The indication that a descriptor ring flush is required was read from
FEXTNVM7 by mistake. It should be read from the PCI config space.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The condition under which the flush should occur was reversed.  The fix
should be applied before any HW reset (unless followed by bus reset)
and before any power state transition from D0.

If E1000_FEXTNVM7_NEED_DESCRING_FLUSH bit is set in FEXTNVM7 and TDLEN > 0
the Tx ring should be flushed. (fixes ~95% of the hang states).
If the E1000_FEXTNVM7_NEED_DESCRING_FLUSH did not clear, we should also
flush the RX ring. Bug was caught by Alexander Duyck during a code review
when examining this fix.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes a warning that was reported by Yanjiang Jin
<yanjiang.jin@windriver.com> by implementing the solution suggested by
Alexander Duyck <alexander.h.duyck@redhat.com>.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

After testing various cases, the conclusion is that the fix MUST be
executed BEFORE any event that the HW is reset or transition to D3.
To fix that I moved the execution to the relevant places but per
Alexander Duyck's review, ensure now that the DMA is valid and was not
freed before manipulating the ring.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Unit hang may occur if multiple descriptors are available in the rings
during reset or runtime suspend. This state can be detected by testing
bit 8 in the FEXTNVM7 register. If this bit is set and there are pending
descriptors in one of the rings, we must flush them prior to reset. Same
applies entering runtime suspend.
Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Shradha Shah says:

====================
sfc: ndo_get_phys_port_id, vadaptor stats and PF unload when Vf's assigned to guest

This is the third and last instalment of SRIOV for EF10 patches.

This patch set includes implementation of ndo_get_phys_port_id
and changes to the MAC statistics code in order to support
vadaptor statistics.

It also includes code to deal with PF unload when Vf's are still
assigned to the guest.

The first couple of patches create sysfs files for physical port
and link control flags which are particularly useful when we have
enabled a large number of VF's.

These patches have been tested with and without CONFIG_SFC_SRIOV.
The creation and content of the sysfs files has been tested.
The statistics are tested using ethtool for monitoring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If any VF is assigned as the PF is unloaded, do not attempt to
remove its vport or the vswitch.  These will be removed if the
driver binds to the PF again, as an entity reset occurs during
probe.

A 'force' flag is added to efx_ef10_pci_sriov_disable() to
distinguish between disabling SR-IOV and driver unload.
SR-IOV cannot be disabled if VFs are assigned to guests.

If the PF driver is unloaded while VFs are assigned, the driver
may try to bind to the VF again at a later point if the driver
has been reloaded and the VF returns to the same domain as the PF.
In this case, the PF will not have a VF data structure, so the VF
can check this and drop out of probe early.

In this case, efx->vf_count will be zero but VFs will be present.
The user is advised to remove the VF and re-create it. The check
at the beginning of efx_ef10_pci_sriov_disable() that
efx->vf_count is non-zero is removed to allow SR-IOV to be
disabled in this case. Also, if the PF driver is unloaded, it
will disable SR-IOV to remove these unknown VFs.

By not disabling bus-mastering if VFs are still assigned, the VF
will continue to pass traffic after the PF has been removed.

When using the max_vfs module parameter, if VFs are already
present do not try to initialise any more.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the driver unloads, force the unbind and removal of any
VFs in the host with the PF.  The PF cannot remove vports and
vswitches if they are still being used by a VF driver, and when
unloading the sfc driver the removal order is not guaranteed,
so the instruction from the PF to the VF to unbind enforces a
suitable ordering so that vswitches and vports can be removed.

As a result of this, manually unbinding the driver from a single
PF will result in all of its VFs in the host also being removed.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ifenslave command to set up a bond runs in an atomic
context, and it queries the stats on the devices that are
being enslaved. A VF needs to make an MCDI call to update
its stats, which is not allowed in atomic context.

The releasing of the stats_lock is moved to the beginning of
the VF stats update function so that in_interrupt() can be
used; it must be taken again before returning from this
function.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The raw_mask array is not initialised, so it needs to be
explicitly set to zero in the 'else' branch.

If the EVB capability is not present, a port cannot have multiple
functions so the per-port MAC stats are correct and should match
the corresponding vadaptor stats, so this redundancy can be
removed from the ethtool stats output.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MC_CMD_MAC_STATS can be called on a function before a
vadaptor has been created, as the kernel can call into this
through ndo_get_stats/ndo_get_stats64.

