the "work" handler is invoked immediately. Signed-off-by:
-
Jack Morgenstein authored
QPs are resources which are allocated and tracked by the PF driver. In multifunction mode, the allocation and icm mapping is done in the resource tracker (later patch in this sequence). To accomplish this, we have "work" functions whose names start with "__", and "request" functions (same name, no __). If we are operating in multifunction mode, the request function actually results in comm-channel commands being sent (ALLOC_RES or FREE_RES). The PF-driver comm-channel handler will ultimately invoke the "work" (__) function and return the result. If we are not in multifunction mode, the "work" handler is invoked immediately. Signed-off-by:
-
Jack Morgenstein authored
SRQs are resources which are allocated and tracked by the PF driver. In multifunction mode, the allocation and icm mapping is done in the resource tracker (later patch in this sequence). To accomplish this, we have "work" functions whose names start with "__", and "request" functions (same name, no __). If we are operating in multifunction mode, the request function actually results in comm-channel commands being sent (ALLOC_RES or FREE_RES). The PF-driver comm-channel handler will ultimately invoke the "work" (__) function and return the result. If we are not in multifunction mode, the "work" handler is invoked immediately. Signed-off-by:
-
Marcel Apfelbaum authored
The following commands are added here: 1. QUERY_FUNC_CAP and its wrapper. This function is used by VFs when they start up to receive configuration information from the PF, such as resource quotas for this VF, which ports should be used (currently two), what protocol is running on the port (currently Ethernet ONLY, or port not active). 2. QUERY_PORT and its wrapper. Previously, this FW command was invoked directly by the ETH driver (en_port.c) using mlx4_cmd_box. Virtualization is now required here (the VF's MAC address must be substituted for the PFs MAC address returned by the FW). We changed the invocation in the ETH driver to use mlx4_QUERY_PORT, and added the wrapper. 3. QUERY_HCA. Used by the VF to determine how the HCA was initialized. For now, we need only the multicast table member entry size (log2_mc_table_entry_sz, in the ConnectX PRM). No wrapper is needed here, because the data may be passed as is to the VF without modification). In this command, we have added a GLOBAL_CAPS field for passing required configuration information from FW to a VF (this field is to allow safely adding new SRIOV capabilities which require support in VF drivers, too). Bits will set here by FW in response to PF-driver configuration commands which will activate as yet undefined new SRIOV features. The VF will test to see that all required capabilities indicated by this field are supported (i.e., if a bit is set and the VF driver does not recognize that bit, it must abort its initialization). Currently, no bits are set. 4. Added a CLOSE_PORT wrapper. The PF context needs to keep track of how many VF contexts have the port open. The PF context will not actually issue the FW close port command until the last port user issues a CLOSE_PORT request. Signed-off-by: -
Yevgeny Petrilin authored
When SRIOV is enabled, pf and vfs communicate via shared comm channel. The vf gets its side of the comm channel via a VF BAR. Each VF (slave) creates its vHCR (virtual HCA Command Register), Its DMA address is passed to the PF (master) using Communication Channel Register. The same Register is used to notify the master of commands posted by the slaves and for the master to pass events to the slaves, such as command completions and asynchronous events. The vHCR format is identical to the HCR format, except for the 'go' and 't' bits, which are reserved in the vHCR. Posting commands to the vHCR is identical to the way it is done with the HCR, albeit that the function/PF token fields are used instead of the HCR go bit. Specifically: - When the function prepares a new command in the vHCR, it issues the Post_vHCR_cmd communication channel command and toggles the value of the function token; when PF token has an equal value, the command has been accepted and a new command may be posted. - When the PF detects a Post_vHCR_cmd command, it concludes that a new command is available in the vHCR; after processing the command, the PF toggles the PF token to match the function token. When the 'e' bit is not set, the completion of a Post_vHCR_cmd command also indicates the completion the vHCR command. If, however, the 'e' bit is set, the completion of a Post_vHCR_cmd command only indicates that the vHCR command has been accepted for execution by the PF. Function commands are processed by the PF as follows: -DMA (using the ACCESS_MEM command) the vHCR image into a shadow buffer. -Validate that the opcode is non-privileged, and that the opcode- and input-modifiers are legal. -DMA the in-box (if required) into a shadow buffer. -Validate the command: o Resource ranges (e.g., QP ranges). o Partition key. o Ranges of referenced resources (e.g., CQs within QP contexts). -If the 'e' bit is set o complete the Post_vHCR_cmd command -Execute the command on the HCR. -DMA the results to the vHCR out-box (if required). -If the 'e' bit is set o Indicate command completion by generating a completion event using the GEN_EQE command -Otherwise o DMA the command status to the vHCR o Complete the Post_vHCR_cmd command Signed-off-by:
Yevgeny Petrillin <yevgenyp@mellanox.com> Signed-off-by:
Liran Liss <liranl@mellanox.com> Signed-off-by:
-
Jack Morgenstein authored
When SRIOV is enabled on the chip (at FW burning time), the HCA uses only 17 bits for the PD. The remaining 7 high-order bits are ignored. Change the allocator to return only 17 bits for the PD. The MSB 7 bits will be used to encode the slave number for consistency checking later on in the resource tracker. Signed-off-by:
-
Jack Morgenstein authored
For SRIOV, some Hypervisor commands can be executed directly (native = 1). Others should go through the command wrapper flow (for tracking resource usage, for example, or for changing some HCA configurations that slaves need to be notified of). This patch sets the groundwork for this capability -- adding the correct value of "native" in each case. Note that if SRIOV is not activated, this parameter has no effect. Signed-off-by:
-
Jack Morgenstein authored
Port mask now has additional state. Port can be set as "none". In this case neither the mlx4_en or mlx4_ib drivers take ownership of the port. In multifunction mode there is an option to set the vfs as single ported devices. (in single function mode, both physical ports belong to same function) Signed-off-by:
-
Jack Morgenstein authored
These changes will not affect module operation as yet. They are only to get some structs and enums in place for use by subsequent patches (making those smaller). Added here: * sriov state structs and inlines (mlx4_is_master/slave/mfunc) * comm-channel and vhcr support structures * enum values for new FW and comm-channel virtual commands (i.e., commands, passed via the comm channel to the PF-driver). * prototypes for many command wrapper functions (used by the PF context for processing FW commands passed to it by the VFs). * struct mlx4_eqe is moved from eq.c to mlx4.h (it will be used by other mlx4_core source files). Signed-off-by:
-
Eric Dumazet authored
Reported-by:
Christoph Paasch <christoph.paasch@uclouvain.be> Signed-off-by:
-
Sathya Perla authored
- use adapter->num_vfs (and not the module param) to store the actual number of vfs created. Use the same variable to reflect SRIOV enable/disable state. So, drop the adapter->sriov_enabled field. - use for_all_vfs() macro in VF configuration code - drop the "vf_" prefix for the fields of be_vf_cfg; the prefix is redundant and removing it helps reduce line wrap Signed-off-by:
Sathya Perla <sathya.perla@emulex.com> Signed-off-by:
-
Sathya Perla authored
The ethtool "-g" option is supposed to report the max queue length and user modified queue length for RX and TX queues. be2net doesn't support user modification of queue lengths. So, the correct values for these would be the max numbers. be2net incorrectly reports the queue used values for these fields. Signed-off-by:
-
Dmitry Kravkov authored
Since commit e52fcb24 newly allocated skb for small packets are not updated properly and dropped by stack. Signed-off-by:
Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
-
Hagen Paul Pfeifer authored
This extension can be used to simulate special link layer characteristics. Simulate because packet data is not modified, only the calculation base is changed to delay a packet based on the original packet size and artificial cell information. packet_overhead can be used to simulate a link layer header compression scheme (e.g. set packet_overhead to -20) or with a positive packet_overhead value an additional MAC header can be simulated. It is also possible to "replace" the 14 byte Ethernet header with something else. cell_size and cell_overhead can be used to simulate link layer schemes, based on cells, like some TDMA schemes. Another application area are MAC schemes using a link layer fragmentation with a (small) header each. Cell size is the maximum amount of data bytes within one cell. Cell overhead is an additional variable to change the per-cell-overhead (e.g. 5 byte header per fragment). Example (5 kbit/s, 20 byte per packet overhead, cell-size 100 byte, per cell overhead 5 byte): tc qdisc add dev eth0 root netem rate 5kbit 20 100 5 Signed-off-by:
Hagen Paul Pfeifer <hagen@jauu.net> Signed-off-by:
Florian Westphal <fw@strlen.de> Acked-by:
Stephen Hemminger <shemminger@vyatta.com> Signed-off-by:
-
-
Glauber Costa authored
This patch introduces kmem.tcp.max_usage_in_bytes file, living in the kmem_cgroup filesystem. The root cgroup will display a value equal to RESOURCE_MAX. This is to avoid introducing any locking schemes in the network paths when cgroups are not being actively used. All others, will see the maximum memory ever used by this cgroup. Signed-off-by:
Glauber Costa <glommer@parallels.com> Reviewed-by:
Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by:
-
Glauber Costa authored
This patch introduces kmem.tcp.failcnt file, living in the kmem_cgroup filesystem. Following the pattern in the other memcg resources, this files keeps a counter of how many times allocation failed due to limits being hit in this cgroup. The root cgroup will always show a failcnt of 0. Signed-off-by:
-
Glauber Costa authored
This patch introduces kmem.tcp.usage_in_bytes file, living in the kmem_cgroup filesystem. It is a simple read-only file that displays the amount of kernel memory currently consumed by the cgroup. Signed-off-by:
-
Glauber Costa authored
This patch uses the "tcp.limit_in_bytes" field of the kmem_cgroup to effectively control the amount of kernel memory pinned by a cgroup. This value is ignored in the root cgroup, and in all others, caps the value specified by the admin in the net namespaces' view of tcp_sysctl_mem. If namespaces are being used, the admin is allowed to set a value bigger than cgroup's maximum, the same way it is allowed to set pretty much unlimited values in a real box. Signed-off-by:
-
Glauber Costa authored
This patch allows each namespace to independently set up its levels for tcp memory pressure thresholds. This patch alone does not buy much: we need to make this values per group of process somehow. This is achieved in the patches that follows in this patchset. Signed-off-by:
-
Glauber Costa authored
This patch introduces memory pressure controls for the tcp protocol. It uses the generic socket memory pressure code introduced in earlier patches, and fills in the necessary data in cg_proto struct. Signed-off-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtisu.com> CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by:
-
Glauber Costa authored
The goal of this work is to move the memory pressure tcp controls to a cgroup, instead of just relying on global conditions. To avoid excessive overhead in the network fast paths, the code that accounts allocated memory to a cgroup is hidden inside a static_branch(). This branch is patched out until the first non-root cgroup is created. So when nobody is using cgroups, even if it is mounted, no significant performance penalty should be seen. This patch handles the generic part of the code, and has nothing tcp-specific. Signed-off-by:
KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujtsu.com> CC: Kirill A. Shutemov <kirill@shutemov.name> CC: David S. Miller <davem@davemloft.net> CC: Eric W. Biederman <ebiederm@xmission.com> CC: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
