Makes code a little shorter.
Signed-off-by: Andi Kleen <ak@suse.de>

Remove some unlinuxy ways to write function parameter definitions.
Remove some stray "return;"s

No functional change.

Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>

No functional changes.

Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>

They are not used in this file so remove them. i386 didn't have them either.

Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>

It used to contain support code for NUMAQ, but that is long gone already
on 64bit.
Signed-off-by: Andi Kleen <ak@suse.de>

Since we only support PCI and ISA legacy busses now there is no need to
have an full array with checking.
Signed-off-by: Andi Kleen <ak@suse.de>

They did not really belong into io_apic.c. Move them into a new file
and clean it up a bit.

Also remove outdated ATI quirk that was obsolete,
Signed-off-by: Andi Kleen <ak@suse.de>

The MPS table specification says that the operating system should
renumber the IO-APICs following the table as needed.  However in
ACPI this is not allowed or neeeded and all x86-64 systems are ACPI
compliant.

The code was already disabled on some systems because it caused
problems there. Remove it completely now.

CC: mdomsch@dell.com
Signed-off-by: Andi Kleen <ak@suse.de>

Bugzilla #6552 says:

"In arch/i386/boot/setup.S, movw is used instead of movb for PS/2 mouse
information, although it is unsigned char. This does not harm, because
the jmp instruction overwritten by movw is used before executing movw,
and never be used again"

I've no idea if this is a real bug or how it gets fixed, so I'm submitting
it for review instead of letting it die of boredom in bugzilla. Aditionally
to i386, I've changed x86-64, which mirrors the same code.

Credits to Yoshinori K. Okuji, who found the problem and suggested a fix.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Signed-off-by: Andi Kleen <ak@suse.de>

The IO APIC code had lots of duplicated code to read/write 64bit
routing entries into the IO-APIC. Factor this out int common read/write
functions

In a few cases the IO APIC lock is taken more often now, but this
isn't a problem because it's all initialization/shutdown only
slow path code.

Similar to earlier x86-64 patch.

Includes a fix by Jiri Slaby for a mistake that broke resume
Signed-off-by: Andi Kleen <ak@suse.de>

The IO APIC code had lots of duplicated code to read/write 64bit
routing entries into the IO-APIC. Factor this out int common read/write
functions

In a few cases the IO APIC lock is taken more often now, but this
isn't a problem because it's all initialization/shutdown only
slow path code.
Signed-off-by: Andi Kleen <ak@suse.de>

It apparently has never triggered in many years.
Signed-off-by: Andi Kleen <ak@suse.de>

PIC mode is an outdated way to drive the APICs that was used on
some early MP boards. It is not supported in the ACPI model.

It is unlikely to be ever configured by any x86-64 system

Remove it thus.
Signed-off-by: Andi Kleen <ak@suse.de>

No 64bit EISA or Microchannel systems ever. Remove the left over code
in the IO-APIC driver and the mptable parser
Signed-off-by: Andi Kleen <ak@suse.de>

This was an old workaround for broken MP-BIOS. The user could
specify overwrites on the command line.

I've never seen it being used for anything on 64bit. So get
rid of it for now.
Signed-off-by: Andi Kleen <ak@suse.de>

And remove some old obsolete ones.
Signed-off-by: Andi Kleen <ak@suse.de>

(based on x86-64 changes)
- Add a proper memory clobber to invlpg
- Remove an unused extern
Signed-off-by: Andi Kleen <ak@suse.de>

- Convert CR* accesses to dedicated inline functions and rewrite
the rest as C inlines
- Don't do a double flush for global flushes (pointed out by Zach Amsden)
This was a bug workaround for old CPUs that don't do 64bit and is obsolete.
- Add a proper memory clobber to invlpg
- Remove an unused extern
Signed-off-by: Andi Kleen <ak@suse.de>

The new systems already use focus disabled and the comment was
completely outdated.
Signed-off-by: Andi Kleen <ak@suse.de>

Nobody has been setting the mismatch counter and the ifdef was never
set so remove it.
Signed-off-by: Andi Kleen <ak@suse.de>

IO-APIC or local APIC can only be disabled at runtime anyways and
Kconfig has forced these options on for a long time now.

The Kconfigs are kept only now for the benefit of the shared acpi
boot.c code.
Signed-off-by: Andi Kleen <ak@suse.de>

Signed-off-by: Andi Kleen <ak@suse.de>

And move the comment to a proper place.
Signed-off-by: Andi Kleen <ak@suse.de>

- Move them to a pure assembly file. Previously they were in
a C file that only consisted of inline assembly. Doing it in pure
assembler is much nicer.
- Add a frame.i include with FRAME/ENDFRAME macros to easily
add frame pointers to assembly functions
- Add dwarf2 annotation to them so that the new dwarf2 unwinder
doesn't get stuck on them
- Random cleanups

Includes feedback from Jan Beulich and a UML build fix from Andrew
Morton.

