1. 13 Jul, 2018 9 commits
  2. 09 Jul, 2018 1 commit
  3. 04 Jul, 2018 10 commits
  4. 02 Jul, 2018 2 commits
    • Thomas Gleixner's avatar
      cpu/hotplug: Boot HT siblings at least once · 0cc3cd21
      Thomas Gleixner authored
      Due to the way Machine Check Exceptions work on X86 hyperthreads it's
      required to boot up _all_ logical cores at least once in order to set the
      CR4.MCE bit.
      
      So instead of ignoring the sibling threads right away, let them boot up
      once so they can configure themselves. After they came out of the initial
      boot stage check whether its a "secondary" sibling and cancel the operation
      which puts the CPU back into offline state.
      Reported-by: default avatarDave Hansen <dave.hansen@intel.com>
      Signed-off-by: default avatarThomas Gleixner <tglx@linutronix.de>
      Tested-by: default avatarTony Luck <tony.luck@intel.com>
      0cc3cd21
    • Thomas Gleixner's avatar
      Revert "x86/apic: Ignore secondary threads if nosmt=force" · 506a66f3
      Thomas Gleixner authored
      Dave Hansen reported, that it's outright dangerous to keep SMT siblings
      disabled completely so they are stuck in the BIOS and wait for SIPI.
      
      The reason is that Machine Check Exceptions are broadcasted to siblings and
      the soft disabled sibling has CR4.MCE = 0. If a MCE is delivered to a
      logical core with CR4.MCE = 0, it asserts IERR#, which shuts down or
      reboots the machine. The MCE chapter in the SDM contains the following
      blurb:
      
          Because the logical processors within a physical package are tightly
          coupled with respect to shared hardware resources, both logical
          processors are notified of machine check errors that occur within a
          given physical processor. If machine-check exceptions are enabled when
          a fatal error is reported, all the logical processors within a physical
          package are dispatched to the machine-check exception handler. If
          machine-check exceptions are disabled, the logical processors enter the
          shutdown state and assert the IERR# signal. When enabling machine-check
          exceptions, the MCE flag in control register CR4 should be set for each
          logical processor.
      
      Reverting the commit which ignores siblings at enumeration time solves only
      half of the problem. The core cpuhotplug logic needs to be adjusted as
      well.
      
      This thoughtful engineered mechanism also turns the boot process on all
      Intel HT enabled systems into a MCE lottery. MCE is enabled on the boot CPU
      before the secondary CPUs are brought up. Depending on the number of
      physical cores the window in which this situation can happen is smaller or
      larger. On a HSW-EX it's about 750ms:
      
      MCE is enabled on the boot CPU:
      
      [    0.244017] mce: CPU supports 22 MCE banks
      
      The corresponding sibling #72 boots:
      
      [    1.008005] .... node  #0, CPUs:    #72
      
      That means if an MCE hits on physical core 0 (logical CPUs 0 and 72)
      between these two points the machine is going to shutdown. At least it's a
      known safe state.
      
      It's obvious that the early boot can be hit by an MCE as well and then runs
      into the same situation because MCEs are not yet enabled on the boot CPU.
      But after enabling them on the boot CPU, it does not make any sense to
      prevent the kernel from recovering.
      
      Adjust the nosmt kernel parameter documentation as well.
      
      Reverts: 2207def7 ("x86/apic: Ignore secondary threads if nosmt=force")
      Reported-by: default avatarDave Hansen <dave.hansen@intel.com>
      Signed-off-by: default avatarThomas Gleixner <tglx@linutronix.de>
      Tested-by: default avatarTony Luck <tony.luck@intel.com>
      506a66f3
  5. 29 Jun, 2018 1 commit
  6. 27 Jun, 2018 1 commit
    • Vlastimil Babka's avatar
      x86/speculation/l1tf: Protect PAE swap entries against L1TF · 0d0f6249
      Vlastimil Babka authored
      The PAE 3-level paging code currently doesn't mitigate L1TF by flipping the
      offset bits, and uses the high PTE word, thus bits 32-36 for type, 37-63 for
      offset. The lower word is zeroed, thus systems with less than 4GB memory are
      safe. With 4GB to 128GB the swap type selects the memory locations vulnerable
      to L1TF; with even more memory, also the swap offfset influences the address.
      This might be a problem with 32bit PAE guests running on large 64bit hosts.
      
      By continuing to keep the whole swap entry in either high or low 32bit word of
      PTE we would limit the swap size too much. Thus this patch uses the whole PAE
      PTE with the same layout as the 64bit version does. The macros just become a
      bit tricky since they assume the arch-dependent swp_entry_t to be 32bit.
      Signed-off-by: default avatarVlastimil Babka <vbabka@suse.cz>
      Signed-off-by: default avatarThomas Gleixner <tglx@linutronix.de>
      Acked-by: default avatarMichal Hocko <mhocko@suse.com>
      0d0f6249
  7. 22 Jun, 2018 1 commit
  8. 21 Jun, 2018 15 commits