Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Note: To utilize this configuration DPL and DPC must be changed
accordingly to enable dpmac 13+14 for sgmii.
Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

make modules_install will not generate the module dependencies file if
the depmod command is missing from the running system.
Add it as a requirement to runme.sh and include in Dockerfile.
Signed-off-by: Josua Mayer <josua@solid-run.com>

The -E flag for sudo has previously been removed to work around some
strange issues.
Re-add the safer --preserve-envs flag listing all the settings currently
available.

This allows in particular to override the serdes configuration again
without editing the runme.sh file - e.g.:
docker run -i -t -v "$PWD":/work -e SERDES=8S_9_2 lx2160a_build -u 0 -g 0
Signed-off-by: Josua Mayer <josua@solid-run.com>

The hack for configuring MAC XIF_MODE register pending mc firmware
support differentiates between some 10gbps and some 1gbps modes.
Add rgmii modes to avoid fall-through when using the wired phy.
Signed-off-by: Josua Mayer <josua@solid-run.com>

i2c muxes are reset with cpu reset and will default back to channel 0,
while any other channel may still be blocked by a slave.
Detect known muxes and flush all their channels if detected.

Further disable detection logic because it missed rare cases.
Reset unconditionally instead.
Signed-off-by: Josua Mayer <josua@solid-run.com>

The i2c bus may be blocked by anz slave device if the system was reset
during a transaction, leading to ddr initialisation failures.
Implement a workaround releasing the bus by toggling scl 9 times.
Signed-off-by: Josua Mayer <josua@solid-run.com>

Disable high-speed modes in Linux to ensure the microSD operates in the
same mode as it does during rcw and u-boot.

This is a work-around for when the system gets stuck after reset failing
to read from the microSD card.
Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Directly connect the sfp drivers's (sfp.c) link up and down events to an
LED node in device-tree. This solution is a workaround to the
shortcomings of the generic led triggers framework in combination with
multiple dynamic network interfaces, hot-pluggable phys (inside sfp
modules) and the dpaa2 driver in particular.
Signed-off-by: Josua Mayer <josua@solid-run.com>

The issue is that dpmac.16 to dpmac.18 links up, but unable to
communicate thru those ports.
This patch series does -
1. Fix dpmac.17 phy-handle type since by default the dpmac is RGMII, and
in half-twins case it is thru SGMII.
2. Add to the build script the usage of MC firmware 10.28.100; which is
based on 10.28.1 that fixes the tx/rx thru dpmac.16, dpmac.17 and
dpmac.18. This firmware is only for LSDK-21.08 and will be fixed in
later LSDK releases with newer MC firmwares.
3. Limit recycle queues in the half twins DPC to 1G; this makes it
possible for dpmac.18 to be able to transmit
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

1. Half twins is 8xSFP+ and 8xSFP with OCPv3 NIC support board
2. Using SD1=8S (PLLF=100MHz, PLLS=161.132825MHz) runtime downgrade from
10G to 1G, according to SFP module inserted is not supported
3. Reverted default DDR speed to 3200
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

Also fix buildroot compile error when running as root, and allow using a
local mirror.
Signed-off-by: Josua Mayer <josua@solid-run.com>

lx2160acex7: add support for SERDES1 mode 21, wich support 6x 25GB [Lanes 1-4 & Lane 7-8].
Signed-off-by: Yazan Shhady <yazan.shhady@solid-run.com>

- can work with podman
- added required packages
- allow using an apt proxy
Signed-off-by: Josua Mayer <josua@solid-run.com>

- Enabled CONFIG_SFP in the kernel build
- Pulled SFP device tree patch from mainline - this enables
dpmac7,8,9,10 that are the 4 SFP+ connectors on HoneyComb / ClearFog-CX
- Pulled AR8035 phy device tree patch
- Remove RTC interrupt from device tree
- Added power button support to device tree
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

This patch debootstraps debian bullseye under arm64 emulated buildroot
To build debian; run -

DISTRO=debian ./runme.sh
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

runme: check DDR speed before doing build

This patch adds most of the fixes to enable secure boot on the LX2160A
COM express -

1. The atf patches fixes the efuse fip fuse loading, and setting of ppwm
register and then gpio handling
2. The u-boot patches adds the secureboot defconfig, and then SVR_WO_E
mask fix
3. Patches for runme.sh script; for building the secure image run with
'SECURE=true ./runme.sh'

The missing piece is u-boot esbc validate code that completes the chain
of trust boot (COT).
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

1. Added support for LSDK-20.12
2. Added initial support for secure boot; there are few atf patches that
will be added later
3. Fixed documentation in README.md withregards SPI flashing to use
cmp.b instead of cmp (the size is given in bytes)
4. Added ATF debug/release build environment variable
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Add support for mode 4, which allows connectivity with 1000base-X and
SGMII to be used with the SFP and QSFP slots in conjunction with the
kernel's PCS support.
Signed-off-by: Russell King <rmk@armlinux.org.uk>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

ClearFog CX boards rev 1.3 and newer contains on carrier board retimers
to support 100Gbps DAC cables.
When configuring the SERDEses to 10Gbps the retimer configuration needs
to be changed to lock on 10.3125Gbps rate on both the ingress (i2c
address 0x23) and egress (i2c address 0x22) retimers.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

For machines that doesn't have sys_eeprom initialized, this can be done
in u-boot by -
sys_eeprom set 0x24 00:11:22:44:11:44
sys_eeprom set 0x2a 0x10
sys_eeprom write

The first command will set the base MAC, the second will define a range
of 16 MAC addresses (LX2 COM can actually go up to 17 MACs).
The third command will save the TLV data. After that reset is required
for the MAC addresses to get effective
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>