geneve->sock4/6 were added with geneve_open and released with geneve_stop.
So when geneve link down, we will not able to show remote address and
checksum info after commit 11387fe4 ("geneve: fix fill_info when using
collect_metadata").

Fix this by avoid passing *_REMOTE{,6} for COLLECT_METADATA since they are
mutually exclusive, and always show UDP_ZERO_CSUM6_RX info.

Fixes: 11387fe4 ("geneve: fix fill_info when using collect_metadata")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pcpu_freelist_pop() needs the same lockdep awareness than
pcpu_freelist_populate() to avoid a false positive.

 [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]

 switchto-defaul/12508 [HC0[0]:SC0[6]:HE0:SE0] is trying to acquire:
  (&htab->buckets[i].lock){......}, at: [<ffffffff9dc099cb>] __htab_percpu_map_update_elem+0x1cb/0x300

 and this task is already holding:
  (dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2){+.-...}, at: [<ffffffff9e135848>] __dev_queue_xmit+0
x868/0x1240
 which would create a new lock dependency:
  (dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2){+.-...} -> (&htab->buckets[i].lock){......}

 but this new dependency connects a SOFTIRQ-irq-safe lock:
  (dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2){+.-...}
 ... which became SOFTIRQ-irq-safe at:
   [<ffffffff9db5931b>] __lock_acquire+0x42b/0x1f10
   [<ffffffff9db5b32c>] lock_acquire+0xbc/0x1b0
   [<ffffffff9da05e38>] _raw_spin_lock+0x38/0x50
   [<ffffffff9e135848>] __dev_queue_xmit+0x868/0x1240
   [<ffffffff9e136240>] dev_queue_xmit+0x10/0x20
   [<ffffffff9e1965d9>] ip_finish_output2+0x439/0x590
   [<ffffffff9e197410>] ip_finish_output+0x150/0x2f0
   [<ffffffff9e19886d>] ip_output+0x7d/0x260
   [<ffffffff9e19789e>] ip_local_out+0x5e/0xe0
   [<ffffffff9e197b25>] ip_queue_xmit+0x205/0x620
   [<ffffffff9e1b8398>] tcp_transmit_skb+0x5a8/0xcb0
   [<ffffffff9e1ba152>] tcp_write_xmit+0x242/0x1070
   [<ffffffff9e1baffc>] __tcp_push_pending_frames+0x3c/0xf0
   [<ffffffff9e1b3472>] tcp_rcv_established+0x312/0x700
   [<ffffffff9e1c1acc>] tcp_v4_do_rcv+0x11c/0x200
   [<ffffffff9e1c3dc2>] tcp_v4_rcv+0xaa2/0xc30
   [<ffffffff9e191107>] ip_local_deliver_finish+0xa7/0x240
   [<ffffffff9e191a36>] ip_local_deliver+0x66/0x200
   [<ffffffff9e19137d>] ip_rcv_finish+0xdd/0x560
   [<ffffffff9e191e65>] ip_rcv+0x295/0x510
   [<ffffffff9e12ff88>] __netif_receive_skb_core+0x988/0x1020
   [<ffffffff9e130641>] __netif_receive_skb+0x21/0x70
   [<ffffffff9e1306ff>] process_backlog+0x6f/0x230
   [<ffffffff9e132129>] net_rx_action+0x229/0x420
   [<ffffffff9da07ee8>] __do_softirq+0xd8/0x43d
   [<ffffffff9e282bcc>] do_softirq_own_stack+0x1c/0x30
   [<ffffffff9dafc2f5>] do_softirq+0x55/0x60
   [<ffffffff9dafc3a8>] __local_bh_enable_ip+0xa8/0xb0
   [<ffffffff9db4c727>] cpu_startup_entry+0x1c7/0x500
   [<ffffffff9daab333>] start_secondary+0x113/0x140