If MC_CMD_MAC_STATS is called before the DMA queues have been
setup, so that a vadaptor has not been created yet, firmware
will return ENOENT. This is expected, so suppress the MCDI
error message in this case.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netdevice statistics (in /proc/net/dev) are per-function
stats so they must use the vadaptor stats. Change the use of
MAC stats to vadaptor stats, and remove any statistics that
can only be measured per-port.  All stats that are removed
will be shown as zeroes when these statistics are displayed.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware does not support a periodic DMA of vadaptor-stats
on VFs, so only update the stats buffer when stats are
requested (when running "ethtool -S" or an ip/ifconfig
command that reports stats).
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All interfaces will display vadaptor statistics, so set all the
relevant bits in the stats bitmask. Only functions with the
LINKCTRL flag will see other stats, including (per-port) MAC stats.

The vadaptor stats are from rx_unicast to tx_overflow.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The port-id must be known so that the RMON level can be
set for the collection of vadapter stats.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC stats are per-port and will only be displayed on the PF
with control of the link (one per physical port). Vadapter stats
will also be displayed for this PF, so distinguish the MAC stats
by adding a prefix of "port_".
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On  every adapter there will be one primary PF per adaptor and
one link control PF per port.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change is a stylistic change and does not affect
functionality.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the case where we have multiple functions (PFs and VFs), this
sysfs entry is useful to identify the physical port corresponding
to the function we are interested in.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Aleksey Makarov says:

====================
net: thunderx: fix problems reported by static check tools

These are fixes for the problems that were reported by static check tools.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

GFP_KERNEL should be used in the thread context
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a coccinelle warning:

coccinelle warnings: (new ones prefixed by >>)

>> drivers/net/ethernet/cavium/thunder/nicvf_queues.c:360:1-11: alloc
>> with no test, possible model on line 367

vim +360 drivers/net/ethernet/cavium/thunder/nicvf_queues.c

   354		err = nicvf_alloc_q_desc_mem(nic, &sq->dmem, q_len,
SND_QUEUE_DESC_SIZE,
   355					     NICVF_SQ_BASE_ALIGN_BYTES);
   356		if (err)
   357			return err;
   358
   359		sq->desc = sq->dmem.base;
 > 360		sq->skbuff = kcalloc(q_len, sizeof(u64), GFP_ATOMIC);
   361		sq->head = 0;
   362		sq->tail = 0;
   363		atomic_set(&sq->free_cnt, q_len - 1);
   364		sq->thresh = SND_QUEUE_THRESH;
   365
   366		/* Preallocate memory for TSO segment's header */
 > 367		sq->tso_hdrs = dma_alloc_coherent(&nic->pdev->dev,
   368						  q_len *
TSO_HEADER_SIZE,
   369						  &sq->tso_hdrs_phys,
GFP_KERNEL);
   370		if (!sq->tso_hdrs)
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to cast void* to u8*: pointer arithmetics
works same way for both.
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes a copypaste bug that was discovered by a static analysis
tool:

The patch 4863dea3: "net: Adding support for Cavium ThunderX
network controller" from May 26, 2015, leads to the following static
checker warning:

        drivers/net/ethernet/cavium/thunder/nicvf_ethtool.c:517
nicvf_set_rxfh()
        warn: we tested 'hkey' before and it was 'false'

drivers/net/ethernet/cavium/thunder/nicvf_ethtool.c
   506          /* We do not allow change in unsupported parameters */
   507          if (hkey ||
                    ^^^^
We return here.

   508              (hfunc != ETH_RSS_HASH_NO_CHANGE && hfunc !=
ETH_RSS_HASH_TOP))
   509                  return -EOPNOTSUPP;
   510
   511          rss->enable = true;
   512          if (indir) {
   513                  for (idx = 0; idx < rss->rss_size; idx++)
   514                          rss->ind_tbl[idx] = indir[idx];
   515          }
   516
   517          if (hkey) {
                    ^^^^
So this is dead code.

   518                  memcpy(rss->key, hkey, RSS_HASH_KEY_SIZE *
sizeof(u64));
   519                  nicvf_set_rss_key(nic);
   520          }
   521
   522          nicvf_config_rss(nic);
   523          return 0;
   524  }

regards,
dan carpenter
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes sparse messages like this:

drivers/net/ethernet/cavium/thunder/nicvf_main.c:1141:26: sparse: symbol
'nicvf_get_stats64' was not declared. Should it be static?

