Signed-off-by: Josua Mayer <josua@solid-run.com>

lx2160acex7: add support for SERDES1 mode 21, wich support 6x 25GB [Lanes 1-4 & Lane 7-8].
Signed-off-by: Yazan Shhady <yazan.shhady@solid-run.com>

- can work with podman
- added required packages
- allow using an apt proxy
Signed-off-by: Josua Mayer <josua@solid-run.com>

- Enabled CONFIG_SFP in the kernel build
- Pulled SFP device tree patch from mainline - this enables
dpmac7,8,9,10 that are the 4 SFP+ connectors on HoneyComb / ClearFog-CX
- Pulled AR8035 phy device tree patch
- Remove RTC interrupt from device tree
- Added power button support to device tree
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

This patch debootstraps debian bullseye under arm64 emulated buildroot
To build debian; run -

DISTRO=debian ./runme.sh
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

runme: check DDR speed before doing build

This patch adds most of the fixes to enable secure boot on the LX2160A
COM express -

1. The atf patches fixes the efuse fip fuse loading, and setting of ppwm
register and then gpio handling
2. The u-boot patches adds the secureboot defconfig, and then SVR_WO_E
mask fix
3. Patches for runme.sh script; for building the secure image run with
'SECURE=true ./runme.sh'

The missing piece is u-boot esbc validate code that completes the chain
of trust boot (COT).
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

1. Added support for LSDK-20.12
2. Added initial support for secure boot; there are few atf patches that
will be added later
3. Fixed documentation in README.md withregards SPI flashing to use
cmp.b instead of cmp (the size is given in bytes)
4. Added ATF debug/release build environment variable
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Add support for mode 4, which allows connectivity with 1000base-X and
SGMII to be used with the SFP and QSFP slots in conjunction with the
kernel's PCS support.
Signed-off-by: Russell King <rmk@armlinux.org.uk>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

ClearFog CX boards rev 1.3 and newer contains on carrier board retimers
to support 100Gbps DAC cables.
When configuring the SERDEses to 10Gbps the retimer configuration needs
to be changed to lock on 10.3125Gbps rate on both the ingress (i2c
address 0x23) and egress (i2c address 0x22) retimers.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

For machines that doesn't have sys_eeprom initialized, this can be done
in u-boot by -
sys_eeprom set 0x24 00:11:22:44:11:44
sys_eeprom set 0x2a 0x10
sys_eeprom write

The first command will set the base MAC, the second will define a range
of 16 MAC addresses (LX2 COM can actually go up to 17 MACs).
The third command will save the TLV data. After that reset is required
for the MAC addresses to get effective
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

1. Rename DWC3 SS patch from .patc to .patch
2. Add power button support to LX2 COM PWRBTN# GPIO input
3. Set pinmuxing to correctly read SD card CD# signal when booting from
SPI / eMMC.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

issue found when working with 12c variant and CAN-FD is disabled (bit12)
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

1. Added TI based retimer initialization on 25Gbp SERDES configuration.
Note that those retimers are available on ClearFog CX revision 1.3 and
newer
2. Restructure SERDES configuration files
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

1. Fixed u-boot build when using u-boot release LSDK-20.04-update-290520
2. Added SD1 protocol #14 (100Gbps with PCIe gen3 x4) configuration
3. Removed UEFI from this git repository; mainline edk2-platforms now
supports most of the bits for LX2 and HoneyComb. For building uefi
repository refer to SolidRun github lx2160a_uefi repo.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

1. Poweroff the HoneyComb board by asserting SUS_S5# signal
2. Add USB3.0 DWC3 workaround by disabling parkmode
3. Keep flexspi divisor as default which is ~17MHz. This enables using
the carrier board SPI that is limited in speed due to the analogue mux
connected to it.
4. Remove uefi build and update LSDK20.04 to may-29 update. UEFI is
temporarily hosted at https://github.com/SolidRun/lx2160a_uefi until
fully upstreamed.
5. Add 4x25Gbps MC config
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>

u-boot: some tweaks to distro-boot for enabling standard debian

Signed-off-by: Josua Mayer <josua@solid-run.com>

Signed-off-by: Josua Mayer <josua@solid-run.com>

1. Manually edited patch 0018-lx... to fix atheros phy related config.
2. Just before booting the kernel toggle back the fan full speed signal
to enable the kernel driver to initialize the AMC6821 device
3. Add u-boot poweroff command that set S5# (GPIO3 7) signal to low;
thus turning off the HoneyComb / ClearFog CX boards.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>