 to a SOFTIRQ-irq-unsafe lock:
  (&head->lock){+.+...}
 ... which became SOFTIRQ-irq-unsafe at:
 ...  [<ffffffff9db5971f>] __lock_acquire+0x82f/0x1f10
   [<ffffffff9db5b32c>] lock_acquire+0xbc/0x1b0
   [<ffffffff9da05e38>] _raw_spin_lock+0x38/0x50
   [<ffffffff9dc0b7fa>] pcpu_freelist_pop+0x7a/0xb0
   [<ffffffff9dc08b2c>] htab_map_alloc+0x50c/0x5f0
   [<ffffffff9dc00dc5>] SyS_bpf+0x265/0x1200
   [<ffffffff9e28195f>] entry_SYSCALL_64_fastpath+0x12/0x17

 other info that might help us debug this:

 Chain exists of:
   dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2 --> &htab->buckets[i].lock --> &head->lock

  Possible interrupt unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(&head->lock);
                                local_irq_disable();
                                lock(dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2);
                                lock(&htab->buckets[i].lock);
   <Interrupt>
     lock(dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2);

  *** DEADLOCK ***

Fixes: e19494ed ("bpf: introduce percpu_freelist")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GetNtbFormat and SetNtbFormat requests operate on 16 bit little
endian values. We get away with ignoring this most of the time, because
we only care about USB_CDC_NCM_NTB16_FORMAT which is 0x0000.  This
fails for USB_CDC_NCM_NTB32_FORMAT.

Fix comparison between LE value from device and constant by converting
the constant to LE.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Fixes: 2b02c20c ("cdc_ncm: Set NTB format again after altsetting switch for Huawei devices")
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: Christian Panton <christian@panton.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It seems that the intention of the code is to null check the value
returned by function genlmsg_put. But the current code is null
checking the address of the pointer that holds the value returned
by genlmsg_put.

Fix this by properly null checking the value returned by function
genlmsg_put in order to avoid a pontential null pointer dereference.

Addresses-Coverity-ID: 1461561 ("Dereference before null check")
Addresses-Coverity-ID: 1461562 ("Dereference null return value")
Fixes: 96fbc13d ("openvswitch: Add meter infrastructure")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Hemminger says:

====================
netem: fix compilation on 32 bit

A couple of places where 64 bit CPU was being assumed incorrectly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix compilation on 32 bit platforms (where doing modulus operation
with 64 bit requires extra glibc functions) by truncation.
The jitter for table distribution is limited to a 32 bit value
because random numbers are scaled as 32 bit value.

Also fix some whitespace.

Fixes: 99803171 ("netem: add uapi to express delay and jitter in nanoseconds")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since times are now expressed in nanosecond, need to now do
true 64 bit divide. Old code would truncate rate at 32 bits.
Rename function to better express current usage.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make default TCP default congestion control to a per namespace
value. This changes default congestion control to a pointer to congestion ops
(rather than implicit as first element of available lsit).

The congestion control setting of new namespaces is inherited
from the current setting of the root namespace.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is at least unlocked deletion of net->ipv4.fib_notifier_ops
from net::fib_notifier_ops:

ip_fib_net_exit()
  rtnl_unlock()
  fib4_notifier_exit()
    fib_notifier_ops_unregister(net->ipv4.notifier_ops)
      list_del_rcu(&ops->list)

So fib_seq_sum() can't use rtnl_lock() only for protection.

The possible solution could be to use rtnl_lock()
in fib_notifier_ops_unregister(), but this adds
a possible delay during net namespace creation,
so we better use rcu_read_lock() till someone
really needs the mutex (if that happens).
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With commits 35e015e1 and a2d3f3e3, the global 'accept_dad' flag
is also taken into account (default value is 1). If either global or
per-interface flag is non-zero, DAD will be enabled on a given interface.

This is not backward compatible: before those patches, the user could
disable DAD just by setting the per-interface flag to 0. Now, the
user instead needs to set both flags to 0 to actually disable DAD.