Also remove unused declarations
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

They were left from development stage
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes sparse message:

drivers/net/ethernet/cavium/thunder/nicvf_main.c:385:40: sparse: cast to
restricted __le64
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes sparse message:

drivers/net/ethernet/cavium/thunder/nicvf_main.c:153:25: sparse: cast to
restricted __le64
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes sparse messages like this:

drivers/net/ethernet/cavium/thunder/thunder_bgx.c:897:24: sparse:
constant 0x300000000000 is so big it is long
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are duplicate NODE_ID macro definitions. Move all of them to
nic.h for usage in nic and bgx driver and introduce nic_get_node_id()
helper function.

This patch also fixes 64bit mask which should have been ULL by
reworking the node calculation.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/phy/amd-xgbe-phy.c
	drivers/net/wireless/iwlwifi/Kconfig
	include/net/mac80211.h

iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.

The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
cxgb4/cxgb4vf: Adds support for Chelsio T6 adapter

This patch series adds the following:
Adds NIC driver support for T6 adapter
Adds vNIC driver support for T6 adapter

This patch series has been created against net-next tree and includes
patches on cxgb4 and cxgb4vf driver.

We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.

Thanks

V2:
 Fixed compilation issue, when CHELSIO_T4_FCOE is set
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds vnic driver register related changes for T6 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds NIC driver related changes for T6 adapter. Register related
changes, MC related changes, VF related changes, doorbell related
changes, debugfs changes, etc
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds new macro is_t6 and adds the register address range for T6 adapter
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Various VTI tunnel (mark handling, PMTU) bug fixes from Alexander
    Duyck and Steffen Klassert.

 2) Revert ethtool PHY query change, it wasn't correct.  The PHY address
    selected by the driver running the PHY to MAC connection decides
    what PHY address GET ethtool operations return information from.

 3) Fix handling of sequence number bits for encryption IV generation in
    ESP driver, from Herbert Xu.

 4) UDP can return -EAGAIN when we hit a bad checksum on receive, even
    when there are other packets in the receive queue which is wrong.
    Just respect the error returned from the generic socket recv
    datagram helper.  From Eric Dumazet.

 5) Fix BNA driver firmware loading on big-endian systems, from Ivan
    Vecera.

 6) Fix regression in that we were inheriting the congestion control of
    the listening socket for new connections, the intended behavior
    always was to use the default in this case.  From Neal Cardwell.

 7) Fix NULL deref in brcmfmac driver, from Arend van Spriel.

 8) OTP parsing fix in iwlwifi from Liad Kaufman.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
  vti6: Add pmtu handling to vti6_xmit.
  Revert "net: core: 'ethtool' issue with querying phy settings"
  bnx2x: Move statistics implementation into semaphores
  xen: netback: read hotplug script once at start of day.
  xen: netback: fix printf format string warning
  Revert "netfilter: ensure number of counters is >0 in do_replace()"
  net: dsa: Properly propagate errors from dsa_switch_setup_one
  tcp: fix child sockets to use system default congestion control if not set
  udp: fix behavior of wrong checksums
  sfc: free multiple Rx buffers when required
  bna: fix soft lock-up during firmware initialization failure
  bna: remove unreasonable iocpf timer start
  bna: fix firmware loading on big-endian machines
  bridge: fix br_multicast_query_expired() bug
  via-rhine: Resigning as maintainer
  brcmfmac: avoid null pointer access when brcmf_msgbuf_get_pktid() fails
  mac80211: Fix mac80211.h docbook comments
  iwlwifi: nvm: fix otp parsing in 8000 hw family
  iwlwifi: pcie: fix tracking of cmd_in_flight
  ip_vti/ip6_vti: Preserve skb->mark after rcv_cb call
  ...

Pull Sparc fixes from David Miller:

 1) Setup the core/threads/sockets bitmaps correctly so that 'lscpus'
    and friends operate properly.  Frtom Chris Hyser.

 2) The bit that normally means "Cached Virtually" on sun4v systems,
    actually changes meaning in M7 and later chips.  Fix from Khalid
    Aziz.

 3) One some PCI-E systems we need to probe different OF properties to
    fill in the PCI slot information properly, from Eric Snowberg.

 4) Kill an extraneous memset after kzalloc(), from Christophe Jaillet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Resolve conflict between sparc v9 and M7 on usage of bit 9 of TTE
  sparc64: pci slots information is not populated in sysfs
  sparc: kernel: GRPCI2: Remove a useless memset
  sparc64: Setup sysfs to mark LDOM sockets, cores and threads correctly

Pull virtio fix from Michael Tsirkin:
 "Last-minute virtio fix for 4.1

  This tweaks an exported user-space header to fix build breakage for
  userspace using it"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  include/uapi/linux/virtio_balloon.h: include linux/virtio_types.h