Cc: jbeulich@novell.com
Cc: jdike@addtoit.com
Signed-off-by: Andi Kleen <ak@suse.de>

LOCK_PREFIX is replaced by nops on UP systems, so it has to be a special
macro.  Previously this was only possible from C. Allow it for pure
assembly files too. Similar to earlier x86-64 patch.
Signed-off-by: Andi Kleen <ak@suse.de>

Previously it didn't align. Use the same one as the C compiler
in blended mode, which is good for K8 and Core2 and doesn't hurt
on P4.
Signed-off-by: Andi Kleen <ak@suse.de>

rwlocks are now out of line, so it near never triggers.  Also it was
incompatible with the new dwarf2 unwinder because it had unannotiatable
push/pops.
Signed-off-by: Andi Kleen <ak@suse.de>

- Move the slow path fallbacks to their own assembly files
This makes them much easier to read and is needed for the next change.
- Add CFI annotations for unwinding (XXX need review)
- Remove constant case which can never happen with out of line spinlocks
- Use patchable LOCK prefixes
- Don't use lock sections anymore for inline code because they can't
be expressed by the unwinder (this adds one taken jump to the lock
fast path)

Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>

Signed-off-by: Andi Kleen <ak@suse.de>

Signed-off-by: Andi Kleen <ak@suse.de>

Use knowledge about EFLAGS layout (bits 22:63 are always 0) to distingush
EFLAGS word and kernel address in the spin lock stack frame.
Signed-off-by: Andi Kleen <ak@suse.de>

This ports the algorithm from x86-64 (with improvements) to i386.
Previously this only worked for frame pointer enabled kernels.
But spinlocks have a very simple stack frame that can be manually
analyzed. Do this.
Signed-off-by: Andi Kleen <ak@suse.de>

Based on patch from Frank van Maarseveen <frankvm@frankvm.com>, but
extended.
Signed-off-by: Andi Kleen <ak@suse.de>

A few trivial spelling and grammar mistakes picked up in
"arch/x86_64/aperture.c", "arch/x86_64/crash.c" and
"arch/x86_64/apic.c". I think all are correct fixes but am ever aware
of my fallibility :o) This is my first patch submission so all
feedback is appreciated, esp. WRT CCing to Linus, Andi and
trivial@kernel.org, is this correct? And which is the most appropriate
kernel version to diff against? If any.

Should apply cleanly to 2.6.18-rc1
Signed-off-by: Adam Henley <adamazing@gmail.com>
Signed-off-by: Andi Kleen <ak@suse.de>

-  adam

virtual addresses don't belong into kernel logs for non debugging

Cc: clemens@ladisch.de
Signed-off-by: Andi Kleen <ak@suse.de>

Hello,

Following my discussion with Andi. Here is a patch that introduces
two new TIF flags to simplify the context switch code in __switch_to().
The idea is to minimize the number of cache lines accessed in the common
case, i.e., when neither the debug registers nor the I/O bitmap are used.

This patch covers the x86-64 modifications. A patch for i386 follows.

Changelog:
	- add TIF_DEBUG to track when debug registers are active
	- add TIF_IO_BITMAP to track when I/O bitmap is used
	- modify __switch_to() to use the new TIF flags

<signed-off-by>: eranian@hpl.hp.com
Signed-off-by: Andi Kleen <ak@suse.de>

No need to include it from entry.S
Drop all the #ifdef __ASSEMBLY__
Signed-off-by: Andi Kleen <ak@suse.de>

For NUMA optimization and some other algorithms it is useful to have a fast
to get the current CPU and node numbers in user space.

x86-64 added a fast way to do this in a vsyscall. This adds a generic
syscall for other architectures to make it a generic portable facility.

I expect some of them will also implement it as a faster vsyscall.

The cache is an optimization for the x86-64 vsyscall optimization. Since
what the syscall returns is an approximation anyways and user space
often wants very fast results it can be cached for some time.  The norma
methods to get this information in user space are relatively slow

The vsyscall is in a better position to manage the cache because it has direct
access to a fast time stamp (jiffies). For the generic syscall optimization
it doesn't help much, but enforce a valid argument to keep programs
portable

I only added an i386 syscall entry for now. Other architectures can follow
as needed.

AK: Also added some cleanups from Andrew Morton
Signed-off-by: Andi Kleen <ak@suse.de>

This patch adds a vgetcpu vsyscall, which depending on the CPU RDTSCP
capability uses either the RDTSCP or CPUID to obtain a CPU and node
numbers and pass them to the program.

AK: Lots of changes over Vojtech's original code:
Better prototype for vgetcpu()
It's better to pass the cpu / node numbers as separate arguments
to avoid mistakes when going from SMP to NUMA.
Also add a fast time stamp based cache using a user supplied
argument to speed things more up.
Use fast method from Chuck Ebbert to retrieve node/cpu from
GDT limit instead of CPUID
Made sure RDTSCP init is always executed after node is known.
Drop printk
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>

This patch adds initalization of the RDTSCP auxilliary values to CPU numbers
to time.c. If RDTSCP is available, the MSRs are written with the respective
values. It can be later used to initalize per-cpu timekeeping variables.

AK: Some cleanups. Move externs into headers and fix CPU hotplug.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>