Restore the previous behaviour by setting the default for the global
'accept_dad' flag to 0. This way, DAD is still enabled by default,
as per-interface flags are set to 1 on device creation, but setting
them to 0 is enough to disable DAD on a given interface.

- Before 35e015e1f57a7 and a2d3f3e3:
          global    per-interface    DAD enabled
[default]   1             1              yes
            X             0              no
            X             1              yes

- After 35e015e1 and a2d3f3e3:
          global    per-interface    DAD enabled
[default]   1             1              yes
            0             0              no
            0             1              yes
            1             0              yes

- After this fix:
          global    per-interface    DAD enabled
            1             1              yes
            0             0              no
[default]   0             1              yes
            1             0              yes

Fixes: 35e015e1 ("ipv6: fix net.ipv6.conf.all interface DAD handlers")
Fixes: a2d3f3e3 ("ipv6: fix net.ipv6.conf.all.accept_dad behaviour for real")
CC: Stefano Brivio <sbrivio@redhat.com>
CC: Matteo Croce <mcroce@redhat.com>
CC: Erik Kline <ek@google.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move inclusion of a private kernel header <net/tcp.h>
from uapi/linux/tls.h to its only user - net/tls.h,
to fix the following linux/tls.h userspace compilation error:

/usr/include/linux/tls.h:41:21: fatal error: net/tcp.h: No such file or directory

As to this point uapi/linux/tls.h was totaly unusuable for userspace,
cleanup this header file further by moving other redundant includes
to net/tls.h.

Fixes: 3c4d7559 ("tls: kernel TLS support")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

iOS devices require the host to be "trusted" before servicing network
packets. Establishing trust requires the user to confirm a dialog on the
iOS device.Until trust is established, the iOS device will silently discard
network packets from the host. Currently, the ipheth driver does not detect
whether an iOS device has established trust with the host, and immediately
sets up the transmit queues.

This causes the following problems:

- Kernel taint due to WARN() in netdev watchdog.
- Dmesg spam ("TX timeout").
- Disruption of user space networking activity (dhcpd, etc...) when new
interface comes up but cannot be used.
- Unnecessary host and device wakeups and USB traffic

Example dmesg output:

[ 1101.319778] NETDEV WATCHDOG: eth1 (ipheth): transmit queue 0 timed out
[ 1101.319817] ------------[ cut here ]------------
[ 1101.319828] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:316 dev_watchdog+0x20f/0x220
[ 1101.319831] Modules linked in: ipheth usbmon nvidia_drm(PO) nvidia_modeset(PO) nvidia(PO) iwlmvm mac80211 iwlwifi btusb btrtl btbcm btintel qmi_wwan bluetooth cfg80211 ecdh_generic thinkpad_acpi rfkill [last unloaded: ipheth]
[ 1101.319861] CPU: 0 PID: 0 Comm: swapper/0 Tainted: P           O    4.13.12.1 #1
[ 1101.319864] Hardware name: LENOVO 20ENCTO1WW/20ENCTO1WW, BIOS N1EET62W (1.35 ) 11/10/2016
[ 1101.319867] task: ffffffff81e11500 task.stack: ffffffff81e00000
[ 1101.319873] RIP: 0010:dev_watchdog+0x20f/0x220
[ 1101.319876] RSP: 0018:ffff8810a3c03e98 EFLAGS: 00010292
[ 1101.319880] RAX: 000000000000003a RBX: 0000000000000000 RCX: 0000000000000000
[ 1101.319883] RDX: ffff8810a3c15c48 RSI: ffffffff81ccbfc2 RDI: 00000000ffffffff
[ 1101.319886] RBP: ffff880c04ebc41c R08: 0000000000000000 R09: 0000000000000379
[ 1101.319889] R10: 00000100696589d0 R11: 0000000000000378 R12: ffff880c04ebc000
[ 1101.319892] R13: 0000000000000000 R14: 0000000000000001 R15: ffff880c2865fc80
[ 1101.319896] FS:  0000000000000000(0000) GS:ffff8810a3c00000(0000) knlGS:0000000000000000
[ 1101.319899] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1101.319902] CR2: 00007f3ff24ac000 CR3: 0000000001e0a000 CR4: 00000000003406f0
[ 1101.319905] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1101.319908] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1101.319910] Call Trace:
[ 1101.319914]  <IRQ>
[ 1101.319921]  ? dev_graft_qdisc+0x70/0x70
[ 1101.319928]  ? dev_graft_qdisc+0x70/0x70
[ 1101.319934]  ? call_timer_fn+0x2e/0x170
[ 1101.319939]  ? dev_graft_qdisc+0x70/0x70
[ 1101.319944]  ? run_timer_softirq+0x1ea/0x440
[ 1101.319951]  ? timerqueue_add+0x54/0x80
[ 1101.319956]  ? enqueue_hrtimer+0x38/0xa0
[ 1101.319963]  ? __do_softirq+0xed/0x2e7
[ 1101.319970]  ? irq_exit+0xb4/0xc0
[ 1101.319976]  ? smp_apic_timer_interrupt+0x39/0x50
[ 1101.319981]  ? apic_timer_interrupt+0x8c/0xa0
[ 1101.319983]  </IRQ>
[ 1101.319992]  ? cpuidle_enter_state+0xfa/0x2a0
[ 1101.319999]  ? do_idle+0x1a3/0x1f0
[ 1101.320004]  ? cpu_startup_entry+0x5f/0x70
[ 1101.320011]  ? start_kernel+0x444/0x44c
[ 1101.320017]  ? early_idt_handler_array+0x120/0x120
[ 1101.320023]  ? x86_64_start_kernel+0x145/0x154
[ 1101.320028]  ? secondary_startup_64+0x9f/0x9f
[ 1101.320033] Code: 20 04 00 00 eb 9f 4c 89 e7 c6 05 59 44 71 00 01 e8 a7 df fd ff 89 d9 4c 89 e6 48 c7 c7 70 b7 cd 81 48 89 c2 31 c0 e8 97 64 90 ff <0f> ff eb bf 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00
[ 1101.320103] ---[ end trace 0cc4d251e2b57080 ]---
[ 1101.320110] ipheth 1-5:4.2: ipheth_tx_timeout: TX timeout

The last message "TX timeout" is repeated every 5 seconds until trust is
established or the device is disconnected, filling up dmesg.

The proposed patch eliminates the problem by, upon connection, keeping the
TX queue and carrier disabled until a packet is first received from the iOS
device. This is reflected by the confirmed_pairing variable in the device
structure. Only after at least one packet has been received from the iOS
device, the transmit queue and carrier are brought up during the periodic
device poll in ipheth_carrier_set. Because the iOS device will always send
a packet immediately upon trust being established, this should not delay
the interface becoming useable. To prevent failed UBRs in
ipheth_rcvbulk_callback from perpetually re-enabling the queue if it was
disabled, a new check is added so only successful transfers re-enable the
queue, whereas failed transfers only trigger an immediate poll.

This has the added benefit of removing the periodic control requests to the
iOS device until trust has been established and thus should reduce wakeup
events on both the host and the iOS device.
Signed-off-by: Alexander Kappner <agk@godking.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

We always poll tx for socket, this is sub optimal since this will
slightly increase the waitqueue traversing time and more important,
vhost could not benefit from commit 9e641bdc ("net-tun:
restructure tun_do_read for better sleep/wakeup efficiency") even if
we've stopped rx polling during handle_rx(), tx poll were still left
in the waitqueue.

Pktgen from a remote host to VM over mlx4 on two 2.00GHz Xeon E5-2650
shows 11.7% improvements on rx PPS. (from 1.28Mpps to 1.44Mpps)

Cc: Wei Xu <wexu@redhat.com>
Cc: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Consistently use types provided by <linux/types.h> to fix the following
linux/rxrpc.h userspace compilation errors:

/usr/include/linux/rxrpc.h:24:2: error: unknown type name 'u16'
  u16  srx_service; /* service desired */
/usr/include/linux/rxrpc.h:25:2: error: unknown type name 'u16'
  u16  transport_type; /* type of transport socket (SOCK_DGRAM) */
/usr/include/linux/rxrpc.h:26:2: error: unknown type name 'u16'
  u16  transport_len; /* length of transport address */

Use __kernel_sa_family_t instead of sa_family_t the same way
as uapi/linux/in.h does, to fix the following
linux/rxrpc.h userspace compilation errors:

/usr/include/linux/rxrpc.h:23:2: error: unknown type name 'sa_family_t'
  sa_family_t srx_family; /* address family */
/usr/include/linux/rxrpc.h:28:3: error: unknown type name 'sa_family_t'
  sa_family_t family;  /* transport address family */

Fixes: 727f8914 ("rxrpc: Expose UAPI definitions to userspace")
Cc: <stable@vger.kernel.org> # v4.14
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The LPI transitioning logic in stmmac_main uses
priv->tx_path_in_lpi_mode to enter/exit LPI.

However, priv->tx_path_in_lpi_mode is assigned
using the return value from host_irq_status().

So for dwmac4, priv->tx_path_in_lpi_mode was always false,
so stmmac_tx_clean() would always try to put us in eee mode,
and stmmac_xmit() would never take us out of eee mode.

To fix this, make host_irq_status() read and return the LPI
irq status also for dwmac4.

This also increments the existing LPI counters, so that
ethtool --statistics shows LPI transitions also for dwmac4.

For dwmac1000, irqs are enabled/disabled using the register
named "Interrupt Mask Register", and thus setting a bit disables
that specific irq.

For dwmac4 the matching register is named "MAC_Interrupt_Enable",
and thus setting a bit enables that specific irq.

Looking at dwmac1000_core.c, the irqs that are always enabled are:
LPI and PMT.

Looking at dwmac4_core.c, the irqs that are always enabled are:
PMT.

To be able to read the LPI irq status, we need to enable the LPI
irq also for dwmac4.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm_dev_register() can fail here and passed parameters to free irq
which is not initialised. Initialization of 'dev->irq' happened after
the 'goto out_free_irq'. So using 'irq' insted of 'dev->irq' in
free_irq().
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds netlink notifications on iflias changes via sysfs.
makes it consistent with the netlink path which also calls
netdev_state_change. Also makes it consistent with other sysfs
netdev_store operations.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warnings:

net/openvswitch/flow_netlink.c:340:8: warning:
 symbol 'ovs_nsh_key_attr_size' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of error, the function ovs_meter_cmd_reply_start() returns
ERR_PTR() not NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: 96fbc13d ("openvswitch: Add meter infrastructure")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We accidentally return success if lio_vf_rep_modinit() fails instead of
propogating the error code.

Fixes: e20f4696 ("liquidio: synchronize VF representor names with NIC firmware")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The assert statement is supposed to be part of the else branch but the
curly braces were accidentally left off.

Fixes: 3e29cd0e ("xdp: Sample xdp program implementing ip forward")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements and enables VDP support for the ibmvnic driver.
Moreover, it includes the implementation of suitable structs, signal
 transmission/handling and functions which allows the retrival of firmware
 information from the ibmvnic card through the ethtool command.
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Found another missing port flag policy entry for IFLA_BRPORT_VLAN_TUNNEL
so add it now.

CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Fixes: efa5356b ("bridge: per vlan dst_metadata netlink support")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mvneta controller provides a 8-bit register to update the pending
Tx descriptor counter. Then, a maximum of 255 Tx descriptors can be
added at once. In the current code the mvneta_txq_pend_desc_add function
assumes the caller takes care of this limit. But it is not the case. In
some situations (xmit_more flag), more than 255 descriptors are added.
When this happens, the Tx descriptor counter register is updated with a
wrong value, which breaks the whole Tx queue management.

This patch fixes the issue by allowing the mvneta_txq_pend_desc_add
function to process more than 255 Tx descriptors.

Fixes: 2a90f7e1 ("net: mvneta: add xmit_more support")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These flags are unused, remove them to be less confusing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink_skb_destructor() is actually defined before the first usage
in the file, so remove the unnecessary forward declaration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The lan9303 set bits in the host CPU tag indicating if a ingress frame
is a trapped IGMP or STP frame. Use these bits to calculate
skb->offload_fwd_mark more efficiently.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch migrates the HNS3 driver code from use of depricated PCI
MSI/MSI-X interrupt vector allocation/free APIs to new common APIs.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function devm_gpiod_get_optional() returns an ERR_PTR on failure. Its
return value should not be validated by a NULL check. Instead, use IS_ERR.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit b94d22d9 "ARM64: dts: meson-gx: add external PHY
interrupt on some platforms" ethernet stopped working on my Odroid-C2
which has a RTL8211F phy.

It turned out that no interrupts were triggered. Further analysis
showed the register INER can't be altered on page 0.
Because register INSR needs to be accessed via page 0xa43 I assumed
that register INER needs to be accessed via some page too.
Some brute force check resulted in page 0xa42 being the right one.

With this patch the phy is working properly in interrupt mode.

Fixes: 3447cf2e ("net/phy: Add support for Realtek RTL8211F")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Update firmware version

Ido says:

This set adjusts the driver to use a new firmware version. The new
version includes various enhancements and fixes detailed in the first
patch.

The second patch enables batch deletion of neighbours on a router
interface (RIF) which was not possible with previous versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 4a3c67a6 ("mlxsw: spectrum_router: Don't batch neighbour
deletion") I removed the support for batch deletion of neighbours on a
router interface (RIF) since at that time the firmware did not support
it for IPv6 neighbours.

This is now supported by the version enforced by the driver, so there is
no reason to delete neighbours one by one anymore.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This new firmware contains:
 - Support Spectrum A1 revision
 - Batch deletion of IPv6 neighbours
 - Remove incorrect VPD capability
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to
  https://www.mail-archive.com/netdev@vger.kernel.org/msg177411.html
there is a status page available at
  http://vger.kernel.org/~davem/net-next.html
to obtain the current status of the net-next tree.  Let's add this
information to the netdev FAQ.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

* clarify specification references for v0/v1
* add section "APN vs. Network device"
* add section "Local GTP-U entity and tunnel identification"
Signed-off-by: Andreas Schultz <aschultz@tpip.net>
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rasmus Villemoes says:

====================
net: core: devname allocation cleanups

It's somewhat confusing to have both dev_alloc_name and
dev_get_valid_name. I can't see why the former is less strict than the
latter, so make them (or rather dev_alloc_name_ns and
dev_get_valid_name) equivalent, hardening dev_alloc_name() a little.

Obvious follow-up patches would be to only export one function, and
make dev_alloc_name a static inline wrapper for that (whichever name
is chosen for the exported interface). But maybe there is a good
reason the two exported interfaces do different checking, so I'll
refrain from including the trivial but tree-wide renaming in this
series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If name contains a %, it's easy to see that this patch doesn't change
anything (other than eliminate the duplicate dev_valid_name
call). Otherwise, we'll now just spend a little time in snprintf()
copying name to the stack buffer allocated in dev_alloc_name_ns, and do
the __dev_get_by_name using that buffer rather than name.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we're given format string with no %d, -EEXIST is a saner error code.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently only exclude non-sysfs-friendly names via
dev_get_valid_name; there doesn't seem to be a reason to allow such
names when we're called via dev_alloc_name.

This does duplicate the dev_valid_name check in the dev_get_valid_name()
case; we'll fix that shortly.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>